| Age | Commit message (Collapse) | Author |
|---|
|
Enable sdcard UHS modes, up to SDR50, on p20x based boards.
While the s905 supports SDR104 mode, it appears that the PCB of p20x
based boards can't cope with a rate as high as 200Mhz.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Enable sdcard UHS modes up to SDR50. Unfortunately, it seems the PCB of
the libretech-cc cannot handle SDR104 at 200Mhz reliably.
Also enable eMMC DDR52 mode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Changing the card voltage on the cc is not instantaneous, especially
when switching from 3.3v to 1.8v.
It take at least 30ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: 61ff2af9b278 ("ARM64: dts: fixup libretech cc definition")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Changing the card voltage on the nanopi-k2 is not instantaneous,
especially when switching from 3.3v to 1.8v.
It take at least 3ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: 9bc7ffb08daf ("arm64: dts: amlogic: Add NanoPi K2")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Now that the clock source 0 is properly described in the CCF, use it
instead of assuming the default value (xtal)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch describes the GPIO lines usage on the LibreTech CC board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: minor whiespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Linux 4.13-rc4
|
|
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The AO clkc needs to be updated to new bindings with an system control parent
node and moving the clkc node as subnode.
Also adds the SoC specific compatible following the bindings requirements.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
git://github.com/BayLibre/clk-meson into v4.14/dt64
Amlogic clock headers updates for 4.14
* meson8b: add the reset controller to the clkc
* meson: expose all clk ids
* gxbb-aoclk: Add CEC 32k clock
* gxbb: add mmc input 0 clocks
* meson: fix protection against undefined clks
* tag 'meson-clk-headers-for-4.14' of git://github.com/BayLibre/clk-meson:
dt-bindings: clock: gxbb-aoclk: Add CEC 32k clock
clk: meson: gxbb: Add sd_emmc clk0 clkids
clk: meson-gxbb: expose almost every clock in the bindings
clk: meson8b: expose every clock in the bindings
clk: meson: gxbb: fix protection against undefined clks
clk: meson: meson8b: fix protection against undefined clks
dt-bindings: clock: meson8b: describe the embedded reset controller
|
|
This patch switches to the stable UART bindings but also add the correct
gate clock to the non-AO UART nodes for GXBB and GXL SoCs.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
|
|
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
|
|
The latest change of compat_sys_sigpending in commit 8f13621abced
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621abced ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes: 1c6bd7173d66
Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+
|
|
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
|
|
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
|
|
We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
|
|
ext4_xattr_inode_read() currently reads each block sequentially while
waiting for io operation to complete before moving on to the next
block. This prevents request merging in block layer.
Add a ext4_bread_batch() function that starts reads for all blocks
then optionally waits for them to complete. A similar logic is used
in ext4_find_entry(), so update that code to use the new function.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
When an xattr block has a single reference, block is updated inplace
and it is reinserted to the cache. Later, a cache lookup is performed
to see whether an existing block has the same contents. This cache
lookup will most of the time return the just inserted entry so
deduplication is not achieved.
Running the following test script will produce two xattr blocks which
can be observed in "File ACL: " line of debugfs output:
mke2fs -b 1024 -I 128 -F -O extent /dev/sdb 1G
mount /dev/sdb /mnt/sdb
touch /mnt/sdb/{x,y}
setfattr -n user.1 -v aaa /mnt/sdb/x
setfattr -n user.2 -v bbb /mnt/sdb/x
setfattr -n user.1 -v aaa /mnt/sdb/y
setfattr -n user.2 -v bbb /mnt/sdb/y
debugfs -R 'stat x' /dev/sdb | cat
debugfs -R 'stat y' /dev/sdb | cat
This patch defers the reinsertion to the cache so that we can locate
other blocks with the same contents.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
|
|
ext4_alloc_file_blocks() does not use its mode parameter. Remove it.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
After commit 62d1034f53e3 ("fortify: use WARN instead of BUG for now"),
we get a warning about possible stack overflow from a memcpy that
was not strictly bounded to the size of the local variable:
inlined from 'ext4_mb_seq_groups_show' at fs/ext4/mballoc.c:2322:2:
include/linux/string.h:309:9: error: '__builtin_memcpy': writing between 161 and 1116 bytes into a region of size 160 overflows the destination [-Werror=stringop-overflow=]
We actually had a bug here that would have been found by the warning,
but it was already fixed last year in commit 30a9d7afe70e ("ext4: fix
stack memory corruption with 64k block size").
