| Age | Commit message (Collapse) | Author |
|---|
|
peernet2id_alloc() is racy without rtnl_lock() as refcount_read(&peer->count)
under net->nsid_lock does not guarantee, peer is alive:
rcu_read_lock()
peernet2id_alloc() ..
spin_lock_bh(&net->nsid_lock) ..
refcount_read(&peer->count) (!= 0) ..
.. put_net()
.. cleanup_net()
.. for_each_net(tmp)
.. spin_lock_bh(&tmp->nsid_lock)
.. __peernet2id(tmp, net) == -1
.. ..
.. ..
__peernet2id_alloc(alloc == true) ..
.. ..
rcu_read_unlock() ..
.. synchronize_rcu()
.. kmem_cache_free(net)
After the above situation, net::netns_id contains id pointing to freed memory,
and any other dereferencing by the id will operate with this freed memory.
Currently, peernet2id_alloc() is used under rtnl_lock() everywhere except
ovs_vport_cmd_fill_info(), and this race can't occur. But peernet2id_alloc()
is generic interface, and better we fix it before someone really starts
use it in wrong context.
v2: Don't place refcount_read(&net->count) under net->nsid_lock
as suggested by Eric W. Biederman <ebiederm@xmission.com>
v3: Rebase on top of net-next
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jason Wang says:
====================
tun: allow to attach eBPF filter
This series tries to implement eBPF socket filter for tun. This could
be used for implementing efficient virtio-net receive filter for
vhost-net.
Changes from V2:
- fix typo
- remove unnecessary double check
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows userspace to attach eBPF filter to tun. This will
allow to implement VM dataplane filtering in a more efficient way
compared to cBPF filter by allowing either qemu or libvirt to
attach eBPF filter to tun.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be reused by other eBPF program other than queue selection.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
net: sched: allow qdiscs to share filter block instances
Currently the filters added to qdiscs are independent. So for example if you
have 2 netdevices and you create ingress qdisc on both and you want to add
identical filter rules both, you need to add them twice. This patchset
makes this easier and mainly saves resources allowing to share all filters
within a qdisc - I call it a "filter block". Also this helps to save
resources when we do offload to hw for example to expensive TCAM.
So back to the example. First, we create 2 qdiscs. Both will share
block number 22. "22" is just an identification:
$ tc qdisc add dev ens7 ingress_block 22 ingress
^^^^^^^^^^^^^^^^
$ tc qdisc add dev ens8 ingress_block 22 ingress
^^^^^^^^^^^^^^^^
If we don't specify "block" command line option, no shared block would
be created:
$ tc qdisc add dev ens9 ingress
Now if we list the qdiscs, we will see the block index in the output:
$ tc qdisc
qdisc ingress ffff: dev ens7 parent ffff:fff1 ingress_block 22
qdisc ingress ffff: dev ens8 parent ffff:fff1 ingress_block 22
qdisc ingress ffff: dev ens9 parent ffff:fff1
To make is more visual, the situation looks like this:
ens7 ingress qdisc ens7 ingress qdisc
| |
| |
+----------> block 22 <----------+
Unlimited number of qdiscs may share the same block.
Note that this patchset introduces block sharing support also for clsact
qdisc:
$ tc qdisc add dev ens10 ingress_block 23 egress_block 24 clsact
$ tc qdisc show dev ens10
qdisc clsact ffff: dev ens10 parent ffff:fff1 ingress_block 23 egress_block 24
We can add filter using the block index:
$ tc filter add block 22 protocol ip pref 25 flower dst_ip 192.168.0.0/16 action drop
Note we cannot use the qdisc for filter manipulations of shared blocks:
$ tc filter add dev ens8 ingress protocol ip pref 1 flower dst_ip 192.168.100.2 action drop
Error: This filter block is shared. Please use the block index to manipulate the filters.
We will see the same output if we list filters for ingress qdisc of
ens7 and ens8, also for the block 22:
$ tc filter show block 22
filter block 22 protocol ip pref 25 flower chain 0
filter block 22 protocol ip pref 25 flower chain 0 handle 0x1
...
$ tc filter show dev ens7 ingress
filter block 22 protocol ip pref 25 flower chain 0
filter block 22 protocol ip pref 25 flower chain 0 handle 0x1
...
