| Age | Commit message (Collapse) | Author |
|---|
|
Check the AFU state whenever an API is called. The hypervisor may
issue a reset of the adapter when it detects a fault. When it happens,
it launches an error recovery which will either move the AFU to a
permanent failure state, or in the disabled state.
If the AFU is found to be disabled, detach all existing contexts from
it before issuing a AFU reset to re-enable it.
Before detaching contexts, notify any kernel driver through the EEH
callbacks of the AFU pci device.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Like on bare-metal, the cxl driver creates a virtual PHB and a pci
device for the AFU. The configuration space of the device is mapped to
the configuration record of the AFU.
Reuse the code defined in afu_cr_read8|16|32() when reading the
configuration space of the AFU device.
Even though the (virtual) AFU device is a pci device, the adapter is
not. So a driver using the cxl kernel API cannot read the VPD of the
adapter through the usual PCI interface. Therefore, we add a call to
the cxl kernel API:
ssize_t cxl_read_adapter_vpd(struct pci_dev *dev, void *buf, size_t count);
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add new entry point to scan the device tree at boot in a guest,
looking for cxl devices.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The new flash.c file contains the logic to flash a new image on the
adapter, through a hcall. It is an iterative process, with chunks of
data of 1M at a time. There are also 2 phases: write and verify. The
flash operation itself is driven from a user-land tool.
Once flashing is successful, an rtas call is made to update the device
tree with the new properties values for the adapter and the AFU(s)
Add a new char device for the adapter, so that the flash tool can
access the card, even if there is no valid AFU on it.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Filter out a few adapter parameters which don't make sense in a guest.
Document the changes.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The new of.c file contains code to parse the device tree to find out
about cxl adapters and AFUs.
guest.c implements the guest-specific callbacks for the backend API.
The process element ID is not known until the context is attached, so
we have to separate the context ID assigned by the cxl driver from the
process element ID visible to the user applications. In bare-metal,
the 2 IDs match.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
[mpe: Fix SMP=n build, fix PSERIES=n build, minor whitespace fixes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Introduce sub-structures containing the bare-metal specific fields in
the structures describing the adapter (struct cxl) and AFU (struct
cxl_afu).
Update all their references.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The hypervisor calls provide an interface with a coherent platform
facility and function. It matches version 0.16 of the 'PAPR changes'
document.
The following hcalls are supported:
H_ATTACH_CA_PROCESS Attach a process element to a coherent platform
function.
H_DETACH_CA_PROCESS Detach a process element from a coherent
platform function.
H_CONTROL_CA_FUNCTION Allow the partition to manipulate or query
certain coherent platform function behaviors.
H_COLLECT_CA_INT_INFO Collect interrupt info about a coherent.
platform function after an interrupt occurred
H_CONTROL_CA_FAULTS Control the operation of a coherent platform
function after a fault occurs.
H_DOWNLOAD_CA_FACILITY Support for downloading a base adapter image to
the coherent platform facility, and for
validating the entire image after the download.
H_CONTROL_CA_FACILITY Allow the partition to manipulate or query
certain coherent platform facility behaviors.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The hcalls introduced for cxl use a possible new value:
H_STATE (invalid state).
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The PSL interrupt cannot be multiplexed in a guest, as it is not
supported by the hypervisor. So an interrupt will be allocated
for it for each context. It will still be the first interrupt found in
the first interrupt range, but is treated almost like any other AFU
interrupt when creating/deleting the context. Only the handler is
different. Rework the code so that the range 0 is treated like the
other ranges.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The context parameter when calling cxl_irq() should be strongly typed.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
A few functions are mostly common between bare-metal and guest and
just need minor tuning. To avoid crowding the backend API, introduce a
few 'if' based on the CPU being in HV mode.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Rename a few functions, changing the 'cxl_' prefix to either
'cxl_pci_' or 'cxl_native_', to make clear that the implementation is
bare-metal specific.
Those functions will have an equivalent implementation for a guest in
a later patch.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The backend API (in cxl.h) lists some low-level functions whose
implementation is different on bare-metal and in a guest. Each
environment implements its own functions, and the common code uses
them through function pointers, defined in cxl_backend_ops
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
CXL kernel API was defining the process problem state area during
context initialization, making it possible to map the problem state
area before attaching the context. This won't work on a powerVM
guest. So force the logical behavior, like in userspace: attach first,
then map the problem state area.