This replaces the fixed-length structure on the stack with a variable-length
structure, using the correct upper bound that tells the compiler that
everything is really fine here. I also change the loop count to check
for the same upper bound for consistency, but the existing code is
already correct here.
Note that while clang won't allow certain kinds of variable-length arrays
in structures, this particular instance is fine, as the array is at the
end of the structure, and the size is strictly bounded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The dir_nlink feature has been enabled by default for new ext4
filesystems since e2fsprogs-1.41 in 2008, and was automatically
enabled by the kernel for older ext4 filesystems since the
dir_nlink feature was added with ext4 in kernel 2.6.28+ when
the subdirectory count exceeded EXT4_LINK_MAX-1.
Automatically adding the file system features such as dir_nlink is
generally frowned upon, since it could cause the file system to not be
mountable on older kernel, thus preventing the administrator from
rolling back to an older kernel if necessary.
In this case, the administrator might also want to disable the feature
because glibc's fts_read() function does not correctly optimize
directory traversal for directories that use st_nlinks field of 1 to
indicate that the number of links in the directory are not tracked by
the file system, and could fail to traverse the full directory
hierarchy. Fortunately, in the past ten years very few users have
complained about incomplete file system traversal by glibc's
fts_read().
This commit also changes ext4_inc_count() to allow i_nlinks to reach
the full EXT4_LINK_MAX links on the parent directory (including "."
and "..") before changing i_links_count to be 1.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196405
Signed-off-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
I get a static checker warning:
fs/ext4/ext4.h:3091 ext4_set_de_type()
error: buffer overflow 'ext4_type_by_mode' 15 <= 15
It seems unlikely that we would hit this read overflow in real life, but
it's also simple enough to make the array 16 bytes instead of 15.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
ext4_find_unwritten_pgoff() does not properly handle a situation when
starting index is in the middle of a page and blocksize < pagesize. The
following command shows the bug on filesystem with 1k blocksize:
xfs_io -f -c "falloc 0 4k" \
-c "pwrite 1k 1k" \
-c "pwrite 3k 1k" \
-c "seek -a -r 0" foo
In this example, neither lseek(fd, 1024, SEEK_HOLE) nor lseek(fd, 2048,
SEEK_DATA) will return the correct result.
Fix the problem by neglecting buffers in a page before starting offset.
Reported-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
CC: stable@vger.kernel.org # 3.8+
|
|
This fixes a problem where the system gets stuck in a loop
unable to wakeup via power button in s2idle.
The problem happens because:
- press power button:
- system emits 0xc0 (power press), event ignored
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- set wakeup_mode to true
- system goes to s2idle
- press power button
- system emits 0xc0 (power press), wakeup_mode is true,
system wakes
- system emits 0xc1 (power release), event processed,
emited as KEY_POWER
- system goes to s2idle again
To avoid this situation, process the presses (which matches what
intel-hid does too).
Verified on an Dell XPS 9365
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"This series is larger than I would like to submit for -rc4. My
original intent were to sent it to either -rc2 or -rc3. Unfortunately,
due to my vacations, I got a lot of pending stuff after my return, and
had to do some biz trips, with prevented me to send this earlier.
Several fixes:
- some fixes at atomisp staging driver
- several gcc 7 warning fixes
- cleanup media SVG files, in order to fix PDF build on some distros
- fix random Kconfig build of venus driver
- some fixes for the venus driver
- some changes from semaphone to mutex in ngene's driver
- some locking fixes at dib0700 driver
- several fixes on ngene's driver and frontends to make it properly
support some new boards added on Kernel 4.13
- some fixes to CEC drivers
- omap_vout: vrfb: convert to dmaengine
- docs-rst: document EBUSY for VIDIOC_S_FMT
Please notice that the big diffstat changes here are at the SVG files.