$ tc filter show dev ens8 ingress
filter block 22 protocol ip pref 25 flower chain 0
filter block 22 protocol ip pref 25 flower chain 0 handle 0x1
...
---
v10->v11:
- patch 2:
- fixed error path when register_pernet_subsys fails pointed out by Cong
- patch 9:
- rebased on top of the current net-next
v9->v10:
- patch 7:
- fixed ifindex magic in the patch description
- userspace patches:
- added manpages and patch descriptions
v8->v9:
- patch "net: sched: add rt netlink message type for block get" was
removed, userspace check filter existence using qdisc dump
v7->v8:
- patch 7:
- added comment to ifindex block magic
- patch 9:
- new patch
- patch 10:
- base this on the patch that introduces qdisc-generic block index
attributes parsing/dumping
- patch 13:
- rebased on top of current net-next
v6->v7:
- patch 1:
- unsquashed shared block patch that was previously squashed by mistake
- fixed error path in block create - freeing chain 0
- patch 2:
- new patch - splitted from the previous one as it got accidentaly
squashed in the rebasing process in the past
- converted to idr extended
- removed auto-generating of block indexes. Callers have to explicily
tell that the block is shared by passing non-zero block index
- fixed error path in block get ext - freeing chain 0
- patch 7:
- changed extack message for block index handle as suggested by DaveA
- added extack message when block index does not exist
- the block ifindex magic is in define and change to 0xffffffff
as suggested by Jamal
- patch 8:
- new patch implementing RTM_GETBLOCK in order to query if the block
with some index exists
- patch 9:
- adjust to the core changes and check block index attributes for being 0
v5->v6:
- added patch 6 that introduces block handle
v4->v5:
- patch 5:
- add tracking of binding of devs that are unable to offload and check
that before block cbs call.
v3->v4:
- patch 1:
- rebased on top of the current net-next
- added some extack strings
- patch 3:
- rebased on top of the current net-next
- patch 5:
- propagate netdev_ops->ndo_setup_tc error up to tcf_block_offload_bind
caller
- patch 7:
- rebased on top of the current net-next
v2->v3:
- removed original patch 1, removing tp->q cls_bpf dependency. Fixed by
Jakub in the meantime.
- patch 1:
- rebased on top of the current net-next
- patch 5:
- new patch
- patch 8:
- removed "p_" prefix from block index function args
- patch 10:
- add tc offload feature handling
====================
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to convert from mlxsw_sp_port to net_device and back again.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Benefit from the prepared TC and in-driver ACL infrastructure and
introduce block sharing offload. For that, a new struct "block" is
introduced in spectrum_acl in order to hold a list of specific
block-port bindings.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead, pass netdev and ingress flag to ruleset unbind op.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to prepare for follow-up changes, make the bind/unbind helpers
very simple. That required move of ht insertion/removal and bind/unbind
calls into mlxsw_sp_acl_ruleset_create/destroy.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Benefit from the previously introduced shared filter blocks
infrastructure and allow ingress and clsact qdisc instances to share
filter blocks. The block index is coming from userspace as qdisc option.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce two new attributes to be used for qdisc creation and dumping.
One for ingress block, one for egress block. Introduce a set of ops that
qdisc which supports block sharing would implement.
Passing block indexes in qdisc change is not supported yet and it is
checked and forbidded.
In future, these attributes are to be reused for specifying block
indexes for classes as well. As of this moment however, it is not
supported so a check is in place to forbid it.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the tcm_ifindex with value TCM_IFINDEX_MAGIC_BLOCK is invalid ifindex,
use it to indicate that we work with block, instead of qdisc.
So if tcm_ifindex is set to TCM_IFINDEX_MAGIC_BLOCK, tcm_parent is used
to carry block_index.
If the block is set to be shared between at least 2 qdiscs, it is
forbidden to use the qdisc handle to add/delete filters. In that case,
userspace has to pass block_index.
Also, for dump of the filters, in case the block is shared in between at
least 2 qdiscs, the each filter is dumped with tcm_ifindex value
TCM_IFINDEX_MAGIC_BLOCK and tcm_parent set to block_index. That gives
the user clear indication, that the filter belongs to a shared block
and not only to one qdisc under which it is dumped.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During block bind, we need to check tc offload feature. If it is
disabled yet still the block contains offloaded filters, forbid the
bind. Also forbid to register callback for a block that already
contains offloaded filters, as the play back is not supported now.
