diff options
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/media/video/Kconfig | 8 | ||||
| -rw-r--r-- | drivers/media/video/Makefile | 1 | ||||
| -rw-r--r-- | drivers/media/video/omap1_camera.c | 1702 |
3 files changed, 1711 insertions, 0 deletions
diff --git a/drivers/media/video/Kconfig b/drivers/media/video/Kconfig index 27b728fce7a7..b89d0fda40fc 100644 --- a/drivers/media/video/Kconfig +++ b/drivers/media/video/Kconfig @@ -822,6 +822,14 @@ config VIDEO_SH_MOBILE_CEU ---help--- This is a v4l2 driver for the SuperH Mobile CEU Interface +config VIDEO_OMAP1 + tristate "OMAP1 Camera Interface driver" + depends on VIDEO_DEV && ARCH_OMAP1 && SOC_CAMERA + select VIDEOBUF_DMA_CONTIG + select VIDEOBUF_DMA_SG + ---help--- + This is a v4l2 driver for the TI OMAP1 camera interface + config VIDEO_OMAP2 tristate "OMAP2 Camera Capture Interface driver" depends on VIDEO_DEV && ARCH_OMAP2 diff --git a/drivers/media/video/Makefile b/drivers/media/video/Makefile index 118196c06fcd..557ad1f3aeb4 100644 --- a/drivers/media/video/Makefile +++ b/drivers/media/video/Makefile @@ -157,6 +157,7 @@ obj-$(CONFIG_VIDEO_MX3) += mx3_camera.o obj-$(CONFIG_VIDEO_PXA27x) += pxa_camera.o obj-$(CONFIG_VIDEO_SH_MOBILE_CSI2) += sh_mobile_csi2.o obj-$(CONFIG_VIDEO_SH_MOBILE_CEU) += sh_mobile_ceu_camera.o +obj-$(CONFIG_VIDEO_OMAP1) += omap1_camera.o obj-$(CONFIG_VIDEO_SAMSUNG_S5P_FIMC) += s5p-fimc/ obj-$(CONFIG_ARCH_DAVINCI) += davinci/ diff --git a/drivers/media/video/omap1_camera.c b/drivers/media/video/omap1_camera.c new file mode 100644 index 000000000000..7c30e62b50db --- /dev/null +++ b/drivers/media/video/omap1_camera.c @@ -0,0 +1,1702 @@ +/* + * V4L2 SoC Camera driver for OMAP1 Camera Interface + * + * Copyright (C) 2010, Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> + * + * Based on V4L2 Driver for i.MXL/i.MXL camera (CSI) host + * Copyright (C) 2008, Paulius Zaleckas <paulius.zaleckas@teltonika.lt> + * Copyright (C) 2009, Darius Augulis <augulis.darius@gmail.com> + * + * Based on PXA SoC camera driver + * Copyright (C) 2006, Sascha Hauer, Pengutronix + * Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de> + * + * Hardware specific bits initialy based on former work by Matt Callow + * drivers/media/video/omap/omap1510cam.c + * Copyright (C) 2006 Matt Callow + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + + +#include <linux/clk.h> +#include <linux/dma-mapping.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/version.h> + +#include <media/omap1_camera.h> +#include <media/soc_camera.h> +#include <media/soc_mediabus.h> +#include <media/videobuf-dma-contig.h> +#include <media/videobuf-dma-sg.h> + +#include <plat/dma.h> + + +#define DRIVER_NAME "omap1-camera" +#define VERSION_CODE KERNEL_VERSION(0, 0, 1) + + +/* + * --------------------------------------------------------------------------- + * OMAP1 Camera Interface registers + * --------------------------------------------------------------------------- + */ + +#define REG_CTRLCLOCK 0x00 +#define REG_IT_STATUS 0x04 +#define REG_MODE 0x08 +#define REG_STATUS 0x0C +#define REG_CAMDATA 0x10 +#define REG_GPIO 0x14 +#define REG_PEAK_COUNTER 0x18 + +/* CTRLCLOCK bit shifts */ +#define LCLK_EN BIT(7) +#define DPLL_EN BIT(6) +#define MCLK_EN BIT(5) +#define CAMEXCLK_EN