| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley via Tony Lindgren:
Some OMAP hwmod fixes for v3.11-rc. Mostly intended to fix an earlyprintk
regression and an AM33xx cpgmac power management regression.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_a_v3.11-rc/20130730042132/
The tests include temporary fixes for the unrelated 2430SDP and OMAP3
boot regressions, which are not part of this signed tag.
* tag 'for-v3.11-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
ARM: OMAP2+: hwmod: rt address space index for DT
ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
ARM: OMAP2+: Avoid idling memory controllers with no drivers
ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fixes for omap5-uevm regulators from Nishanth Menon <nm@ti.com>:
Due to wrong older revision of documentation used as reference, we
seem to have a bunch of LDOs wrongly configured on OMAP5 uEVM. This
series is based power tree on production board 750-2628-XXX platform.
Unfortunately, the wrong voltages may be detrimental to OMAP5 as they
supply hardware blocks at voltages that are out of specification.
There is a chance that without these fixes there can be hardware
damage to omap5-uevm boards with the v3.11-rc series.
* tag 'omap-for-v3.11/fixes-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5-uevm: update optional/unused regulator configurations
ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
ARM: dts: omap5-uevm: document regulator signals used on the actual board
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes
From David Brown, fixes for MSM for 3.11:
Two small fixes for MSM.
The first fixes the a gpio controller register address. I didn't see
any acks from the devicetree maintainers, so I've copied them on this
pull request. The change itself is minor, and just to the register
address.
The second change removes the gpiomux V1 code from MSM. This was
breaking compilation for some of the targets.
* tag 'msm-3.11-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Consolidate gpiomux for older architectures
ARM: msm: dts: Fix the gpio register address for msm8960
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Register target address to be used for cpgmac is the second device
address space. By default, hwmod picks first address space (0th index)
for register target.
With removal of address space from hwmod and using DT instead, cpgmac
is getting wrong address space for register target.
Fix it by indicating the address space to be used for register target.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Address space is being removed from hwmod database and DT information
in <reg> property is being used. Currently the 0th index of device
address space is used to map for register target address. This is not
always true, eg. cpgmac has it's sysconfig in second address space.
Handle it by specifying index of device address space to be used for
register target. As default value of this field would be zero with
static initialization, existing behaviour of using first address space
for register target while using DT would be kept as such.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
[paul@pwsan.com: use u8 rather than int to save memory]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Some hwmods which are marked with HWMOD_INIT_NO_IDLE are left in enabled
state post setup(). When a omap_device gets created for such hwmods
make sure the omap_device and pm_runtime states are also in sync for such
hwmods by doing a omap_device_enable() and pm_runtime_set_active() for the
device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Memory controllers in OMAP (like GPMC and EMIF) have the hwmods marked with
HWMOD_INIT_NO_IDLE and are left in enabled state post initial setup.
Even if they have drivers missing, avoid idling them as part of
omap_device_late_idle()
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
With commit '82702ea11ddfe0e43382e1fa5b66d807d8114916' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.
This was rootcaused to hwmod trying to reset console uart while
earlycon was using it. The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.
Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.
This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Mark Jackson <mpfj-list@newflow.co.uk>
Reported-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.
The following optional/unused regulators can be updated:
- SMPS9 supplies TWL6040 over VDDA_2v1_AUD. This regulator needs to be
enabled only when audio is active. Since it does not come active by
default, it does not require "always-on" or "boot-on".
- LDO2 and LDO8 do not go to any peripheral or connector on the board.
Further, these unused regulators should have been 2.8V for LDO2 and
3.0V for LDO8. Mark these LDOs as disabled in the dts until needed.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.
The following fixes are hence mandatory to ensure right voltage is
supplied to key OMAP5 SoC voltage rails:
- LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This
can only be supplied at 1.5V or 1.8V and we currently supply 2.8V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is
a 'on need' supply to SoC IP and is not enabled by PMIC by
default at boot.
- LDO3 supplies Low Latency Interface(LLI) hardware module which is a
special hardware to communicate with Modem. However since uEVM is
not setup by default for this communication, this should be disabled
by default.