Visually, the images look the same, but the file size is now a lot
smaller than before, and they don't use some XML tags that would cause
them to be badly parsed by some ImageMagick versions, or to require a
lot of memory by TeTex, with would break PDF output on some
distributions"
* tag 'media/v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (68 commits)
media: atomisp2: array underflow in imx_enum_frame_size()
media: atomisp2: array underflow in ap1302_enum_frame_size()
media: atomisp2: Array underflow in atomisp_enum_input()
media: platform: davinci: drop VPFE_CMD_S_CCDC_RAW_PARAMS
media: platform: davinci: return -EINVAL for VPFE_CMD_S_CCDC_RAW_PARAMS ioctl
media: venus: don't abuse dma_alloc for non-DMA allocations
media: venus: hfi: fix error handling in hfi_sys_init_done()
media: venus: fix compile-test build on non-qcom ARM platform
media: venus: mark PM functions as __maybe_unused
media: cec-notifier: small improvements
media: pulse8-cec: persistent_config should be off by default
media: cec: cec_transmit_attempt_done: ignore CEC_TX_STATUS_MAX_RETRIES
media: staging: atomisp: array underflow in ioctl
media: lirc: LIRC_GET_REC_RESOLUTION should return microseconds
media: svg: avoid too long lines
media: svg files: simplify files
media: selection.svg: simplify the SVG file
media: vimc: set id_table for platform drivers
media: staging: atomisp: disable warnings with cc-disable-warning
media: davinci: variable 'common' set but not used
...
|
|
We've changed the discard command handling into parallel manner.
But, in this change, I forgot decreasing the usage count of the bio
which was used to send discard request. I'm sorry about that.
Fixes: a015434480dc ("ext4: send parallel discards on commit completions")
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- LP87565: set the proper output level for direction_output.
- stm32: fix the kernel build by selecting the hierarchical irqdomain
symbol properly - this happens to be done in the pin control
framework but whatever, it had dependencies to GPIO so we need to
apply it here.
- Select the hierarchical IRQ domain also for Xgene.
- Fix wakeups to work on MXC.
- Fix up the device tree binding on Exar that went astray, also add the
right bindings.
- Fix the unwanted events for edges from the library.
- Fix the unbalanced chanined IRQ on the Tegra.
* tag 'gpio-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra: fix unbalanced chained_irq_enter/exit
gpiolib: skip unwanted events, don't convert them to opposite edge
gpio: exar: Use correct property prefix and document bindings
gpio: gpio-mxc: Fix: higher 16 GPIOs usable as wake source
gpio: xgene-sb: select IRQ_DOMAIN_HIERARCHY
pinctrl: stm32: select IRQ_DOMAIN_HIERARCHY instead of depends on
gpio: lp87565: Set proper output level and direction for direction_output
MAINTAINERS: Add entry for Whiskey Cove PMIC GPIO driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of critical fixes for changes introduce this merge window.
- The TI sci_clk_get() API was pretty broken and nobody noticed.
- There were some CPUfreq crashes on C.H.I.P devices because we
failed to propagate rates up the clk tree.
- Also, the Intel Atom PMC clk driver needs to mark a clk critical if
the firmware has it enabled already so that audio doesn't get
killed on Baytrail.
- Gemini devices have a dead serial console because the reset control
usage in the serial driver assume one method of reset that gemini
doesn't support (this will be fixed in the next version in the
reset framework so this is the small fix for -rc series).
- Finally we have two rate calculation fixes, one for Exynos and one
for Meson SoCs, that fix rate inconsistencies"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: keystone: sci-clk: Fix sci_clk_get
clk: meson: mpll: fix mpll0 fractional part ignored
clk: samsung: exynos5420: The EPLL rate table corrections
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
clk: x86: Do not gate clocks enabled by the firmware
clk: gemini: Fix reset regression
|
|
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"The recent irq core changes unearthed API abuse in the HPET code,
which manifested itself in a suspend/resume regression.
The fix replaces the cruft with the proper function calls and cures
the regression"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Cure interface abuse in the resume path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for a multiplication overflow in the timer code on 32bit
systems"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Fix overflow in get_next_timer_interrupt
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This comes a bit later than I planned, and as a consequence is a
larger than it should be.
Most of the changes are devicetree fixes, across lots of platforms:
Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.