Remove calls to cxl_assign_psn_space during init. The function is
already called on the attach paths.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Move a few functions around to better separate code specific to
bare-metal environment from code which will be commonly used between
guest and bare-metal.
Code specific to bare-metal is meant to be in native.c or pci.c
only. It's basically anything which touches the card p1 registers,
some p2 registers not needed from a guest and the PCI interface.
Co-authored-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Move around some functions which will be accessed from the bare-metal
and guest environments.
Code in native.c and pci.c is meant to be bare-metal specific.
Other files contain code which may be shared with guests.
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
In eeh_pci_enable(), after making the request to set the new options, we
call eeh_ops->wait_state() to check that the request finished successfully.
At the moment, if eeh_ops->wait_state() returns 0, we return 0 without
checking that it reflects the expected outcome. This can lead to callers
further up the chain incorrectly assuming the slot has been successfully
unfrozen and continuing to attempt recovery.
On powernv, this will occur if pnv_eeh_get_pe_state() or
pnv_eeh_get_phb_state() return 0, which in turn occurs if the relevant OPAL
call returns OPAL_EEH_STOPPED_MMIO_DMA_FREEZE or
OPAL_EEH_PHB_ERROR respectively.
On pseries, this will occur if pseries_eeh_get_state() returns 0, which in
turn occurs if RTAS reports that the PE is in the MMIO Stopped and DMA
Stopped states.
Obviously, none of these cases represent a successful completion of a
request to thaw MMIO or DMA.
Fix the check so that a wait_state() return value of 0 won't be considered
successful for the EEH_OPT_THAW_MMIO or EEH_OPT_THAW_DMA cases.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When eeh_dump_pe_log() is only called by eeh_slot_error_detail(),
we already have the check that the PE isn't in PCI config blocked
state in eeh_slot_error_detail(). So we needn't the duplicated
check in eeh_dump_pe_log().
This removes the duplicated check in eeh_dump_pe_log(). No logical
changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When passing through SRIOV VFs to guest, we possibly encounter EEH
error on PF. In this case, the VF PEs are put into frozen state.
The error could be reported to guest before it's captured by the
host. That means the guest could attempt to recover errors on VFs
before host gets chance to recover errors on PFs. The VFs won't be
recovered successfully.
This enforces the recovery order for above case: the recovery on
child PE in guest is hold until the recovery on parent PE in host
is completed.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When we have partial hotplug as part of the error recovery on PF,
the VFs that are bound with vfio-pci driver will experience hotplug.
That's not allowed.
This checks if the VF PE is passed or not. If it does, we leave
the VF without removing it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When EEH error happened to the parent PE of those PEs that have
been passed through to guest, the error is propagated to guest
domain and the VFIO driver's error handlers are called. It's not
correct as the error in the host domain shouldn't be propagated
to guests and affect them.
This adds one more limitation when calling EEH error handlers.
If the PE has been passed through to guest, the error handlers
won't be called.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PFs are enumerated on PCI bus, while VFs are created by PF's driver.
In EEH recovery, it has two cases:
1. Device and driver is EEH aware, error handlers are called.
2. Device and driver is not EEH aware, un-plug the device and plug it again
by enumerating it.
The special thing happens on the second case. For a PF, we could use the
original pci core to enumerate the bus, while for VF we need to record the
VFs which aer un-plugged then plug it again.
Also The patch caches the VF index in pci_dn, which can be used to
calculate VF's bus, device and function number. Those information helps to
locate the VF's PCI device instance when doing hotplug during EEH recovery
if necessary.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
After PE reset, OPAL API opal_pci_reinit() is called on all devices
contained in the PE to reinitialize them. While skiboot is not aware of
VFs, we have to implement the function in kernel to reinitialize VFs after
reset on PE for VFs.
In this patch, two functions pnv_pci_fixup_vf_mps() and
pnv_eeh_restore_vf_config() both manipulate the MPS of the VF, since for a
VF it has three cases.
1. Normal creation for a VF
In this case, pnv_pci_fixup_vf_mps() is called to make the MPS a proper
value compared with its parent.
