summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/scsi/NCR5380.c185
-rw-r--r--drivers/scsi/atari_NCR5380.c154
-rw-r--r--drivers/scsi/dtc.c8
-rw-r--r--drivers/scsi/g_NCR5380.c2
4 files changed, 178 insertions, 171 deletions
diff --git a/drivers/scsi/NCR5380.c b/drivers/scsi/NCR5380.c
index 1a6562b94bf7..8567d69709ce 100644
--- a/drivers/scsi/NCR5380.c
+++ b/drivers/scsi/NCR5380.c
@@ -951,85 +951,114 @@ static void NCR5380_main(struct work_struct *work)
#ifndef DONT_USE_INTR
/**
- * NCR5380_intr - generic NCR5380 irq handler
- * @irq: interrupt number
- * @dev_id: device info
- *
- * Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
- * from the disconnected queue, and restarting NCR5380_main()
- * as required.
- *
- * Locks: takes the needed instance locks
+ * NCR5380_intr - generic NCR5380 irq handler
+ * @irq: interrupt number
+ * @dev_id: device info
+ *
+ * Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
+ * from the disconnected queue, and restarting NCR5380_main()
+ * as required.
+ *
+ * The chip can assert IRQ in any of six different conditions. The IRQ flag
+ * is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
+ * Three of these six conditions are latched in the Bus and Status Register:
+ * - End of DMA (cleared by ending DMA Mode)
+ * - Parity error (cleared by reading RPIR)
+ * - Loss of BSY (cleared by reading RPIR)
+ * Two conditions have flag bits that are not latched:
+ * - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
+ * - Bus reset (non-maskable)
+ * The remaining condition has no flag bit at all:
+ * - Selection/reselection
+ *
+ * Hence, establishing the cause(s) of any interrupt is partly guesswork.
+ * In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
+ * claimed that "the design of the [DP8490] interrupt logic ensures
+ * interrupts will not be lost (they can be on the DP5380)."
+ * The L5380/53C80 datasheet from LOGIC Devices has more details.
+ *
+ * Checking for bus reset by reading RST is futile because of interrupt
+ * latency, but a bus reset will reset chip logic. Checking for parity error
+ * is unnecessary because that interrupt is never enabled. A Loss of BSY
+ * condition will clear DMA Mode. We can tell when this occurs because the
+ * the Busy Monitor interrupt is enabled together with DMA Mode.
*/
-static irqreturn_t NCR5380_intr(int dummy, void *dev_id)
+static irqreturn_t NCR5380_intr(int irq, void *dev_id)
{
struct Scsi_Host *instance = dev_id;
- struct NCR5380_hostdata *hostdata = (struct NCR5380_hostdata *) instance->hostdata;
- int done;
+ struct NCR5380_hostdata *hostdata = shost_priv(instance);
+ int handled = 0;
unsigned char basr;
unsigned long flags;
- dprintk(NDEBUG_INTR, "scsi : NCR5380 irq %d triggered\n",
- instance->irq);
+ spin_lock_irqsave(instance->host_lock, flags);
+
+ basr = NCR5380_read(BUS_AND_STATUS_REG);
+ if (basr & BASR_IRQ) {
+ unsigned char mr = NCR5380_read(MODE_REG);
+ unsigned char sr = NCR5380_read(STATUS_REG);
+
+ dprintk(NDEBUG_INTR, "scsi%d: IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
+ instance->host_no, irq, basr, sr, mr);
- do {
- done = 1;
- spin_lock_irqsave(instance->host_lock, flags);
- /* Look for pending interrupts */
- basr = NCR5380_read(BUS_AND_STATUS_REG);
- /* XXX dispatch to appropriate routine if found and done=0 */
- if (basr & BASR_IRQ) {
- NCR5380_dprint(NDEBUG_INTR, instance);
- if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
- done = 0;
- dprintk(NDEBUG_INTR, "scsi%d : SEL interrupt\n", instance->host_no);
- NCR5380_reselect(instance);
- (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- } else if (basr & BASR_PARITY_ERROR) {
- dprintk(NDEBUG_INTR, "scsi%d : PARITY interrupt\n", instance->host_no);
- (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- } else if ((NCR5380_read(STATUS_REG) & SR_RST) == SR_RST) {
- dprintk(NDEBUG_INTR, "scsi%d : RESET interrupt\n", instance->host_no);
- (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- } else {
#if defined(REAL_DMA)
- /*
- * We should only get PHASE MISMATCH and EOP interrupts
- * if we have DMA enabled, so do a sanity check based on
- * the current setting of the MODE register.