Also across many platforms, I applied an older series of simple
randconfig build fixes. This includes making the CONFIG_MTD_XIP option
compile again, which had been broken for many years and probably has
not been missed, but it felt wrong to just remove it completely.
The only other changes are:
- We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
work out of the box.
- A few regression fixes for Texas Instruments OMAP2+.
- A boot regression fix for the Renesas regulator quirk.
- A suspend/resume fix for Uniphier SoCs, fixing the resume of the
system bus"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: dts: tango4: Request RGMII RX and TX clock delays
bus: uniphier-system-bus: set up registers when resuming
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
arm64: defconfig: enable missing HWSPINLOCK
ARM: pxa: select both FB and FB_W100 for eseries
ARM: ixp4xx: fix ioport_unmap definition
ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
ARM: mmp: mark usb_dma_mask as __maybe_unused
ARM: omap2: mark unused functions as __maybe_unused
ARM: omap1: avoid unused variable warning
ARM: sirf: mark sirfsoc_init_late as __maybe_unused
ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
ARM: omap1/ams-delta: warn about failed regulator enable
ARM: rpc: rename RAM_SIZE macro
ARM: w90x900: normalize clk API
ARM: ep93xx: normalize clk API
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some more arm64 fixes for 4.13. The main one is the PTE race
with the hardware walker, but there are a couple of other things too.
- Report correct timer frequency to userspace when trapping
CNTFRQ_EL0
- Fix race with hardware page table updates when updating access
flags
- Silence clang overflow warning in VA_START and PAGE_OFFSET
calculations"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: avoid overflow in VA_START and PAGE_OFFSET
arm64: Fix potential race with hardware DBM in ptep_set_access_flags()
arm64: Use arch_timer_get_rate when trapping CNTFRQ_EL0
|
|
Pull sparc fixes from David Miller:
- block interrupts properly across the entire MMU context change (both
the hw MMU context change and the TSB table change) so that we don't
get a perf event interrupt in the middle. From Rob Gardner.
- be sure to register hugepages early enough, from Nitin Gupta.
- UltraSPARC-III user copy exception handling would return garbage for
the copied length in some circumstances.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix exception handling in UltraSPARC-III memcpy.
sbus: Convert to using %pOF instead of full_name
sparc: defconfig: Cleanup from old Kconfig options
sparc64: Register hugepages during arch init
sparc64: Prevent perf from running during super critical sections
|
|
Pull ceph fixes from Ilya Dryomov:
"A bunch of fixes and follow-ups for -rc1 Luminous patches: issues with
->reencode_message() and last minute RADOS semantic changes in
v12.1.2"
* tag 'ceph-for-4.13-rc4' of git://github.com/ceph/ceph-client:
libceph: make RECOVERY_DELETES feature create a new interval
libceph: upmap semantic changes
crush: assume weight_set != null imples weight_set_size > 0
libceph: fallback for when there isn't a pool-specific choose_arg
libceph: don't call ->reencode_message() more than once per message
libceph: make encode_request_*() work with r_mempool requests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Now we hit the usual ASoC-fix-flood in the middle of release.
Most of the changes are trivial and device-specific, while one
significant change is the fix for unbalanced of_graph_*() refcounts.
This involved a change in the graph API itself that had been a bit
messy"
* tag 'sound-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix speaker output from VAIO VPCL14M1R
device property: Fix usecount for of_graph_get_port_parent()
ASoC: rt5665: fix wrong register for bclk ratio control
ASoC: Intel: Use MCLK instead of BLCK as the sysclock for RT5514 codec on kabylake platform
ASoC: Intel: Enabling ASRC for RT5663 codec on kabylake platform
ASoC: codecs: msm8916-analog: fix DIG_CLK_CTL_RXD3_CLK_EN define
ASoC: Intel: Skylake: Fix missing sentinels in sst_acpi_mach
ASoC: sh: hac: add missing "int ret"
ASoC: samsung: odroid: Fix EPLL frequency values
ASoC: sgtl5000: Use snd_soc_kcontrol_codec()
ASoC: rt5665: fix GPIO6 pin function define
ASoC: ux500: Restore platform DAI assignments
ASoC: fix pcm-creation regression
ASoC: do not close shared backend dailink
ASoC: pxa: SND_PXA2XX_SOC should depend on HAS_DMA
ASoC: Intel: Skylake: Fix default dma_buffer_size
ASoC: rt5663: Update the HW default values based on the shipping version
ASoC: imx-ssi: add check on platform_get_irq return value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- fix a scheduling-while-atomic bug in the AMD IOMMU driver. It was
found after the checker was enabled earlier.