BIT(4) +#define POLCLK BIT(3) +#define FOSCMOD_SHIFT 0 +#define FOSCMOD_MASK (0x7 << FOSCMOD_SHIFT) +#define FOSCMOD_12MHz 0x0 +#define FOSCMOD_6MHz 0x2 +#define FOSCMOD_9_6MHz 0x4 +#define FOSCMOD_24MHz 0x5 +#define FOSCMOD_8MHz 0x6 + +/* IT_STATUS bit shifts */ +#define DATA_TRANSFER BIT(5) +#define FIFO_FULL BIT(4) +#define H_DOWN BIT(3) +#define H_UP BIT(2) +#define V_DOWN BIT(1) +#define V_UP BIT(0) + +/* MODE bit shifts */ +#define RAZ_FIFO BIT(18) +#define EN_FIFO_FULL BIT(17) +#define EN_NIRQ BIT(16) +#define THRESHOLD_SHIFT 9 +#define THRESHOLD_MASK (0x7f << THRESHOLD_SHIFT) +#define DMA BIT(8) +#define EN_H_DOWN BIT(7) +#define EN_H_UP BIT(6) +#define EN_V_DOWN BIT(5) +#define EN_V_UP BIT(4) +#define ORDERCAMD BIT(3) + +#define IRQ_MASK (EN_V_UP | EN_V_DOWN | EN_H_UP | EN_H_DOWN | \ + EN_NIRQ | EN_FIFO_FULL) + +/* STATUS bit shifts */ +#define HSTATUS BIT(1) +#define VSTATUS BIT(0) + +/* GPIO bit shifts */ +#define CAM_RST BIT(0) + +/* end of OMAP1 Camera Interface registers */ + + +#define SOCAM_BUS_FLAGS (SOCAM_MASTER | \ + SOCAM_HSYNC_ACTIVE_HIGH | SOCAM_VSYNC_ACTIVE_HIGH | \ + SOCAM_PCLK_SAMPLE_RISING | SOCAM_PCLK_SAMPLE_FALLING | \ + SOCAM_DATA_ACTIVE_HIGH | SOCAM_DATAWIDTH_8) + + +#define FIFO_SIZE ((THRESHOLD_MASK >> THRESHOLD_SHIFT) + 1) +#define FIFO_SHIFT __fls(FIFO_SIZE) + +#define DMA_BURST_SHIFT (1 + OMAP_DMA_DATA_BURST_4) +#define DMA_BURST_SIZE (1 << DMA_BURST_SHIFT) + +#define DMA_ELEMENT_SHIFT OMAP_DMA_DATA_TYPE_S32 +#define DMA_ELEMENT_SIZE (1 << DMA_ELEMENT_SHIFT) + +#define DMA_FRAME_SHIFT_CONTIG (FIFO_SHIFT - 1) +#define DMA_FRAME_SHIFT_SG DMA_BURST_SHIFT + +#define DMA_FRAME_SHIFT(x) ((x) == OMAP1_CAM_DMA_CONTIG ? \ + DMA_FRAME_SHIFT_CONTIG : \ + DMA_FRAME_SHIFT_SG) +#define DMA_FRAME_SIZE(x) (1 << DMA_FRAME_SHIFT(x)) +#define DMA_SYNC OMAP_DMA_SYNC_FRAME +#define THRESHOLD_LEVEL DMA_FRAME_SIZE + + +#define MAX_VIDEO_MEM 4 /* arbitrary video memory limit in MB */ + + +/* + * Structures + */ + +/* buffer for one video frame */ +struct omap1_cam_buf { + struct videobuf_buffer vb; + enum v4l2_mbus_pixelcode code; + int inwork; + struct scatterlist *sgbuf; + int sgcount; + int bytes_left; + enum videobuf_state result; +}; + +struct omap1_cam_dev { + struct soc_camera_host soc_host; + struct soc_camera_device *icd; + struct clk *clk; + + unsigned int irq; + void __iomem *base; + + int dma_ch; + + struct omap1_cam_platform_data *pdata; + struct resource *res; + unsigned long pflags; + unsigned long camexclk; + + struct list_head capture; + + /* lock used to protect videobuf */ + spinlock_t lock; + + /* Pointers to DMA buffers */ + struct omap1_cam_buf *active; + struct omap1_cam_buf *ready; + + enum omap1_cam_vb_mode vb_mode; + int (*mmap_mapper)(struct videobuf_queue *q, + struct videobuf_buffer *buf, + struct vm_area_struct *vma); + + u32 reg_cache[0]; +}; + + +static void cam_write(struct omap1_cam_dev *pcdev, u16 reg, u32 val) +{ + pcdev->reg_cache[reg / sizeof(u32)] = val; + __raw_writel(val, pcdev->base + reg); +} + +static u32 cam_read(struct omap1_cam_dev *pcdev, u16 reg, bool from_cache) +{ + return !from_cache ? __raw_readl(pcdev->base + reg) : + pcdev->reg_cache[reg / sizeof(u32)]; +} + +#define CAM_READ(pcdev, reg) \ + cam_read(pcdev, REG_##reg, false) +#define