| Age | Commit message (Collapse) | Author |
|---|
|
While migrating the bcm_sf2 driver to use b53_common, we left a small
piece untouched where we kept our local copy of the per-port
port_vlan_ctl bitmask value. This value is now maintained by b53_device
so we need to use it instead of our local (and now stale) copy of it.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Ahern says:
====================
net: Convert vrf to tx hook
The motivation for this series is that ICMP Unreachable - Fragmentation
Needed packets are not handled properly for VRFs. Specifically, the
FIB lookup in __ip_rt_update_pmtu fails so no nexthop exception is
created with the reduced MTU. As a result connections stall if packets
larger than the smallest MTU in the path are generated.
While investigating that problem I also noticed that the MSS for all
connections in a VRF is based on the VRF device's MTU and not the
route the packets ultimately go through. VRF currently uses a dst
to direct packets to the device. The first FIB lookup returns this dst
and then the lookup in the VRF driver gets the actual output route. A
side effect of this design is that the VRF dst is cached on sockets
and then used for calculations like the MSS.
This series fixes this problem by removing the hook in the FIB lookups
that returns the dst pointing to the VRF device to the VRF and always
doing the actual FIB lookup. This allows the real dst to be used
throughout the stack (for example the MSS). Packets are diverted to
the VRF device on Tx using an l3mdev hook in the output path similar to
to what is done for Rx. The end result is a simpler implementation for
VRF with fewer intrusions into the network stack and symmetrical packet
handling for Rx and Tx paths.
Comparison of netperf performance for a build without l3mdev (best case
performance), the old vrf driver and the VRF driver from this series.
Data are collected using VMs with virtio + vhost. The netperf client
runs in the VM and netserver runs in the host. 1-byte RR tests are done
as these packets exaggerate the performance hit due to the extra lookups
done for l3mdev and VRF.
Command: netperf -cC -H ${ip} -l 60 -t {TCP,UDP}_RR [-J red]
TCP_RR UDP_RR
IPv4 IPv6 IPv4 IPv6
no l3mdev 29,996 30,601 31,638 24,336
vrf old 27,417 27,626 29,159 24,801
vrf new 28,036 28,372 30,110 24,857
l3mdev, no vrf 29,534 30,465 30,670 24,346
* Transactions per second as reported by netperf
* netperf modified to take a bind-to-device argument -- the -J red option
1. 'no l3mdev' == NET_L3_MASTER_DEV is unset so code is compiled out
2. 'vrf old' == data for existing implementation
3. 'vrf new' == data with this series
4. 'l3mdev, no vrf' == NET_L3_MASTER_DEV is enabled but traffic is not
going through a VRF
About the series
- patch 1 adds the flow update (changing oif or iif to L3 master device
and setting the flag to skip the oif check) to ipv4 and ipv6 paths just
before hitting the rules. This catches all code paths in a single spot.
- patch 2 adds the Tx hook to push the packet to the l3mdev if relevant
- patch 3 adds some checks so the vrf device can act as a vrf-local
loopback. These changes were not needed before since the vrf dst was
returned from the lookup.
- patches 4 and 5 flip the ipv4 and ipv6 stacks to the tx hook leaving
the route lookup to be the real one. The dst flip happens at the
beginning of the L3 output path so the VRFs can have device based
features such as netfilter, tc and tcpdump.
- patches 6-11 remove no longer needed l3mdev code
v2
- properly handle IPv6 link scope addresses
- keep the device xmit path and associated dst which is switched in by
the l3_out hook. packets still need to go through the xmit path in
case the user puts a qdisc on the vrf device and to allow tc rules.
version 1 short circuited the tx handling and only covered netfilter
and tcpdump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer used
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer used
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer used
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer needed
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer needed
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A previous patch added l3mdev flow update making these hooks
redundant. Remove them.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flip the IPv6 output path to use the l3mdev tx out hook. The VRF dst
is not returned on the first FIB lookup. Instead, the dst on the
skb is switched at the beginning of the IPv6 output processing to
send the packet to the VRF driver on xmit.
Link scope addresses (linklocal and multicast) need special handling:
specifically the oif the flow struct can not be changed because we
want the lookup tied to the enslaved interface. ie., the source address
and the returned route MUST point to the interface scope passed in.