Further, vdda_lli is supposed to be 1.5V and not 3V.
- LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi
This can only be supplied at 1.5V or 1.8V and we currently
supply 2.2V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is a 'on need'
supply to SoC IP and is not enabled by PMIC by default at boot.
- LDO6 supplies the board specified VDDS_1V2_WKUP supply going to
ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply
1.2V instead of 1.5V.
- LDO7 supplies VDD_VPP which is vpp1. This is currently configured for
1.5V which as per data manual "A pulse width of 1000 ns and an amplitude
of 2V is required to program each eFuse bit. Otherwise, VPP1 must not
be supplied".
So, fix the voltage to 2V. and disable the supply since we have no plans
of programming efuse bits - it can only be done once - in factory.
Further it is not enabled by default by PMIC so, 'boot-on' must be
removed, and the 'always-on' needs to be removed to achieve pulsing
if efuse needs to be programmed.
- LDO9 supplies the board specified vdds_sdcard supply going within SoC
specification of 1.8V or 3.0V. Further the supply is controlled by
switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to
be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled
on need basis.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, currently we use the Palmas regulator names which is used for
different purposes on uEVM. Document the same based on 750-2628-XXX
boards - which is meant to be supported by this dts.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg is working on fixing a very tight race between opening a event
file and deleting that event at the same time (both must be done as
root).
I also found a bug while testing Oleg's patches which has to do with a
race with kprobes using the function tracer.
There's also a deadlock fix that was introduced with the previous
fixes"
* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
ftrace: Add check for NULL regs if ops has SAVE_REGS set
tracing: Kill trace_cpu struct/members
tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is five bug fixes, two of which fix long standing problems
causing crashes (sd and mvsas). The remaining three are hung (isci
race) or lost (qla2xxx, isci) devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] isci: fix breakage caused by >16byte CDB patch
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
[SCSI] sd: fix crash when UA received on DIF enabled device
[SCSI] qla2xxx: Properly set the tagging for commands.
[SCSI] isci: Fix a race condition in the SSP task management path
|
|
Msm gpiomux can be used only for 7x30 and 8x50.
Prevent compilation and fix build issues on 7X00, 8X60 and 8960.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
Pull drm fixes from Dave Airlie:
"This is just a regular fixes pull apart from the qxl one, it has
radeon and intel bits in it,
The intel fixes are for a regression with the RC6 fix and a 3.10 hdmi
regression, whereas radeon is more DPM fixes, a few lockup fixes and
some rn50/r100 DAC fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
|
|
Pull qxl drm fixes from Dave Airlie:
"Okay as I warned, the qxl driver was running a bit free and loose with
its ttm object reservations and the new lockdep enabled reservation
tracking shone a bright light into it, it also with the new
reservations mutexes hits a possible deadlock during boot.
The first patch is a real fix to render the console correctly as the
driver used to just drop irq renderering as too hard, this also fixes
a sleeping while atomic warning.
The other two patches are the big ugly ones that redo how the driver
allocates objects and reserves them and makes things all work
properly, I've tested this in a VM, and compared to the current code
which hits a lockdep warning and the sleep while atomic warning before
failing.
So sorry this is coming in late, I should have tested qxl before
merging the mutex code, but I'd rather just fix qxl with this than
revert the reservations code at this point"
* 'qxl-fixes' of git://people.freedesktop.org/~airlied/linux:
qxl: convert qxl driver to proper use for reservations
qxl: allow creation of pre-pinned objects and use for releases.
drm/qxl: add delayed fb operations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are just two fixes, a revert of the would-be backlight fix that
didn't work and an intel_pstate fix for two problems related to
maximum P-state selection.
Specifics:
- Revert of the ACPI video commit that I hoped would help fix
backlight problems related to Windows 8 compatibility on some
systems. Unfortunately, it turned out to cause problems to happen
too.