CAM_WRITE(pcdev, reg, val) \ + cam_write(pcdev, REG_##reg, val) +#define CAM_READ_CACHE(pcdev, reg) \ + cam_read(pcdev, REG_##reg, true) + +/* + * Videobuf operations + */ +static int omap1_videobuf_setup(struct videobuf_queue *vq, unsigned int *count, + unsigned int *size) +{ + struct soc_camera_device *icd = vq->priv_data; + int bytes_per_line = soc_mbus_bytes_per_line(icd->user_width, + icd->current_fmt->host_fmt); + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + + if (bytes_per_line < 0) + return bytes_per_line; + + *size = bytes_per_line * icd->user_height; + + if (!*count || *count < OMAP1_CAMERA_MIN_BUF_COUNT(pcdev->vb_mode)) + *count = OMAP1_CAMERA_MIN_BUF_COUNT(pcdev->vb_mode); + + if (*size * *count > MAX_VIDEO_MEM * 1024 * 1024) + *count = (MAX_VIDEO_MEM * 1024 * 1024) / *size; + + dev_dbg(icd->dev.parent, + "%s: count=%d, size=%d\n", __func__, *count, *size); + + return 0; +} + +static void free_buffer(struct videobuf_queue *vq, struct omap1_cam_buf *buf, + enum omap1_cam_vb_mode vb_mode) +{ + struct videobuf_buffer *vb = &buf->vb; + + BUG_ON(in_interrupt()); + + videobuf_waiton(vb, 0, 0); + + if (vb_mode == OMAP1_CAM_DMA_CONTIG) { + videobuf_dma_contig_free(vq, vb); + } else { + struct soc_camera_device *icd = vq->priv_data; + struct device *dev = icd->dev.parent; + struct videobuf_dmabuf *dma = videobuf_to_dma(vb); + + videobuf_dma_unmap(dev, dma); + videobuf_dma_free(dma); + } + + vb->state = VIDEOBUF_NEEDS_INIT; +} + +static int omap1_videobuf_prepare(struct videobuf_queue *vq, + struct videobuf_buffer *vb, enum v4l2_field field) +{ + struct soc_camera_device *icd = vq->priv_data; + struct omap1_cam_buf *buf = container_of(vb, struct omap1_cam_buf, vb); + int bytes_per_line = soc_mbus_bytes_per_line(icd->user_width, + icd->current_fmt->host_fmt); + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + int ret; + + if (bytes_per_line < 0) + return bytes_per_line; + + WARN_ON(!list_empty(&vb->queue)); + + BUG_ON(NULL == icd->current_fmt); + + buf->inwork = 1; + + if (buf->code != icd->current_fmt->code || vb->field != field || + vb->width != icd->user_width || + vb->height != icd->user_height) { + buf->code = icd->current_fmt->code; + vb->width = icd->user_width; + vb->height = icd->user_height; + vb->field = field; + vb->state = VIDEOBUF_NEEDS_INIT; + } + + vb->size = bytes_per_line * vb->height; + + if (vb->baddr && vb->bsize < vb->size) { + ret = -EINVAL; + goto out; + } + + if (vb->state == VIDEOBUF_NEEDS_INIT) { + ret = videobuf_iolock(vq, vb, NULL); + if (ret) + goto fail; + + vb->state = VIDEOBUF_PREPARED; + } + buf->inwork = 0; + + return 0; +fail: + free_buffer(vq, buf, pcdev->vb_mode); +out: + buf->inwork = 0; + return ret; +} + +static void set_dma_dest_params(int dma_ch, struct omap1_cam_buf *buf, + enum omap1_cam_vb_mode vb_mode) +{ + dma_addr_t dma_addr; + unsigned int block_size; + + if (vb_mode == OMAP1_CAM_DMA_CONTIG) { + dma_addr = videobuf_to_dma_contig(&buf->vb); + block_size = buf->vb.size; + } else { + if (WARN_ON(!buf->sgbuf)) { + buf->result = VIDEOBUF_ERROR; + return; + } + dma_addr = sg_dma_address(buf->sgbuf); + if (WARN_ON(!dma_addr)) { + buf->sgbuf = NULL; + buf->result = VIDEOBUF_ERROR; + return; + } + block_size = sg_dma_len(buf->sgbuf); + if (WARN_ON(!block_size)) { + buf->sgbuf = NULL; + buf->result = VIDEOBUF_ERROR; + return; + } + if (unlikely(buf->bytes_left < block_size)) + block_size = buf->bytes_left; + if (WARN_ON(dma_addr & (DMA_FRAME_SIZE(vb_mode) * + DMA_ELEMENT_SIZE - 1))) { + dma_addr = ALIGN(dma_addr, DMA_FRAME_SIZE(vb_mode) * + DMA_ELEMENT_SIZE); + block_size &= ~(DMA_FRAME_SIZE(vb_mode) * + DMA_ELEMENT_SIZE - 1); + } + buf->bytes_left -= block_size; + buf->sgcount++; + } + + omap_set_dma_dest_params(dma_ch, + OMAP_DMA_PORT_EMIFF, OMAP_DMA_AMODE_POST_INC, dma_addr, 0, 0); + omap_set_dma_transfer_params(dma_ch, + OMAP_DMA_DATA_TYPE_S32, DMA_FRAME_SIZE(vb_mode), + block_size >> (DMA_FRAME_SHIFT(vb_mode) + DMA_ELEMENT_SHIFT), + DMA_SYNC, 0, 0); +} + +static struct omap1_cam_buf *prepare_next_vb(struct omap1_cam_dev *pcdev) +{ + struct omap1_cam_buf *buf; + + /* + * If there is already a buffer pointed out by the pcdev->ready, + * (re)use it, otherwise try to fetch and configure a new one. + */ + buf = pcdev->ready; + if (!buf) { + if (list_empty(&pcdev->capture)) + return buf; + buf = list_entry(pcdev->capture.next, + struct omap1_cam_buf, vb.queue); + buf->vb.state = VIDEOBUF_ACTIVE; + pcdev->ready = buf; + list_del_init(&buf->vb.queue); + } + + if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) { + /* + * In CONTIG mode, we can safely enter next buffer parameters + * into the DMA programming register set after the DMA + * has already been activated on the previous buffer + */ + set_dma_dest_params(pcdev->dma_ch, buf, pcdev->vb_mode); + } else { + /* + * In SG mode, the above is not safe since there are probably + * a bunch of sgbufs from previous sglist still pending. + * Instead, mark the sglist fresh for the upcoming + * try_next_sgbuf(). + */ + buf->sgbuf = NULL; + } + + return buf; +} + +static struct scatterlist *try_next_sgbuf(int dma_ch, struct omap1_cam_buf *buf) +{ + struct scatterlist *sgbuf; + + if (likely(buf->sgbuf)) { + /* current sglist is active */ + if (unlikely(!buf->bytes_left)) { + /* indicate sglist complete */ + sgbuf = NULL; + } else { + /* process next sgbuf */ + sgbuf = sg_next(buf->sgbuf); + if (WARN_ON(!sgbuf)) { + buf->result = VIDEOBUF_ERROR; + } else if (WARN_ON(!sg_dma_len(sgbuf))) { + sgbuf = NULL; + buf->result = VIDEOBUF_ERROR; + } + } + buf->sgbuf = sgbuf; + } else { + /* sglist is fresh, initialize it before using */ + struct videobuf_dmabuf *dma = videobuf_to_dma(&buf->vb); + + sgbuf = dma->sglist; + if (!(WARN_ON(!sgbuf))) { + buf->sgbuf = sgbuf; + buf->sgcount = 0; + buf->bytes_left = buf->vb.size; + buf->result = VIDEOBUF_DONE; + } + } + if (sgbuf) + /* + * Put our next sgbuf parameters (address, size) + * into the DMA programming register set. + */ + set_dma_dest_params(dma_ch, buf, OMAP1_CAM_DMA_SG); + + return sgbuf; +} + +static void start_capture(struct omap1_cam_dev *pcdev) +{ + struct omap1_cam_buf *buf = pcdev->active; + u32 ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK); + u32 mode = CAM_READ_CACHE(pcdev, MODE) & ~EN_V_DOWN; + + if (WARN_ON(!buf)) + return; + + /* + * Enable start of frame interrupt, which we will use for activating + * our end of frame watchdog when capture actually starts. + */ + mode |= EN_V_UP; + + if (unlikely(ctrlclock & LCLK_EN)) + /* stop pixel clock before FIFO