For keeping track of offloaded filters there is a new counter
introduced, alongside with couple of helpers called from cls_* code.
These helpers set and clear TCA_CLS_FLAGS_IN_HW flag.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both are no longer used, so remove them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Couple of classifiers call netif_keep_dst directly on q->dev. That is
not possible to do directly for shared blocke where multiple qdiscs are
owning the block. So introduce a infrastructure to keep track of the
block owners in list and use this list to implement block variant of
netif_keep_dst.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use block index in the messages instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow qdiscs to share filter blocks among them. Each qdisc type has to
use block get/put extended modifications that enable sharing.
Shared blocks are tracked within each net namespace and identified
by u32 index. This index is passed from user during the qdisc creation.
If user passes index that is not used by any other qdisc, new block
is created. If user passes index that is already used, the existing
block will be re-used.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far, there was possible only to register a single filter chain
pointer to block->chain[0]. However, when the blocks will get shareable,
we need to allow multiple filter chain pointers registration.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
bnxt_en: Updates for net-next.
First, we upgrade the firmware interface spec. Due to a change in
the toolchains, the auto-generated bnxt_hsi.h does not match the
old bnxt_hsi.h and the patch is really big. This should be just
one-time. Going forward, changes should be incremental.
The next 10 patches implement a new scheme for the PF and VF drivers
to allocate and reserve resources. The new scheme is more flexible
and allows dynamic and asymmetric distribution of resources, whereas
the old scheme is static and even distribution.
The last few patches add cacheline size setting, a couple of PCI IDs,
better management of VF MAC address, and a better parent switchdev ID
for dual-port devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the driver exports different switchdev PARENT_IDs for
representors belonging to different SR-IOV PF-pools of an adapter.
This is not correct as the adapter can switch across all vports
of an adapter. This patch fixes this by exporting a common switchdev
PARENT_ID for all reps of an adapter. The PCIE DSN is used as the id.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chip supports 64-byte and 128-byte cache line size for more optimal
DMA performance when matched to the CPU cache line size. The default is 64.
If the system is using 128-byte cache line size, set it to 128.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Forward hwrm_func_vf_cfg command from VF to PF driver, to store
VF MAC address in PF's context. This will allow "ip link show"
to display all VF MAC addresses.
Maintain 2 locations of MAC address in VF info structure, one for
a PF assigned MAC and one for VF assigned MAC.
Display VF assigned MAC in "ip link show", only if PF assigned MAC is
not valid.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_check_rings() is called by ethtool, XDP setup, and ndo_setup_tc()
to see if there are enough resources to support the new configuration.
Expand the call to test all resources if the firmware supports the new
API. With the more flexible resource allocation scheme, this call must
be made to check that all resources are available before committing to
allocate the resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of the old method of evenly dividing the resources to the VFs,
use the new firmware API to specify min and max resources for each VF.
This way, there is more flexibility for each VF to allocate more or less
resources.
The min is the absolute minimum for each VF to function. The max is the
global resources minus the resources used by the PF. Each VF is
guaranteed the min. Up to max resources may be available for some VFs.
The PF driver can use one of 2 strategies specified in NVRAM to assign
the resources. The old legacy strategy of evenly dividing the resources
or the new flexible strategy.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_rfs_capable(), add call to reserve vnic resources to support
NTUPLE. Return true if we can successfully reserve enough vnics.
Otherwise, reserve the minimum 1 VNIC for normal operations not
supporting NTUPLE and return false.
Also, suppress warning message about not enough resources for NTUPLE when
only 1 RX ring is in use. NTUPLE filters by definition require multiple
RX rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new method will call firmware to reserve the desired tx, rx, cmpl
rings, ring groups, stats context, and vnic resources. A second query
call will check the actual resources that firmware is able to reserve.
The driver will then trim and adjust based on the actual resources
provided by firmware. The driver will then reserve the final resources
in use.