Convert the existing vrf_get_rt6_dst to handle only link scope addresses.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flip the IPv4 output path to use the l3mdev tx out hook. The VRF dst
is not returned on the first FIB lookup. Instead, the dst on the
skb is switched at the beginning of the IPv4 output processing to
send the packet to the VRF driver on xmit.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow an L3 master device to act as the loopback for that L3 domain.
For IPv4 the device can also have the address 127.0.0.1.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the infrastructure to the output path to pass an skb
to an l3mdev device if it has a hook registered. This is the Tx parallel
to l3mdev_ip{6}_rcv in the receive path and is the basis for removing
the existing hook that returns the vrf dst on the fib lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add l3mdev hook to set FLOWI_FLAG_SKIP_NH_OIF flag and update oif/iif
in flow struct if its oif or iif points to a device enslaved to an L3
Master device. Only 1 needs to be converted to match the l3mdev FIB
rule. This moves the flow adjustment for l3mdev to a single point
catching all lookups. It is redundant for existing hooks (those are
removed in later patches) but is needed for missed lookups such as
PMTU updates.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the indentation for a call of the macro "DPRINTK" in this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* The script "checkpatch.pl" can point information out like the following.
WARNING: Prefer kcalloc over kzalloc with multiply
Thus fix the affected source code place.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
* Delete the local variable "size" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The script "checkpatch.pl" can point out that assignments should usually
not be performed within condition checks.
Thus move an assignment for a local variable to a separate statement
in this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* The script "checkpatch.pl" can point out that assignments should usually
not be performed within condition checks.
Thus move an assignment for a local variable to a separate statement
in this function.
* Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the specification of a data structure by a reference for a field
in a local variable as the parameter for the operator "sizeof" to make
the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Willem noticed that we could avoid an rbtree lookup if the
the attempt to coalesce incoming skb to the last skb failed
for some reason.
Since most ooo additions are at the tail, this is definitely
worth adding a test and fast path.
Suggested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When userspace tries to create datapaths and the module is not loaded,
it will simply fail. With this patch, the module will be automatically
loaded.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions are used by other code misc-next tree.
This reverts commit 30d1de08c87ddde6f73936c3350e7e153988fe02.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
Mellanox 100G mlx5 seamless error recovery
This series from Mohamad improves the driver load/unload flows
to seamlessly handle pci errors and device internal errors recovery
reset flows.
Current pci and internal error handling is too heavy and is done
with a full restart of the driver by unregistering mlx5 interfaces
(mlx5e netedevs and mlx5_ib) which will cause losing all the current
interfaces and mlx5 core configurations.
To improve this, we add new callback functions of mlx5 interface
object (attach/detach) to be called upon reset flows when errors are
detected rather than calling register and unregister interfaces.
On their side, interfaces such as (mlx5e and mlx5_ib) can choose to implement
those callback, if not, the old heavy reset will be called for that interface.
For non-interface mlx5 modules such as sriov and eswitch, we refactored
and reorganized the code in a way that the software state objects are created
only once on driver load. Those software state objects are kept upon reset recovery
flows and only freed once on driver unload. On seamless soft reset flows, only
hardware resources are released on stop and re-allocated on start according to the
current soft state.
In this series only mlx5e interface implements attach/detach callbacks
so that the netdevice will be kept alive on reset. On detach only hardware resources
are released and the netdevice will be marked as detached to the stack. Once
attached again it will re-allocate the hardware resources according to the current
netdevice state, and all the configurations and the software state will be kept or restored
after recovery.
Note: I will be out of office all next week, in case of any updates
or V2 is required, Tariq will post the new series, I hope it is ok.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hide the exposed (external) mlx5_dev_list and mlx5_intf_mutex and expose
an organized modular API to manage and manipulate mlx5 devices list.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When detaching the mlx5e interface clear all the vlans rules from the
vlan flow table.
When attaching it back restore all the active vlans rules to the HW.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Needed to support seamless and lightweight PCI/Internal error recovery.
Implement the attach/detach interface callbacks.
In attach callback we only allocate HW resources.
In detach callback we only deallocate HW resources.
All SW/kernel objects initialzing/destroying is kept in add/remove
callbacks.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Save the user configuration in the vport sturct.
Restore saved old configuration upon vport enable.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Init/cleanup sriov/eswitch in the core software context init/cleanup
flows.