- */
+ if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
+ /* Probably End of DMA, Phase Mismatch or Loss of BSY.
+ * We ack IRQ after clearing Mode Register. Workarounds
+ * for End of DMA errata need to happen in DMA Mode.
+ */
- if ((NCR5380_read(MODE_REG) & MR_DMA) && ((basr & BASR_END_DMA_TRANSFER) || !(basr & BASR_PHASE_MATCH))) {
- int transferred;
+ dprintk(NDEBUG_INTR, "scsi%d: interrupt in DMA mode\n", intance->host_no);
- if (!hostdata->connected)
- panic("scsi%d : received end of DMA interrupt with no connected cmd\n", instance->hostno);
+ int transferred;
- transferred = (hostdata->dmalen - NCR5380_dma_residual(instance));
- hostdata->connected->SCp.this_residual -= transferred;
- hostdata->connected->SCp.ptr += transferred;
- hostdata->dmalen = 0;
+ if (!hostdata->connected)
+ panic("scsi%d : DMA interrupt with no connected cmd\n",
+ instance->hostno);
- (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-
- /* FIXME: we need to poll briefly then defer a workqueue task ! */
- NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG, BASR_ACK, 0, 2*HZ);
+ transferred = hostdata->dmalen - NCR5380_dma_residual(instance);
+ hostdata->connected->SCp.this_residual -= transferred;
+ hostdata->connected->SCp.ptr += transferred;
+ hostdata->dmalen = 0;
- NCR5380_write(MODE_REG, MR_BASE);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- }
-#else
- dprintk(NDEBUG_INTR, "scsi : unknown interrupt, BASR 0x%X, MR 0x%X, SR 0x%x\n", basr, NCR5380_read(MODE_REG), NCR5380_read(STATUS_REG));
- (void) NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-#endif
+ /* FIXME: we need to poll briefly then defer a workqueue task ! */
+ NCR5380_poll_politely(hostdata, BUS_AND_STATUS_REG, BASR_ACK, 0, 2 * HZ);
+
+ NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
+ NCR5380_write(MODE_REG, MR_BASE);
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+ } else
+#endif /* REAL_DMA */
+ if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
+ (sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
+ /* Probably reselected */
+ NCR5380_write(SELECT_ENABLE_REG, 0);
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+
+ dprintk(NDEBUG_INTR, "scsi%d: interrupt with SEL and IO\n",
+ instance->host_no);
+
+ if (!hostdata->connected) {
+ NCR5380_reselect(instance);
+ queue_work(hostdata->work_q, &hostdata->main_task);
}
- } /* if BASR_IRQ */
- spin_unlock_irqrestore(instance->host_lock, flags);
- if(!done)
- queue_work(hostdata->work_q, &hostdata->main_task);
- } while (!done);
- return IRQ_HANDLED;
+ if (!hostdata->connected)
+ NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
+ } else {
+ /* Probably Bus Reset */
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+
+ dprintk(NDEBUG_INTR, "scsi%d: unknown interrupt\n", instance->host_no);
+ }
+ handled = 1;
+ } else {
+ shost_printk(KERN_NOTICE, instance, "interrupt without IRQ bit\n");
+ }
+
+ spin_unlock_irqrestore(instance->host_lock, flags);
+
+ return IRQ_RETVAL(handled);
}
#endif
@@ -1218,8 +1247,9 @@ static int NCR5380_select(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
NCR5380_reselect(instance);
+ if (!hostdata->connected)
+ NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
printk("scsi%d : reselection after won arbitration?\n", instance->host_no);
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
return -1;
}
@@ -1563,9 +1593,10 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase
NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
#ifdef REAL_DMA
- NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_ENABLE_EOP_INTR | MR_MONITOR_BSY);
+ NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
+ MR_ENABLE_EOP_INTR);
#elif defined(REAL_DMA_POLL)
- NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE);
+ NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY);
#else
/*
* Note : on my sample board, watch-dog timeouts occurred when interrupts
@@ -1573,13 +1604,11 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase
* before the setting of DMA mode to after transfer of the last byte.