This method is a more flexible way of using hardware resources. The
resources are not fixed and can by adjusted by firmware. The driver
adapts to the available resources that the firmware can reserve for
the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In combined mode, the driver is currently not setting RX and TX ring
numbers the same when firmware can allocate more RX than TX or vice versa.
This will confuse the user as the ethtool convention assumes they are the
same in combined mode. Fix it by adding bnxt_trim_dflt_sh_rings() to trim
RX and TX ring numbers to be the same as the completion ring number in
combined mode.
Note that if TCs are enabled and/or XDP is enabled, the number of TX rings
will not be the same as RX rings in combined mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new API HWRM_FUNC_RESOURCE_QCAPS provides min and max hardware
resources. Use the new API when it is supported by firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources. This new structure is common for PFs and VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After SRIOV has been enabled and disabled, the MSIX vectors assigned to
the VFs have to be re-initialized. Otherwise they cannot be re-used by
the PF. For example, increasing the number of PF rings after disabling
SRIOV may fail if the PF uses MSIX vectors previously assigned to the VFs.
To fix this, we add logic in bnxt_restore_pf_fw_resources() to close the
NIC, clear and re-init MSIX, and re-open the NIC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new __bnxt_close_nic() function to do all the work previously done
in bnxt_close_nic() except waiting for SRIOV configuration. The new
function will be used in the next patch as part of SRIOV cleanup.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The version has new firmware APIs to allocate PF/VF resources more
flexibly.
New toolchains were used to generate this file, resulting in a one-time
large diffstat.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Martin Blumenstingl says:
====================
dwmac-meson8b: clock fixes for Meson8b
this series is now successfully tested, thus we think it's ready to be
applied to your net-next tree.
Emiliano reported [0] that he couldn't get dwmac-meson8b to work on his
Odroid-C1. This is the (hopefully) final version of this series, which
was successfully tested.
Due to the fact that the public S805/S905/S912 datasheets all seem to
be outdated regarding the description of the PRG_ETH0 (also called
PRG_ETHERNET_ADDR0) register Linus Lüssing offered to help testing with
an oscilloscope and an Odroid-C1. I would like to say HUGE thanks to him
at this point as he spent hours figuring out the effects of the bits
that are (though to be) relevant to get Ethernet working on the
Odroid-C1.
We tested three scenarios, all based on version 3 of this series:
1) MPLL2 at ~500MHz, m250_div set to 1, bit 10 enabled
this resulted in a clock rate twice as high as expected at the RGMII TX
clock pin (250MHz instead of 125MHz for Gbit connections and 50MHz
instead of 25MHz for 100Mbit/s connections). it did not change the
rate at the XTAL_IN pin of PHY (which stayed consistenly at 25MHz)
2) MPLL2 at ~250MHz, m250_div set to 1, bit 10 disabled
the oscilloscope shows "no clock" for the RGMII TX clock pin at it's
highest resolution (and random rates at lower resolutions). XTAL_IN is
still at 25MHz
3) MPLL2 at ~250MHz, m250_div set to 1, bit 10 enabled
this resulted in a 125MHz signal at the RGMII TX clock pin for Gbit
speeds and 25MHz for 100Mbit/s - both values are as expected. The rate
on the XTAL_IN pin was at 25MHz
-> boot-logs (with the PRG_ETH0 register value) and screenshots from the
readings of the oscilloscope can be found at:
https://metameute.de/~tux/linux/amlogic/odroidc1/ethernet/
Version 4 of this series is based on the results from Linus Lüssing's
help with the oscilloscope and Odroid-C1.
Unfortunately I don't have any Meson8b boards with RGMII PHY so I could
only partially test this. @Emiliano: Could you please give this version
a try and let me know about the results (preferably with a "Tested-by"
if it works)?
You obviously still need your two "ARM: dts: meson8b" patches which
- add the amlogic,meson8b-dwmac" compatible to meson8b.dtsi
- enable Ethernet on the Odroid-C1 (according to your last thest a TX
delay of 4ns is required to make it work properly)
When testing on Meson8b this also needs a fix for the MPLL clock driver:
"clk: meson: mpll: use 64-bit maths in params_from_rate", see:
https://patchwork.kernel.org/patch/10131677/
I have tested this myself on a Khadas VIM (GXL SoC, internal RMII PHY)
and a Khadas VIM2 (GXM SoC, external RGMII PHY). Both are still working
fine (so let's hope that this also fixes your Meson8b issue :)).
changes since v4 at [4]:
- dropped "RFT" status since Jerome tested this series successfully!
