diff options
Diffstat (limited to 'include/asm-sparc64/floppy.h')
| -rw-r--r-- | include/asm-sparc64/floppy.h | 83 |
1 files changed, 1 insertions, 82 deletions
diff --git a/include/asm-sparc64/floppy.h b/include/asm-sparc64/floppy.h index c47f58d6c15c..040d7962c5a3 100644 --- a/include/asm-sparc64/floppy.h +++ b/include/asm-sparc64/floppy.h @@ -558,82 +558,6 @@ static int __init ebus_fdthree_p(struct linux_ebus_device *edev) } #endif -#ifdef CONFIG_PCI -#undef ISA_FLOPPY_WORKS - -#ifdef ISA_FLOPPY_WORKS -static unsigned long __init isa_floppy_init(void) -{ - struct sparc_isa_bridge *isa_br; - struct sparc_isa_device *isa_dev = NULL; - - for_each_isa(isa_br) { - for_each_isadev(isa_dev, isa_br) { - if (!strcmp(isa_dev->prom_node->name, "dma")) { - struct sparc_isa_device *child = - isa_dev->child; - - while (child) { - if (!strcmp(child->prom_node->name, - "floppy")) { - isa_dev = child; - goto isa_done; - } - child = child->next; - } - } - } - } -isa_done: - if (!isa_dev) - return 0; - - /* We could use DMA on devices behind the ISA bridge, but... - * - * There is a slight problem. Normally on x86 kit the x86 processor - * delays I/O port instructions when the ISA bus "dma in progress" - * signal is active. Well, sparc64 systems do not monitor this - * signal thus we would need to block all I/O port accesses in software - * when a dma transfer is active for some device. - */ - - sun_fdc = (struct sun_flpy_controller *)isa_dev->resource.start; - FLOPPY_IRQ = isa_dev->irq; - - sun_fdops.fd_inb = sun_pci_fd_inb; - sun_fdops.fd_outb = sun_pci_fd_outb; - - can_use_virtual_dma = use_virtual_dma = 1; - sun_fdops.fd_enable_dma = sun_fd_enable_dma; - sun_fdops.fd_disable_dma = sun_fd_disable_dma; - sun_fdops.fd_set_dma_mode = sun_fd_set_dma_mode; - sun_fdops.fd_set_dma_addr = sun_fd_set_dma_addr; - sun_fdops.fd_set_dma_count = sun_fd_set_dma_count; - sun_fdops.get_dma_residue = sun_get_dma_residue; - - sun_fdops.fd_request_irq = sun_fd_request_irq; - sun_fdops.fd_free_irq = sun_fd_free_irq; - - /* Floppy eject is manual. Actually, could determine this - * via presence of 'manual' property in OBP node. - */ - sun_fdops.fd_eject = sun_pci_fd_eject; - - fdc_status = (unsigned long) &sun_fdc->status_82077; - - allowed_drive_mask = 0; - sun_floppy_types[0] = 0; - sun_floppy_types[1] = 4; - - sun_pci_broken_drive = 1; - sun_fdops.fd_outb = sun_pci_fd_broken_outb; - - return sun_floppy_types[0]; -} -#endif /* ISA_FLOPPY_WORKS */ - -#endif - static unsigned long __init sun_floppy_init(void) { char state[128]; @@ -667,13 +591,8 @@ static unsigned long __init sun_floppy_init(void) } } ebus_done: - if (!edev) { -#ifdef ISA_FLOPPY_WORKS - return isa_floppy_init(); -#else + if (!edev) return 0; -#endif - } state_prop = of_get_property(edev->prom_node, "status", NULL); if (state_prop && !strncmp(state_prop, "disabled", 8)) |