*/
- /* KLL May need eop and parity in 53c400 */
if (hostdata->flags & FLAG_NCR53C400)
- NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE |
- MR_ENABLE_PAR_CHECK | MR_ENABLE_PAR_INTR |
- MR_ENABLE_EOP_INTR | MR_MONITOR_BSY);
+ NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
+ MR_ENABLE_EOP_INTR);
else
- NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE);
+ NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY);
#endif /* def REAL_DMA */
dprintk(NDEBUG_DMA, "scsi%d : mode reg = 0x%X\n", instance->host_no, NCR5380_read(MODE_REG));
@@ -1768,16 +1797,7 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance, unsigned char *phase
}
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
- if ((!(p & SR_IO)) && (hostdata->flags & FLAG_NCR53C400)) {
- dprintk(NDEBUG_C400_PWRITE, "53C400w: Checking for IRQ\n");
- if (NCR5380_read(BUS_AND_STATUS_REG) & BASR_IRQ) {
- dprintk(NDEBUG_C400_PWRITE, "53C400w: got it, reading reset interrupt reg\n");
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- } else {
- printk("53C400w: IRQ NOT THERE!\n");
- }
- }
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
*data = d + c;
*count = 0;
*phase = NCR5380_read(STATUS_REG) & PHASE_MASK;
@@ -2269,7 +2289,6 @@ static void NCR5380_dma_complete(NCR5380_instance * instance) {
NCR5380_poll_politely(instance, BUS_AND_STATUS_REG, BASR_ACK, 0, 5*HZ);
- NCR5380_write(MODE_REG, MR_BASE);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
/*
diff --git a/drivers/scsi/atari_NCR5380.c b/drivers/scsi/atari_NCR5380.c
index 48e3d76e39e3..c8c216a9f448 100644
--- a/drivers/scsi/atari_NCR5380.c
+++ b/drivers/scsi/atari_NCR5380.c
@@ -1144,12 +1144,6 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
int saved_data = 0, overrun = 0;
unsigned char p;
- if (!hostdata->connected) {
- printk(KERN_WARNING "scsi%d: received end of DMA interrupt with "
- "no connected cmd\n", HOSTNO);
- return;
- }
-
if (hostdata->read_overruns) {
p = hostdata->connected->SCp.phase;
if (p & SR_IO) {
@@ -1164,10 +1158,6 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
}
}
- dprintk(NDEBUG_DMA, "scsi%d: real DMA transfer complete, basr 0x%X, sr 0x%X\n",
- HOSTNO, NCR5380_read(BUS_AND_STATUS_REG),
- NCR5380_read(STATUS_REG));
-
#if defined(CONFIG_SUN3)
if ((sun3scsi_dma_finish(rq_data_dir(hostdata->connected->request)))) {
pr_err("scsi%d: overrun in UDC counter -- not prepared to deal with this!\n",
@@ -1186,9 +1176,9 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
}
#endif
- (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(MODE_REG, MR_BASE);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
transferred = hostdata->dma_len - NCR5380_dma_residual(instance);
hostdata->dma_len = 0;
@@ -1227,83 +1217,97 @@ static void NCR5380_dma_complete(struct Scsi_Host *instance)
* Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
* from the disconnected queue, and restarting NCR5380_main()
* as required.
+ *
+ * The chip can assert IRQ in any of six different conditions. The IRQ flag
+ * is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
+ * Three of these six conditions are latched in the Bus and Status Register:
+ * - End of DMA (cleared by ending DMA Mode)
+ * - Parity error (cleared by reading RPIR)
+ * - Loss of BSY (cleared by reading RPIR)
+ * Two conditions have flag bits that are not latched:
+ * - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
+ * - Bus reset (non-maskable)
+ * The remaining condition has no flag bit at all:
+ * - Selection/reselection
+ *
+ * Hence, establishing the cause(s) of any interrupt is partly guesswork.
+ * In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
+ * claimed that "the design of the [DP8490] interrupt logic ensures
+ * interrupts will not be lost (they can be on the DP5380)."
+ * The L5380/53C80 datasheet from LOGIC Devices has more details.
+ *
+ * Checking for bus reset by reading RST is futile because of interrupt
+ * latency, but a bus reset will reset chip logic. Checking for parity error
+ * is unnecessary because that interrupt is never enabled. A Loss of BSY
+ * condition will clear DMA Mode. We can tell when this occurs because the
+ * the Busy Monitor interrupt is enabled together with DMA Mode.