- a fix for the virtual APIC code in the AMD IOMMU driver which
delivers device interrupts directly into KVM guests for assigned
devices.
- fixes for the recently merged lock-less page-table code for ARM. The
redundant TLB syncs got reverted and locks added again around the TLB
sync code.
- fix for error handling in arm_smmu_add_device()
- address sanitization fix for arm io-pgtable code
* tag 'iommu-fixes-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix schedule-while-atomic BUG in initialization code
iommu/amd: Enable ga_log_intr when enabling guest_mode
iommu/io-pgtable: Sanitise map/unmap addresses
iommu/arm-smmu: Fix the error path in arm_smmu_add_device
Revert "iommu/io-pgtable: Avoid redundant TLB syncs"
iommu/mtk: Avoid redundant TLB syncs locally
iommu/arm-smmu: Reintroduce locking around TLB sync operations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of mmc fixes intended for v4.13-rc4.
MMC core:
- Fix NULL pointer dereference for block I/O during hotplug
MMC host:
- sdhci-of-at91: Fix card detect for non-removable cards"
* tag 'mmc-v4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: bypass the queue even if usage is present for hotplug
mmc: sdhci-of-at91: force card detect value for non removable devices
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Either my email ate everything or everyone is on holidays, either way
all I can find is some lonely AMD fixes"
[ Europe might be on vacation, and the Pacific NW is too hot for work. ]
* tag 'drm-fixes-for-v4.13-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: Use list_del_init in amdgpu_mn_unregister
drm/amdgpu: Fix undue fallthroughs in golden registers initialization
drm/amdgpu: fix header on gfx9 clear state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes for recently merged code:
- a fix for the _PAGE_DEVMAP support, which was breaking KVM on
Power9 radix
- avoid a (harmless) lockdep warning in the early SMP code
- return failure for some uses of dma_set_mask() rather than falling
back to 32-bits
- fix stack setup in watchdog soft_nmi_common() to use emergency
stack
- fix of_irq_to_resource() error check in of_fsl_spi_probe()
Two fixes going to stable:
- fix saving of Transactional Memory SPRs in core dump
- fix __check_irq_replay missing decrementer interrupt
And two misc:
- fix 64-bit boot wrapper build with non-biarch compiler
- work around a POWER9 PMU hang after state-loss idle
Thanks to: Alistair Popple, Aneesh Kumar K.V, Cyril Bur, Gustavo
Romero, Jose Ricardo Ziviani, Laurent Vivier, Nicholas Piggin, Oliver
O'Halloran, Sergei Shtylyov, Suraj Jitindar Singh, Thomas Gleixner"
* tag 'powerpc-4.13-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix __check_irq_replay missing decrementer interrupt
powerpc/perf: POWER9 PMU stops after idle workaround
powerpc/83xx/mpc832x_rdb: fix of_irq_to_resource() error check
powerpc/64s: Fix stack setup in watchdog soft_nmi_common()
powerpc/powernv/pci: Return failure for some uses of dma_set_mask()
powerpc/boot: Fix 64-bit boot wrapper build with non-biarch compiler
powerpc/smp: Call smp_ops->setup_cpu() directly on the boot CPU
powerpc/tm: Fix saving of TM SPRs in core dump
powerpc/mm: Fix pmd/pte_devmap() on non-leaf entries
|
|
Mikael Pettersson reported that some test programs in the strace-4.18
testsuite cause an OOPS.
After some debugging it turns out that garbage values are returned
when an exception occurs, causing the fixup memset() to be run with
bogus arguments.
The problem is that two of the exception handler stubs write the
successfully copied length into the wrong register.
Fixes: ee841d0aff64 ("sparc64: Convert U3copy_{from,to}_user to accurate exception reporting.")
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Tested-by: Mikael Pettersson <mikpelinux@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patchadds the clock binding entry for the CEC 32K AO Clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