- dropped PATCH #2 ("simplify generating the clock names"). I will
improve the whole clock registration in a separate series. since that
patch didn't really improve anything I dropped it for now
- added Jerome's Acked-/Reviewed-/Tested-by's - many thanks!
changes since v3 at [3]:
- renamed the function PATCH #1 from meson8b_init_rgmii_clk to
meson8b_init_rgmii_tx_clk since we now know what the register bits
mean
- rewrote PATCH #3 because bit 10 is a gate clock and it seems that
there is an internal fixed divide-by-2 clock. see the patch
description for a detailed explanation
- updated the description of PATCH #4 and #5 as the clock we're trying
to fix is the "RGMII TX" clock (old version stated that this is the
"RGMII clock" or "PHY reference clock"). also updated the numbers in
the description now that we have the clock hierarchy right (at least
we hope so)
changes since v2 at [2]:
- added PATCH #2 to make the following patch easier
- Emiliano reported that there's currently another bug in the
dwmac-meson8b driver which prevents it from working with RGMII PHYs on
Meson8b: bit 10 of the PRG_ETH0 register is configures a clock gate
(instead of a divide by 5 or divide by 10 clock divider). This has not
been visible on GXBB and later due to the input clock which always led
to a selection of "divide by 10" (which is done internally in the IP
block, but the bit actually means "enable RGMII clock output").
PATCH #3 was added to address this issue.
- the commit message of PATCH #4 and #5 (formerly PATCH #2 and #3) were
updated and the patch itself rebased because the m25_div clock was
removed with the new PATCH #3 (so some of the statements were not
valid anymore)
changes since v1 at [1]:
- changed the subject of the cover-letter to indicate that this is all
about the RGMII clock
- added PATCH #1 which ensures that we don't unnecessarily change the
parent clocks in RMII mode (and also makes the code easier to
understand)
- changed subject of PATCH #2 (formerly PATCH #1) to state that this
is about the RGMII clock
- added Jerome's Reviewed-by to PATCH #2 (formerly PATCH #1)
- replaced PATCH #3 (formerly PATCH #2) with one that sets
CLK_SET_RATE_PARENT on the mux and thus re-configures the MPLL2 clock
on Meson8b correctly
[0] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005596.html
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005848.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005861.html
[3] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005899.html
[4] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006125.html
====================
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Meson8b the only valid input clock is MPLL2. The bootloader
configures that to run at 500002394Hz which cannot be divided evenly
down to 125MHz using the m250_div clock. Currently the common clock
framework chooses a m250_div of 2 - with the internal fixed
"divide by 10" this results in a RGMII TX clock of 125001197Hz (120Hz
above the requested 125MHz).
Letting the common clock framework propagate the rate changes up to the
parent of m250_mux allows us to get the best possible clock rate. With
this patch the common clock framework calculates a rate of
very-close-to-250MHz (249999701Hz to be exact) for the MPLL2 clock
(which is the mux input). Dividing that by 2 (which is an internal,
fixed divider for the RGMII TX clock) gives us an RGMII TX clock of
124999850Hz (which is only 150Hz off the requested 125MHz, compared to
1197Hz based on the MPLL2 rate set by u-boot and the Amlogic GPL kernel
sources).
SoCs from the Meson GX series are not affected by this change because
the input clock is FCLK_DIV2 whose rate cannot be changed (which is fine
since it's running at 1GHz, so it's already a multiple of 250MHz and
125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to (but not exactly) 500MHz. The
exact rate is 500002394Hz, which is calculated in
drivers/clk/meson/clk-mpll.c using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5
The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 125MHz RGMII TX clock (on Gbit speeds,
the IP block internally divides that down to 25MHz on 100Mbit/s
connections and 2.5MHz on 10Mbit/s connections - we don't need any
special configuration for that).
Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate for the RGMII TX clock of
125001197Hz (= 125MHz plus 1197Hz), which is close-enough to 125MHz.