*/
static irqreturn_t NCR5380_intr(int irq, void *dev_id)
{
struct Scsi_Host *instance = dev_id;
struct NCR5380_hostdata *hostdata = shost_priv(instance);
- int done = 1, handled = 0;
+ int handled = 0;
unsigned char basr;
- dprintk(NDEBUG_INTR, "scsi%d: NCR5380 irq triggered\n", HOSTNO);
-
- /* Look for pending interrupts */
basr = NCR5380_read(BUS_AND_STATUS_REG);
- dprintk(NDEBUG_INTR, "scsi%d: BASR=%02x\n", HOSTNO, basr);
- /* dispatch to appropriate routine if found and done=0 */
if (basr & BASR_IRQ) {
- NCR5380_dprint(NDEBUG_INTR, instance);
- if ((NCR5380_read(STATUS_REG) & (SR_SEL|SR_IO)) == (SR_SEL|SR_IO)) {
- done = 0;
- dprintk(NDEBUG_INTR, "scsi%d: SEL interrupt\n", HOSTNO);
- NCR5380_reselect(instance);
- (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- } else if (basr & BASR_PARITY_ERROR) {
- dprintk(NDEBUG_INTR, "scsi%d: PARITY interrupt\n", HOSTNO);
- (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- } else if ((NCR5380_read(STATUS_REG) & SR_RST) == SR_RST) {
- dprintk(NDEBUG_INTR, "scsi%d: RESET interrupt\n", HOSTNO);
- (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- } else {
- /*
- * The rest of the interrupt conditions can occur only during a
- * DMA transfer
- */
+ unsigned char mr = NCR5380_read(MODE_REG);
+ unsigned char sr = NCR5380_read(STATUS_REG);
+
+ dprintk(NDEBUG_INTR, "scsi%d: IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
+ HOSTNO, irq, basr, sr, mr);
#if defined(REAL_DMA)
- /*
- * We should only get PHASE MISMATCH and EOP interrupts if we have
- * DMA enabled, so do a sanity check based on the current setting
- * of the MODE register.
+ if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
+ /* Probably End of DMA, Phase Mismatch or Loss of BSY.
+ * We ack IRQ after clearing Mode Register. Workarounds
+ * for End of DMA errata need to happen in DMA Mode.
*/
- if ((NCR5380_read(MODE_REG) & MR_DMA_MODE) &&
- ((basr & BASR_END_DMA_TRANSFER) ||
- !(basr & BASR_PHASE_MATCH))) {
+ dprintk(NDEBUG_INTR, "scsi%d: interrupt in DMA mode\n", HOSTNO);
- dprintk(NDEBUG_INTR, "scsi%d: PHASE MISM or EOP interrupt\n", HOSTNO);
- NCR5380_dma_complete( instance );
- done = 0;
- } else
+ if (hostdata->connected) {
+ NCR5380_dma_complete(instance);
+ queue_work(hostdata->work_q, &hostdata->main_task);
+ } else {
+ NCR5380_write(MODE_REG, MR_BASE);
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+ }
+ } else
#endif /* REAL_DMA */
- {
-/* MS: Ignore unknown phase mismatch interrupts (caused by EOP interrupt) */
- if (basr & BASR_PHASE_MATCH)
- dprintk(NDEBUG_INTR, "scsi%d: unknown interrupt, "
- "BASR 0x%x, MR 0x%x, SR 0x%x\n",
- HOSTNO, basr, NCR5380_read(MODE_REG),
- NCR5380_read(STATUS_REG));
- (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+ if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
+ (sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
+ /* Probably reselected */
+ NCR5380_write(SELECT_ENABLE_REG, 0);
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+
+ dprintk(NDEBUG_INTR, "scsi%d: interrupt with SEL and IO\n",
+ HOSTNO);
+
+ if (!hostdata->connected) {
+ NCR5380_reselect(instance);
+ queue_work(hostdata->work_q, &hostdata->main_task);
+ }
+ if (!hostdata->connected)
+ NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
+ } else {
+ /* Probably Bus Reset */
+ NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+
+ dprintk(NDEBUG_INTR, "scsi%d: unknown interrupt\n", HOSTNO);
#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_DMA_ENABLE;
+ dregs->csr |= CSR_DMA_ENABLE;
#endif
- }
- } /* if !(SELECTION || PARITY) */
+ }
handled = 1;
- } /* BASR & IRQ */ else {
- printk(KERN_NOTICE "scsi%d: interrupt without IRQ bit set in BASR, "
- "BASR 0x%X, MR 0x%X, SR 0x%x\n", HOSTNO, basr,
- NCR5380_read(MODE_REG), NCR5380_read(STATUS_REG));
- (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
+ } else {
+ shost_printk(KERN_NOTICE, instance, "interrupt without IRQ bit\n");
#ifdef SUN3_SCSI_VME
dregs->csr |= CSR_DMA_ENABLE;
#endif
}
- if (!done)
- queue_work(hostdata->work_q, &hostdata->main_task);
-
