summaryrefslogtreecommitdiff
path: root/include/linux/pinctrl/pinconf-generic.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/linux/pinctrl/pinconf-generic.h')
-rw-r--r--include/linux/pinctrl/pinconf-generic.h64
1 files changed, 32 insertions, 32 deletions
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index fe65962b264f..d921afd5f109 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -20,6 +20,11 @@
/**
* enum pin_config_param - possible pin configuration parameters
+ * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it
+ * weakly drives the last value on a tristate bus, also known as a "bus
+ * holder", "bus keeper" or "repeater". This allows another device on the
+ * bus to change the value by driving the bus high or low and switching to
+ * tristate. The argument is ignored.
* @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a
* transition from say pull-up to pull-down implies that you disable
* pull-up in the process, this setting disables all biasing.
@@ -29,14 +34,6 @@
* if for example some other pin is going to drive the signal connected
* to it for a while. Pins used for input are usually always high
* impedance.
- * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it
- * weakly drives the last value on a tristate bus, also known as a "bus
- * holder", "bus keeper" or "repeater". This allows another device on the
- * bus to change the value by driving the bus high or low and switching to
- * tristate. The argument is ignored.
- * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
- * impedance to VDD). If the argument is != 0 pull-up is enabled,
- * if it is 0, pull-up is total, i.e. the pin is connected to VDD.
* @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
* impedance to GROUND). If the argument is != 0 pull-down is enabled,
* if it is 0, pull-down is total, i.e. the pin is connected to GROUND.
@@ -48,10 +45,9 @@
* If the argument is != 0 pull up/down is enabled, if it is 0, the
* configuration is ignored. The proper way to disable it is to use
* @PIN_CONFIG_BIAS_DISABLE.
- * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
- * low, this is the most typical case and is typically achieved with two
- * active transistors on the output. Setting this config will enable
- * push-pull mode, the argument is ignored.
+ * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
+ * impedance to VDD). If the argument is != 0 pull-up is enabled,
+ * if it is 0, pull-up is total, i.e. the pin is connected to VDD.
* @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
* collector) which means it is usually wired with other output ports
* which are then pulled up with an external resistor. Setting this
@@ -59,28 +55,26 @@
* @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source
* (open emitter). Setting this config will enable open source mode, the
* argument is ignored.
+ * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
+ * low, this is the most typical case and is typically achieved with two
+ * active transistors on the output. Setting this config will enable
+ * push-pull mode, the argument is ignored.
* @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current
* passed as argument. The argument is in mA.
+ * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
+ * which means it will wait for signals to settle when reading inputs. The
+ * argument gives the debounce time in usecs. Setting the
+ * argument to zero turns debouncing off.
* @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not
* affect the pin's ability to drive output. 1 enables input, 0 disables
* input.
- * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
- * If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
- * schmitt-trigger mode is disabled.
* @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in
* schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis,
* the threshold value is given on a custom format as argument when
* setting pins to this mode.
- * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
- * which means it will wait for signals to settle when reading inputs. The
- * argument gives the debounce time in usecs. Setting the
- * argument to zero turns debouncing off.
- * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
- * supplies, the argument to this parameter (on a custom format) tells
- * the driver which alternative power source to use.
- * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
- * this parameter (on a custom format) tells the driver which alternative
- * slew rate to use.
+ * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
+ * If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
+ * schmitt-trigger mode is disabled.
* @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power
* operation, if several modes of operation are supported these can be
* passed in the argument on a custom form, else just use argument 1
@@ -89,29 +83,35 @@
* 1 to indicate high level, argument 0 to indicate low level. (Please
* see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a
* discussion around this parameter.)
+ * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
+ * supplies, the argument to this parameter (on a custom format) tells
+ * the driver which alternative power source to use.
+ * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
+ * this parameter (on a custom format) tells the driver which alternative
+ * slew rate to use.
* @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
* you need to pass in custom configurations to the pin controller, use
* PIN_CONFIG_END+1 as the base offset.
*/
enum pin_config_param {
+ PIN_CONFIG_BIAS_BUS_HOLD,
PIN_CONFIG_BIAS_DISABLE,
PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
- PIN_CONFIG_BIAS_BUS_HOLD,
- PIN_CONFIG_BIAS_PULL_UP,
PIN_CONFIG_BIAS_PULL_DOWN,
PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
- PIN_CONFIG_DRIVE_PUSH_PULL,
+ PIN_CONFIG_BIAS_PULL_UP,
PIN_CONFIG_DRIVE_OPEN_DRAIN,
PIN_CONFIG_DRIVE_OPEN_SOURCE,
+ PIN_CONFIG_DRIVE_PUSH_PULL,
PIN_CONFIG_DRIVE_STRENGTH,
+ PIN_CONFIG_INPUT_DEBOUNCE,
PIN_CONFIG_INPUT_ENABLE,
- PIN_CONFIG_INPUT_SCHMITT_ENABLE,
PIN_CONFIG_INPUT_SCHMITT,
- PIN_CONFIG_INPUT_DEBOUNCE,
- PIN_CONFIG_POWER_SOURCE,
- PIN_CONFIG_SLEW_RATE,
+ PIN_CONFIG_INPUT_SCHMITT_ENABLE,
PIN_CONFIG_LOW_POWER_MODE,
PIN_CONFIG_OUTPUT,
+ PIN_CONFIG_POWER_SOURCE,
+ PIN_CONFIG_SLEW_RATE,
PIN_CONFIG_END = 0x7FFF,
};