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tests (using an oscilloscope and an Odroid-C1 board with a RTL8211F
RGMII PHY) have shown that the PRG_ETH0 register behaves as follows:
- bit 4 is a mux to choose between two parent clocks. according to the
public S805 datasheet the only supported parent clock is MPLL2 (this
was not verified using the oscilloscope).
The public S805/S905 datasheet claims that this bit is reserved.
- bits 9:7 control a one-based divider (register value 1 means "divide
by 1", etc.) for the input clock. we call this clock the "m250_div"
clock because it's value is always supposed to be (close to) 250MHz
(see below for an explanation).
The description in the public S805/S905 datasheet is a bit cryptic,
but it comes down to "input clock = 250MHz * value" (which could also
be expressed as "250MHz = input clock / value")
- there seems to be an internal fixed divide-by-2 clock which takes the
output from the m250_div and divides it by 2. This is not unusual on
Amlogic SoCs, since the SDIO (MMC) driver also uses an internal fixed
divide-by-2 clock.
This is not documented in the public S805/S905 datasheet
- bit 10 controls a gate clock which enables or disables the RGMII TX
clock (which is an output on the MAC/SoC and an input in the PHY). we
call this the "rgmii_tx_en" clock. if this bit is set to "0" the RGMII
TX clock output is close to 0
The description for this bit in the public S805/S905 datasheet is
"Generate 25MHz clock for PHY". Based on these tests it's believed
that this is wrong, and should probably read "Generate the 125MHz
RGMII TX clock for the PHY"
- the RGMII TX clock has to be set to 125MHz - the IP block adjusts the
output (automatically) depending on the line speed (RGMII specifies
that Gbit connections use a 125MHz clock, 100Mbit/s connections use a
25MHz clock and 10Mbit/s connections use a 2.5MHz clock. only Gbit and
100Mbit/s were tested with an oscilloscope). Due to the requirement
that this clock always has to be set to 125MHz and due to the fixed
divide-by-2 parent clock this means that m250_div will always end up
with a rate of (close to) 250MHz.
- bits 6:5 are the TX delay, which is also named "clock phase" in some
of Amlogic's older GPL kernel sources.
The PHY also has an XTAL_IN pin where a 25MHz clock has to be provided.
Tests with the oscilloscope have shown that this is routed to a crystal
right next to the RTL8211F PHY. The same seems to be true on the Khadas
VIM2 (which uses a GXM SoC) board - however the 25MHz crystal is on the
other side of the PCB there.
This updates the clocks in the dwmac-meson8b driver by replacing the
"m25_div" with the "rgmii_tx_en" clock and additionally introducing a
fixed divide-by-2 clock between "m250_div" and "rgmii_tx_en".
Now we also need to set a frequency of 125MHz on the RGMII clock
(opposed to the 25MHz we set before, with that non-existing
divide-by-5-or-10 divider).
Special thanks go to Linus Lüssing for testing the various bits and
checking the results with an oscilloscope on his Odroid-C1!
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.
While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0dfb33a0d7e2 ("sch_red: report backlog information") copied
child's backlog into RED's backlog. Back then RED did not maintain
its own backlog counts. This has changed after commit 2ccccf5fb43f
("net_sched: update hierarchical backlog too") and commit d7f4f332f082
("sch_red: update backlog as well"). Copying is no longer necessary.
Tested:
$ tc -s qdisc show dev veth0
qdisc red 1: root refcnt 2 limit 400000b min 30000b max 30000b ecn
Sent 20942 bytes 221 pkt (dropped 0, overlimits 0 requeues 0)
backlog 1260b 14p requeues 14
marked 0 early 0 pdrop 0 other 0
qdisc tbf 2: parent 1: rate 1Kbit burst 15000b lat 3585.0s
Sent 20942 bytes 221 pkt (dropped 0, overlimits 138 requeues 0)
backlog 1260b 14p requeues 14
Recently RED offload was added. We need to make sure drivers don't
depend on resetting the stats. This means backlog should be treated
like any other statistic:
total_stat = new_hw_stat - prev_hw_stat;
Adjust mlxsw.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Nogah Frankel <nogahf@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The latest merge between net and net-next introduced a complier assert in
mlx5 driver. In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.
Fixes: c02b3741eb99 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping changes all over.