- Fix for two problems in intel_pstate, a possible failure to respond
to a load change on a quiet system and a possible failure to select
the highest available P-state on some systems. From Dirk
Brandewie"
* tag 'pm+acpi-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video / i915: No ACPI backlight if firmware expects Windows 8"
cpufreq / intel_pstate: Change to scale off of max P-state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- Stack size increased to 16K (similar to other 64-bit architectures)
- Additional cache flushing for secondary CPUs boot mode
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Change kernel stack size to 16K
arm64: Fix definition of arm_pm_restart to match the declaration
arm64: virt: ensure visibility of __boot_cpu_mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a largeish batch of fixes, mostly because I missed -rc2 due to
travel/vacation. So in number these are a bit more than ideal unless
you amortize them over two -rcs.
Quick breakdown:
- Defconfig updates
- Making multi_v7_defconfig useful on more hardware to encourage
single-image usage
- Davinci and nomadik updates due to new code merged this merge
window
- Fixes for UART on Samsung platforms, both PM and clock-related
- A handful of warning fixes from defconfig builds, including for
max8925 backlight and pxamci (both with appropriate acks)
- Exynos5440 fixes for LPAE configuration, PM
- ...plus a bunch of other smaller changes all over the place
I expect to switch to regressions-or-severe-bugs-only fixes from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
mfd: max8925: fix dt code for backlight
ARM: omap5: Only select errata 798181 if SMP
ARM: EXYNOS: Update CONFIG_ARCH_NR_GPIO for Exynos
ARM: EXYNOS: Fix low level debug support
ARM: SAMSUNG: Save/restore only selected uart's registers
ARM: SAMSUNG: Add SAMSUNG_PM config option to select pm
ARM: S3C24XX: Add missing clkdev entries for s3c2440 UART
ARM: multi_v7_defconfig: Select USB chipidea driver
ARM: pxa: propagate errors from regulator_enable() to pxamci
ARM: zynq: fix compilation warning
ARM: keystone: fix compilation warning
ARM: highbank: Only touch common coherency control register fields
ARM: footbridge: fix overlapping PCI mappings
dmaengine: shdma: fix a build failure on platforms with no DMA support
ARM: STi: Set correct ARM ERRATAs.
ARM: dts: STi: Fix pinconf setup for STiH416 serial2
ARM: nomadik: configure for NO_HZ and HRTIMERS
ARM: nomadik: update defconfig base
ARM: nomadik: Update MMC defconfigs
ARM: davinci: defconfig: enable EDMA driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.11-rc3.
Lots of little things, nothing major. A number of new device ids,
build fixes for DMA, and a bunch of other minor things. All of these
have been in the linux-next tree"
* tag 'usb-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: Clear both buffers when clearing a control transfer TT buffer.
usb/gadget: free opts struct on error recovery
USB: mos7840: fix memory leak in open
usb: serial: option.c: remove ONDA MT825UP product ID fromdriver
usb: serial: option: add Olivetti Olicard 200
usb: serial: option: blacklist ONDA MT689DC QMI interface
xhci: fix null pointer dereference on ring_doorbell_for_active_rings
usb: host: xhci: Enable XHCI_SPURIOUS_SUCCESS for all controllers with xhci 1.0
usb: fix build warning in pci-quirks.h when CONFIG_PCI is not enabled
usb: xhci: Mark two functions __maybe_unused
xhci: Avoid NULL pointer deref when host dies.
usb: serial: option: Add ONYX 3G device support
USB: ti_usb_3410_5052: fix dynamic-id matching
usb: option: add TP-LINK MA260
USB: option: add D-Link DWM-152/C1 and DWM-156/C1
USB: EHCI: Fix resume signalling on remote wakeup
USB: cp210x: add MMB and PI ZigBee USB Device Support
usb: cp210x support SEL C662 Vendor/Device
USB: option: append Petatel NP10T device to GSM modems list
USB: misc: Add Manhattan Hi-Speed USB DVI Converter to sisusbvga
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are 3 fixes for TTY and serial issues that have been reported.