Attach/detach sriov/eswitch in the core load/unload flows.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Needed for lightweight and modular internal/pci error handling.
Implement eswitch attach function which allocates/starts hw related
resources.
Implement eswitch detach function which releases/stops hw related
resources.
Init/cleanup function only handle eswitch software context allocation
and destruction.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Needed for lightweight and modular internal/pci error handling.
Implement sriov attach function which enables pre-saved number of vfs on
the device side.
Implement sriov detach function which disable the current vfs on the
device side.
Init/cleanup function only handles sriov software context allocation and
destruction.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gather all software context creating/destroying in one function and call
it once in the first load and in the last unload.
load/unload functions will now receive indication if we need to
create/destroy the software contexts.
In internal/pci error do the unload/load flows without releasing the
software objects.
In this way we perserve the sw core state and it help us restoring old
driver state after PCI error/shutdown.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add attach/detach callbacks to interface API.
This is crucial for implementing seamless reset flow which releases the
hardware and it's resources upon detach while keeping software
structures and state (e.g netdev) then reset and reallocate the hardware
needed resources upon attach.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the code and makes it look modular and symmetric.
Split sriov enable/disable to two levels: device level and pci level.
When user enable/disable sriov (via sriov_configure driver callback) we
will enable/disable both device and pci sriov.
When driver load/unload we will enable/disable (on demand) only device
sriov while keeping the PCI sriov enabled for next driver load.
On internal/pci error, VFs will be kept enabled on PCI and the reset
is done only in device level.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of device in internal error state there is no need to wait for
vf pages since they will be reclaimed manually later in the unload flow.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Javier Martinez Canillas says:
====================
net: use IS_ENABLED() instead of checking for built-in or module
This trivial series replace the open coding to check for a Kconfig symbol
being built-in or module, with IS_ENABLED() macro that does exactly that.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christophe Leroy says:
====================
Optimisation of fs_enet ethernet driver
This set optimises the freescale fs_enet ethernet driver:
1/ Merge of RX and TX NAPI functions in order to limit the amount of
interrupts
2/ Do not unmap DMA when packets len is below copybreak, otherwise there
is no benefit in copying the skb instead of allocating a new one
3/ Make copybreak value configurable as the optimised value is not the
same on all targets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Measurement shows that on a MPC8xx running at 132MHz, the optimal
limit is 112:
* 114 bytes packets are processed in 147 TB ticks with higher copybreak
* 114 bytes packets are processed in 148 TB ticks with lower copybreak
* 128 bytes packets are processed in 154 TB ticks with higher copybreak
* 128 bytes packets are processed in 148 TB ticks with lower copybreak
* 238 bytes packets are processed in 172 TB ticks with higher copybreak
* 238 bytes packets are processed in 148 TB ticks with lower copybreak
However it might be different on other processors
and/or frequencies. So it is useful to make it configurable.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the length of the packet is below the defined copybreak limit,
the received packet is copied into a newly allocated skb in order
to reuse the skb. This is only interesting if it allow us to avoid
a new DMA mapping. We shall therefore not DMA unmap and remap the
skb->data. Instead, we invalidate the cache
with dma_sync_single_for_cpu() once the received data has been
copied into the new skb.
The following measures have been obtained on a mpc885 running at 132Mhz.
Measurement is done using the timebase with packets sent to the target
with 'ping -s 1' (packet len is 60):
* Without this patch: 182 TB ticks
* With this patch: 143 TB ticks
As a comparison, if we set the copybreak limit to 0, then we get
148 TB ticks. It means that without this patch, duration is even
worse when copying received data to a new skb instead of
allocating a new skb for next packet to be received
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initially, a NAPI TX routine has been implemented separately from
NAPI RX, as done on the freescale/gianfar driver.
By merging NAPI RX and NAPI TX, we reduce the amount of TX completion
interrupts.
Handling of the budget in association with TX interrupts is based on
indications provided at https://wiki.linuxfoundation.org/networking/napi
We never proceed more than the complete TX ring on a single run.
At the same time, we fix an issue in the handling of fep->tx_free:
It is only when fep->tx_free goes up to MAX_SKB_FRAGS that
we need to wake up the queue. There is no need to call
netif_wake_queue() at every packet successfully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