The mini-qdisc bits were a little bit tricky, however.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-01-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add initial BPF map offloading for nfp driver. Currently only
programs were supported so far w/o being able to access maps.
Offloaded programs are right now only allowed to perform map
lookups, and control path is responsible for populating the
maps. BPF core infrastructure along with nfp implementation is
provided, from Jakub.
2) Various follow-ups to Josef's BPF error injections. More
specifically that includes: properly check whether the error
injectable event is on function entry or not, remove the percpu
bpf_kprobe_override and rather compare instruction pointer
with original one, separate error-injection from kprobes since
it's not limited to it, add injectable error types in order to
specify what is the expected type of failure, and last but not
least also support the kernel's fault injection framework, all
from Masami.
3) Various misc improvements and cleanups to the libbpf Makefile.
That is, fix permissions when installing BPF header files, remove
unused variables and functions, and also install the libbpf.h
header, from Jesper.
4) When offloading to nfp JIT and the BPF insn is unsupported in the
JIT, then reject right at verification time. Also fix libbpf with
regards to ELF section name matching by properly treating the
program type as prefix. Both from Quentin.
5) Add -DPACKAGE to bpftool when including bfd.h for the disassembler.
This is needed, for example, when building libfd from source as
bpftool doesn't supply a config.h for bfd.h. Fix from Jiong.
6) xdp_convert_ctx_access() is simplified since it doesn't need to
set target size during verification, from Jesper.
7) Let bpftool properly recognize BPF_PROG_TYPE_CGROUP_DEVICE
program types, from Roman.
8) Various functions in BPF cpumap were not declared static, from Wei.
9) Fix a double semicolon in BPF samples, from Luis.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull rdma fixes from Doug Ledford:
"We had a few more items creep up over the last week. Given we are in
-rc8, these are obviously limited to bugs that have a big downside and
for which we are certain of the fix.
The first is a straight up oops bug that all you have to do is read
the code to see it's a guaranteed 100% oops bug.
The second is a use-after-free issue. We get away lucky if the queue
we are shutting down is empty, but if it isn't, we can end up oopsing.
We really need to drain the queue before destroying it.
The final one is an issue with bad user input causing us to access our
port array out of bounds. While fixing the array out of bounds issue,
it was noticed that the original code did the same thing twice (the
call to rdma_ah_set_port_num()), so its removal is not balanced by a
readd elsewhere, it was already where it needed to be in addition to
where it didn't need to be.
Summary:
- Oops fix in hfi1 driver
- use-after-free issue in iser-target
- use of user supplied array index without proper checking"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix out-of-bound access while querying AH
IB/hfi1: Prevent a NULL dereference
iser-target: Fix possible use-after-free in connection establishment error
|
|
Jesper Dangaard Brouer says:
====================
This patchset contains some small improvements and cleanup for
the Makefile in tools/lib/bpf/.
It worries me that the libbpf.so shared library is not versioned,
but it not addressed in this patchset.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The third parameter to do_install was not used by $(INSTALL) command.
Fix this by only setting the -m option when the third parameter is supplied.
The use of a third parameter was introduced in commit eb54e522a000 ("bpf:
install libbpf headers on 'make install'").
Without this change, the header files are install as executables files (755).
Fixes: eb54e522a000 ("bpf: install libbpf headers on 'make install'")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The plugin_dir_SQ variable is not used, remove it.
The function update_dir is also unused, remove it.
The variable $VERSION_FILES is empty, remove it.
These all originates from the introduction of the Makefile, and is likely a copy paste
from tools/lib/traceevent/Makefile.
Fixes: 1b76c13e4b36 ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
It seems like an oversight not to install the header file for libbpf,
given the libbpf.so + libbpf.a files are installed.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Jakub Kicinski says:
====================
This series combines a number of random improvements ranging from
libbpf to nfp driver. NFP patches make better use of the verifier
log. There is a requested adjustment to the map offload code, and
a warning fix for a W=1 build to the disassembler. Quentin also
fixes the libbpf program type detection, while Jiong allows the use
of libbfd compiled from source.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
If an eBPF instruction is unknown to the driver JIT compiler, we can
reject the program at verification time.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Use the verifier log to output error messages if map lookup
can't be offloaded.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