2. EEH recovery without VF removed
In this case, MPS is stored in pci_dn and pnv_eeh_restore_vf_config() is
called to restore it and reinitialize other part.
3. EEH recovery with VF removed
In this case, VF will be removed then re-created. Both functions are
called. First pnv_pci_fixup_vf_mps() is called to store the proper MPS
to pci_dn and then pnv_eeh_restore_vf_config() is called to do proper
thing.
This introduces two functions: pnv_pci_fixup_vf_mps() to fixup the VF's
MPS to make sure it is equal to parent's and store this value in pci_dn
for future use. pnv_eeh_restore_vf_config() to re-initialize on VF by
restoring MPS, disabling completion timeout, enabling SERR, etc.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PEs for VFs don't have primary bus. So they have to have their own reset
backend, which is used during EEH recovery. The patch implements the reset
backend for VF's PE by issuing FLR or AF FLR to the VFs, which are contained
in the PE.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This creates PEs for VFs in the weak function pcibios_bus_add_device().
Those PEs for VFs are identified with newly introduced flag EEH_PE_VF
so that we treat them differently during EEH recovery.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
VFs and their corresponding pdn are created and released dynamically
when their PF's SRIOV capability is enabled and disabled. This creates
and releases EEH devices for VFs when creating and releasing their pdn
instances, which means EEH devices and pdn instances have same life
cycle. Also, VF's EEH device is identified by (struct eeh_dev::physfn).
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This restricts the EEH address cache to use only the first 7 BARs. This
makes __eeh_addr_cache_insert_dev() ignore PCI bridge window and IOV BARs.
As the result of this change, eeh_addr_cache_get_dev() will return VFs from
VF's resource addresses instead of parent PFs.
This also removes PCI bridge check as we limit __eeh_addr_cache_insert_dev()
to 7 BARs and this effectively excludes PCI bridges from being cached.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
As commit ac205b7bb72f ("PCI: make sriov work with hotplug remove")
indicates, VFs which is on the same PCI bus as their PF, should be
removed before the PF. Otherwise, we might run into kernel crash
at PCI unplugging time.
This applies the above pattern to powerpc PCI hotplug path.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds weak function pcibios_bus_add_device() for arch dependent
code could do proper setup. For example, powerpc could setup EEH
related resources for SRIOV VFs.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
During EEH recovery, hotplug is applied to the devices which don't
have drivers or their drivers don't support EEH. However, the hotplug,
which was implemented based on PCI bus, can't be applied to VF directly.
Instead, we unplug and plug individual PCI devices (VFs).
This renames virtn_{add,remove}() and exports them so they can be used
in PCI hotplug during EEH recovery.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The original implementation is ugly: unnecessary if statements and
"out" tag. This reworks the function to avoid above weaknesses. No
functional changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
No code changes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
No code changes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We don't need to update linux page table entry with _PAGE_HASHPTE early
in hash pte fault. A parallel pte update will loop via _PAGE_BUSY
and look at _PAGE_HASHPTE for a required hpte flush only if
_PAGE_BUSY is cleared. That ensures a pte update will wait for a
parallel hpte insert to finish before looking at _PAGE_HASHPTE bit.
To avoid further confusion drop setting _PAGE_HASHPTE in cmpxchg in __hash_page_4K.
commit 41743a4e34f0 ("powerpc: Free a PTE bit on ppc64 with 64K pages")
did similar change for 64K config
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We are updating pte in those functions.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
With next generation power processor, we are having a new mmu model
[1] that require us to maintain a different linux page table format.
Inorder to support both current and future ppc64 systems with a single
kernel we need to make sure kernel can select between different page
table format at runtime. With the new MMU (radix MMU) added, we will
have two different pmd hugepage size 16MB for hash model and 2MB for
Radix model. Hence make HPAGE_PMD related values as a variable.
Actual conversion of HPAGE_PMD to a variable for ppc64 happens in a
followup patch.
[1] http://ibm.biz/power-isa3 (Needs registration).
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This is needed so that we can support both hash and radix page table
using single kernel. Radix kernel uses a 4 level table.