Nothing huge, but nice to get fixed"
* tag 'tty-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: tegra: correct help message in Kconfig from 'ttyHS' to 'ttyTHS'
tty/8250_early: Don't truncate last character of options
TTY: snyclinkmp: calculating wrong addresses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some tiny drivers/staging/ fixes for 3.11-rc3
A number of bugfixes, all pretty tiny, but resolve issues that have
been reported (the kstrtos32 change fixes a data corruption problem
that Dan found). And a MAINTAINERS file update for the comedi
drivers"
* tag 'staging-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: Update the list of maintainers for staging/comedi driver.
staging: tidspbridge: replace strict_strtol() with kstrtos32()
staging: android: logger: Correct write offset reset on error
staging: zram: protect zram_reset_device() call
staging: gdm72xx: potential use after free in send_qos_list()
staging: drm/imx: drop "select OF_VIDEOMODE"
staging: frontier: use after free in disconnect()
staging: comedi: fix a race between do_cmd_ioctl() and read/write
staging: comedi: COMEDI_CANCEL ioctl should wake up read/write
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here are some char/misc patches for 3.11-rc3. It's pretty much just:
- mei fixes
- hyperv fixes
- new ja_JP translation update
all tiny stuff, but fixes for issues people have reported."
* tag 'char-misc-3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
HOWTO ja_JP sync
mei: me: fix waiting for hw ready
mei: don't have to clean the state on power up
mei: me: fix reset state machine
mei: hbm: fix typo in error message
Tools: hv: KVP: Fix a bug in IPV6 subnet enumeration
Drivers: hv: balloon: Do not post pressure status if interrupted
Drivers: hv: balloon: Fix a bug in the hot-add code
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a handful of regression and small fixes in ASoC, HD-audio and
USB-audio drivers.
- Sigmetal HD-audio codec regression fixes
- A copule of XRUN indication fixes for usb-audio devices
- ASoC: ep93xx build fix, sgtl5000 fix for probe order changes,
max98088 register access fix, etc"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hiface: return correct XRUN indication
ASoC: tegra: correct playback_dma_data setup
ASoC: core: double free in snd_soc_add_platform()
ALSA: usb-audio: 6fire: return correct XRUN indication
ASoC: ep93xx: fix build of ep93xx-ac97.c
ALSA: hda - Remove NO_PRESENCE bit override for Dell 1420n Laptop
ALSA: hda - Fix EAPD GPIO control for Sigmatel codecs
ASoC: atmel-ssc: remove clk_disable_unprepare call from critical section
ASoC: sgtl5000: defer the probe if clock is not found
ASoC: max98088 - fix element type of the register cache.
|
|
Pull xfs fix from Ben Myers:
"Fix for regression in commit cca9f93a52d2 ("xfs: don't do IO when
creating an new inode"), recovery causing filesystem corruption after
a crash"
* tag 'for-linus-v3.11-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: di_flushiter considered harmful
|
|
Pull nfsd fix from Bruce Fields:
"One more nfsd bugfix for 3.11"
* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
nfsd: nfsd_open: when dentry_open returns an error do not propagate as struct file
|
|
Pull md fixes from Neil Brown:
"Two more bugfixes for md in 3.11
Both marked for -stable, both since 3.3. I guess I should spend more
time testing..."
* tag 'md/3.11-fixes' of git://neil.brown.name/md:
md/raid5: fix interaction of 'replace' and 'recovery'.
md/raid10: remove use-after-free bug.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Assorted libata updates.
The most critical one is a fix for ahci oops during boot. Also, a new
smallish platform ahci driver is added and sata_inic162x is marked
clearly as experimental (it whines during boot too) as data corruption
seems rather common on the device and it's unlikely to get any love in
the foreseeable future. If the whining doesn't draw any attention, I
think we'd probably be better of making the driver depend on BROKEN in
a couple releases"
This is v2 of this pull request with fixed dependencies for ahci_imx.
* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_imx: depend on CONFIG_MFD_SYSCON
ahci_imx: add ahci sata support on imx platforms
ARM: imx6q: update the sata bits definitions of gpr13
ahci: fix Null pointer dereference in achi_host_active()
libata: make it clear that sata_inic162x is experimental
libata: replace strict_strtol() with kstrtol()
ata: Fix DVD not dectected at some platform with Wellsburg PCH
|
|
We attempted to address a regression introduced by commit a57f7f9
(ACPICA: Add Windows8/Server2012 string for _OSI method.) after which
ACPI video backlight support doesn't work on a number of systems,
because the relevant AML methods in the ACPI tables in their BIOSes
become useless after the BIOS has been told that the OS is compatible
with Windows 8. That problem is tracked by the bug entry at:
https://bugzilla.kernel.org/show_bug.cgi?id=51231
Commit 8c5bd7a (ACPI / video / i915: No ACPI backlight if firmware
expects Windows 8) introduced for this purpose essentially prevented
the ACPI backlight support from being used if the BIOS had been told
that the OS was compatible with Windows 8 and the i915 driver was
loaded, in which case the backlight would always be handled by i915.
Unfortunately, however, that turned out to cause problems with
backlight to appear on multiple systems with symptoms indicating that
i915 was unable to control the backlight on those systems as
expected.
For this reason, revert commit 8c5bd7a, but leave the function
acpi_video_backlight_quirks() introduced by it, because another
commit on top of it uses that function.
References: https://lkml.org/lkml/2013/7/21/119
References: https://lkml.org/lkml/2013/7/22/261
References: https://lkml.org/lkml/2013/7/23/429
References: https://lkml.org/lkml/2013/7/23/459
References: https://lkml.org/lkml/2013/7/23/81
References: https://lkml.org/lkml/2013/7/24/27
Reported-and-tested-by: James Hogan <james@albanarts.com>
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Reported-by: Kalle Valo <kvalo@adurom.com>
Tested-by: Joerg Platte <jplatte@naasa.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ahci_imx makes use of regmap but the dependency wasn't specified in
Kconfig leading build failures if CONFIG_AHCI_IMX is enabled but
CONFIG_MFD_SYSCON is not. Add the Kconfig dependency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
Commit a82274151af "tracing: Protect ftrace_trace_arrays list in trace_events.c"
added taking the trace_types_lock mutex in trace_events.c as there were
several locations that needed it for protection. Unfortunately, it also
encapsulated a call to tracing_reset_all_online_cpus() which also takes
the trace_types_lock, causing a deadlock.
This happens when a module has tracepoints and has been traced. When the
module is removed, the trace events module notifier will grab the
trace_types_lock, do a bunch of clean ups, and also clears the buffer
by calling tracing_reset_all_online_cpus. This doesn't happen often
which explains why it wasn't caught right away.
Commit a82274151af was marked for stable, which means this must be
sent to stable too.
Link: http://lkml.kernel.org/r/51EEC646.7070306@broadcom.com
Reported-by: Arend van Spril <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Cc: Alexander Z Lam <azl@google.com>
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Cc: David Sharp <dhsharp@google.com>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Written by Catalin Marinas, tested by APM on storm platform. This is needed
because of the failures encountered when running SpecWeb benchmark test.
Signed-off-by: Feng Kan <fkan@apm.com>
Acked-by: Kumar Sankaran <ksankaran@apm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Brown-paper-bag pull request here. The snb rc6 fix from the last pull
broke forcewake BIOS dirt cleanup, which with fixed. But that fix broke
the spinlock init sequence, which results in an ugly BUG when spinlock
debugging is enabled :( So I get to throw another patch at cc: stable to
fix up the mess ...
* tag 'drm-intel-fixes-2013-07-25' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: initialize gt_lock early with other spin locks
drm/i915: fix hdmi portclock limits
|
|
into drm-fixes
r600 dpm fixes, old school card dac fixes, lockup fixes
endian fixes
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix r600_enable_sclk_control()
drm/radeon/dpm: implement force performance levels for rv6xx
drm/radeon/dpm: fix displaygap programming on rv6xx
drm/radeon/dpm: fix a typo in the rv6xx mclk setup
drm/radeon: fix combios tables on older cards
drm/radeon: improve dac adjust heuristics for legacy pdac
drm/radeon: Another card with wrong primary dac adj
drm/radeon: fix endian issues with DP handling (v3)
drm/radeon/vm: only align the pt base to 32k
drm/radeon: wait for 3D idle before using CP DMA
|
|
Actually program the correct register to enable
engine clock scaling control.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Allows you to limit the selected power levels via sysfs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The device-tree enablement for max8925 has several problems, but besides
the bindings being wrong (and not having seen review) there's also some
bad coding practices on how to fill in the platform_data from device tree.