return IRQ_RETVAL(handled);
}
@@ -1509,9 +1513,10 @@ static int NCR5380_select(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
NCR5380_reselect(instance);
+ if (!hostdata->connected)
+ NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
printk(KERN_ERR "scsi%d: reselection after won arbitration?\n",
HOSTNO);
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
return -1;
}
@@ -1871,19 +1876,14 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance,
/* send start chain */
sun3scsi_dma_start(c, *data);
+ NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
+ NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
+ MR_ENABLE_EOP_INTR);
if (p & SR_IO) {
- NCR5380_write(TARGET_COMMAND_REG, 1);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(INITIATOR_COMMAND_REG, 0);
- NCR5380_write(MODE_REG,
- (NCR5380_read(MODE_REG) | MR_DMA_MODE | MR_ENABLE_EOP_INTR));
NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
} else {
- NCR5380_write(TARGET_COMMAND_REG, 0);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
NCR5380_write(INITIATOR_COMMAND_REG, ICR_ASSERT_DATA);
- NCR5380_write(MODE_REG,
- (NCR5380_read(MODE_REG) | MR_DMA_MODE | MR_ENABLE_EOP_INTR));
NCR5380_write(START_DMA_SEND_REG, 0);
}
@@ -1912,10 +1912,8 @@ static int NCR5380_transfer_dma(struct Scsi_Host *instance,
c, (p & SR_IO) ? "to" : "from", d);
NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
-
-#ifdef REAL_DMA
- NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_ENABLE_EOP_INTR | MR_MONITOR_BSY);
-#endif /* def REAL_DMA */
+ NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
+ MR_ENABLE_EOP_INTR);
if (!(hostdata->flags & FLAG_LATE_DMA_SETUP)) {
/* On the Medusa, it is a must to initialize the DMA before
@@ -2389,10 +2387,10 @@ static void NCR5380_information_transfer(struct Scsi_Host *instance)
#endif
hostdata->connected = NULL;
cmd->result = DID_ERROR << 16;
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
maybe_release_dma_irq(instance);
local_irq_restore(flags);
cmd->scsi_done(cmd);
+ NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
return;
}
msgout = NOP;
diff --git a/drivers/scsi/dtc.c b/drivers/scsi/dtc.c
index 60bffb34ecfb..3af4f69c199c 100644
--- a/drivers/scsi/dtc.c
+++ b/drivers/scsi/dtc.c
@@ -334,8 +334,6 @@ static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst,
struct NCR5380_hostdata *hostdata = shost_priv(instance);
i = 0;
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
if (instance->irq == NO_IRQ)
NCR5380_write(DTC_CONTROL_REG, CSR_DIR_READ);
else
@@ -357,9 +355,7 @@ static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst,
rtrc(4);
while (!(NCR5380_read(DTC_CONTROL_REG) & D_CR_ACCESS))
++i;
- NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
rtrc(0);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
if (i > hostdata->spin_max_r)
hostdata->spin_max_r = i;
return (0);
@@ -383,9 +379,6 @@ static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src,
int i;
struct NCR5380_hostdata *hostdata = shost_priv(instance);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- NCR5380_write(MODE_REG, MR_ENABLE_EOP_INTR | MR_DMA_MODE);
- /* set direction (write) */
if (instance->irq == NO_IRQ)
NCR5380_write(DTC_CONTROL_REG, 0);
else
@@ -410,7 +403,6 @@ static inline int NCR5380_pwrite(struct Scsi_Host *instance, unsigned char *src,
++i;
rtrc(7);
/* Check for parity error here. fixme. */
- NCR5380_write(MODE_REG, 0); /* Clear the operating mode */
rtrc(0);
if (i > hostdata->spin_max_w)
hostdata->spin_max_w = i;
diff --git a/drivers/scsi/g_NCR5380.c b/drivers/scsi/g_NCR5380.c
index 258bc2ff0d1c..4124f053d1b3 100644
--- a/drivers/scsi/g_NCR5380.c
+++ b/drivers/scsi/g_NCR5380.c
@@ -594,8 +594,6 @@ static inline int NCR5380_pread(struct Scsi_Host *instance, unsigned char *dst,
if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))
printk(KERN_ERR "53C400r: no end dma signal\n");
- NCR5380_write(MODE_REG, MR_BASE);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
return 0;
}
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-31 15:34:26 +0000