We now use physical address in upper page table tree levels. Even though
they are aligned to their size, for the masked bits we use the
bit positions as per PowerISA 3.0.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We remove real_pte_t out of STRICT_MM_TYPESCHECK.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
We move the page table accessors into a separate header. We will
later add a big endian variant of the table which is needed for radix.
No functionality change only code movement.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch adds the ability to be able to save the VSX registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.
This patch builds on a previous optimisation for the FPU and VEC registers
in the thread copy path to avoid a possibly pointless reload of VSX state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch adds the ability to be able to save the VEC registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.
This patch builds on a previous optimisation for the FPU registers in the
thread copy path to avoid a possibly pointless reload of VEC state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch adds the ability to be able to save the FPU registers to the
thread struct without giving up (disabling the facility) next time the
process returns to userspace.
This patch optimises the thread copy path (as a result of a fork() or
clone()) so that the parent thread can return to userspace with hot
registers avoiding a possibly pointless reload of FPU register state.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This prepares for the decoupling of saving {fpu,altivec,vsx} registers and
marking {fpu,altivec,vsx} as being unused by a thread.
Currently giveup_{fpu,altivec,vsx}() does both however optimisations to
task switching can be made if these two operations are decoupled.
save_all() will permit the saving of registers to thread structs and leave
threads MSR with bits enabled.
This patch introduces no functional change.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently the FPU, VEC and VSX facilities are lazily loaded. This is not
a problem unless a process is using these facilities.
Modern versions of GCC are very good at automatically vectorising code,
new and modernised workloads make use of floating point and vector
facilities, even the kernel makes use of vectorised memcpy.
All this combined greatly increases the cost of a syscall since the
kernel uses the facilities sometimes even in syscall fast-path making it
increasingly common for a thread to take an *_unavailable exception soon
after a syscall, not to mention potentially taking all three.
The obvious overcompensation to this problem is to simply always load
all the facilities on every exit to userspace. Loading up all FPU, VEC
and VSX registers every time can be expensive and if a workload does
avoid using them, it should not be forced to incur this penalty.
An 8bit counter is used to detect if the registers have been used in the
past and the registers are always loaded until the value wraps to back
to zero.
Several versions of the assembly in entry_64.S were tested:
1. Always calling C.
2. Performing a common case check and then calling C.
3. A complex check in asm.
After some benchmarking it was determined that avoiding C in the common
case is a performance benefit (option 2). The full check in asm (option
3) greatly complicated that codepath for a negligible performance gain
and the trade-off was deemed not worth it.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Move load_vec in the struct to fill an existing hole, reword change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fixup
|
|
Currently when threads get scheduled off they always giveup the FPU,
Altivec (VMX) and Vector (VSX) units if they were using them. When they are
scheduled back on a fault is then taken to enable each facility and load
registers. As a result explicitly disabling FPU/VMX/VSX has not been
necessary.
Future changes and optimisations remove this mandatory giveup and fault
which could cause calls such as clone() and fork() to copy threads and run
them later with FPU/VMX/VSX enabled but no registers loaded.
This patch starts the process of having MSR_{FP,VEC,VSX} mean that a
threads registers are hot while not having MSR_{FP,VEC,VSX} means that the
registers must be loaded. This allows for a smarter return to userspace.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Load up the non volatile FPU and VMX regs and ensure that they are the
expected value in a signal handler
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Loop in assembly checking the registers with many threads.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Test that the non volatile floating point and Altivec registers get
correctly preserved across the fork() syscall.
fork() works nicely for this purpose, the registers should be the same for
both parent and child
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Add include guards to basic_asm.h, minor formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
LTO can cause GCC to inline some functions which have attributes set.
The act of inlining the functions can lead to GCC forgetting about the
attributes which leads to incorrect tests.
Notable example being: __attribute__((__target__("no-vsx")))
LTO can also interact strangely with custom assembly functions and cause
tests to intermittently fail.
Both these cases are hard to detect and require manual inspection of
binaries which is unlikely to happen for all tests. Furthermore, LTO
optimisations are not necessary for selftests and correctness is
paramount and as such it is best to disable LTO.
LTO can be enabled on a per test basis.
A pseries_le_defconfig kernel on a POWER8 was used to determine that the
same subset of selftests pass and fail with and without -flto in the
common Makefile.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