I came across this since it causes a warning when compiling
mmp2_defconfig, and instead of doing the minimal fix to silence the
warning, I restructured the code a bit.
This silences the warning:
drivers/video/backlight/max8925_bl.c: In function 'max8925_backlight_probe':
drivers/video/backlight/max8925_bl.c:177:3: warning: statement with no effect [-Wunused-value]
Note that the bindings themselves need to be revisited too, but that will
affect more than just the backlight driver and is best done separately;
this just fixes the bad code for the backlight driver.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Need to use the driver state rather than the register
state since the displays may not be enabled when the
power state is programmed.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Need to set high for the last two entries. Looks
like a copy and paste typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix memory leaks introduced in commits:
40d133d7f542616cf9538508a372306e626a16e9
usb: gadget: f_ncm: convert to new function interface with backward compatibility
fee562a6450b7806f1fbbe1469a67b5395b5c10a
usb: gadget: f_ecm: convert to new function interface with backward compatibility
fcbdf12ebef73a6069e2a1aada1e546fb578a4aa
usb: gadget: f_phonet: convert to new function interface with backward compatibility
b29002a157940752dfed2c488b2011f63f007d71
usb: gadget: f_eem: convert to new function interface with backward compatibility
8cedba7c73af1369599b1111639cfeb66fe13aaa
usb: gadget: f_subset: convert to new function interface with backward compatibility
f466c6353819326873fa48a02c6f2d7c903240d6
usb: gadget: f_rndis: convert to new function interface with backward compatibility
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allocated urbs and buffers were never freed on errors in open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Bug fixes, now with more tags!
Hi Greg,
Here's five bug fixes for 3.12.
The three patches are marked for stable. Two fix NULL pointer dereferences.
The third marked for stable suppresses some serious log spam from unnecessary
xHCI driver warnings, whenever an isochronous short packet happens on an xHCI
1.0 host.
The other two patches fix build warnings.
Sarah Sharp
|
|
When we made all inode updates transactional, we no longer needed
the log recovery detection for inodes being newer on disk than the
transaction being replayed - it was redundant as replay of the log
would always result in the latest version of the inode would be on
disk. It was redundant, but left in place because it wasn't
considered to be a problem.
However, with the new "don't read inodes on create" optimisation,
flushiter has come back to bite us. Essentially, the optimisation
made always initialises flushiter to zero in the create transaction,
and so if we then crash and run recovery and the inode already on
disk has a non-zero flushiter it will skip recovery of that inode.
As a result, log recovery does the wrong thing and we end up with a
corrupt filesystem.
Because we have to support old kernel to new kernel upgrades, we
can't just get rid of the flushiter support in log recovery as we
might be upgrading from a kernel that doesn't have fully transactional
inode updates. Unfortunately, for v4 superblocks there is no way to
guarantee that log recovery knows about this fact.
We cannot add a new inode format flag to say it's a "special inode
create" because it won't be understood by older kernels and so
recovery could do the wrong thing on downgrade. We cannot specially
detect the combination of zero mode/non-zero flushiter on disk to
non-zero mode, zero flushiter in the log item during recovery
because wrapping of the flushiter can result in false detection.
Hence that makes this "don't use flushiter" optimisation limited to
a disk format that guarantees that we don't need it. And that means
the only fix here is to limit the "no read IO on create"
optimisation to version 5 superblocks....
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit e60896d8f2b81412421953e14d3feb14177edb56)
|
|
We forgot to free the node itself when free:ing a map.
Reported-by: xulinuxkernel <xulinuxkernel@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