reset */ + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN); + /* reset FIFO */ + CAM_WRITE(pcdev, MODE, mode | RAZ_FIFO); + + omap_start_dma(pcdev->dma_ch); + + if (pcdev->vb_mode == OMAP1_CAM_DMA_SG) { + /* + * In SG mode, it's a good moment for fetching next sgbuf + * from the current sglist and, if available, already putting + * its parameters into the DMA programming register set. + */ + try_next_sgbuf(pcdev->dma_ch, buf); + } + + /* (re)enable pixel clock */ + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock | LCLK_EN); + /* release FIFO reset */ + CAM_WRITE(pcdev, MODE, mode); +} + +static void suspend_capture(struct omap1_cam_dev *pcdev) +{ + u32 ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK); + + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN); + omap_stop_dma(pcdev->dma_ch); +} + +static void disable_capture(struct omap1_cam_dev *pcdev) +{ + u32 mode = CAM_READ_CACHE(pcdev, MODE); + + CAM_WRITE(pcdev, MODE, mode & ~(IRQ_MASK | DMA)); +} + +static void omap1_videobuf_queue(struct videobuf_queue *vq, + struct videobuf_buffer *vb) +{ + struct soc_camera_device *icd = vq->priv_data; + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + struct omap1_cam_buf *buf; + u32 mode; + + list_add_tail(&vb->queue, &pcdev->capture); + vb->state = VIDEOBUF_QUEUED; + + if (pcdev->active) { + /* + * Capture in progress, so don't touch pcdev->ready even if + * empty. Since the transfer of the DMA programming register set + * content to the DMA working register set is done automatically + * by the DMA hardware, this can pretty well happen while we + * are keeping the lock here. Levae fetching it from the queue + * to be done when a next DMA interrupt occures instead. + */ + return; + } + + WARN_ON(pcdev->ready); + + buf = prepare_next_vb(pcdev); + if (WARN_ON(!buf)) + return; + + pcdev->active = buf; + pcdev->ready = NULL; + + dev_dbg(icd->dev.parent, + "%s: capture not active, setup FIFO, start DMA\n", __func__); + mode = CAM_READ_CACHE(pcdev, MODE) & ~THRESHOLD_MASK; + mode |= THRESHOLD_LEVEL(pcdev->vb_mode) << THRESHOLD_SHIFT; + CAM_WRITE(pcdev, MODE, mode | EN_FIFO_FULL | DMA); + + if (pcdev->vb_mode == OMAP1_CAM_DMA_SG) { + /* + * In SG mode, the above prepare_next_vb() didn't actually + * put anything into the DMA programming register set, + * so we have to do it now, before activating DMA. + */ + try_next_sgbuf(pcdev->dma_ch, buf); + } + + start_capture(pcdev); +} + +static void omap1_videobuf_release(struct videobuf_queue *vq, + struct videobuf_buffer *vb) +{ + struct omap1_cam_buf *buf = + container_of(vb, struct omap1_cam_buf, vb); + struct soc_camera_device *icd = vq->priv_data; + struct device *dev = icd->dev.parent; + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + + switch (vb->state) { + case VIDEOBUF_DONE: + dev_dbg(dev, "%s (done)\n", __func__); + break; + case VIDEOBUF_ACTIVE: + dev_dbg(dev, "%s (active)\n", __func__); + break; + case VIDEOBUF_QUEUED: + dev_dbg(dev, "%s (queued)\n", __func__); + break; + case VIDEOBUF_PREPARED: + dev_dbg(dev, "%s (prepared)\n", __func__); + break; + default: + dev_dbg(dev, "%s (unknown %d)\n", __func__, vb->state); + break; + } + + free_buffer(vq, buf, pcdev->vb_mode); +} + +static void videobuf_done(struct omap1_cam_dev *pcdev, + enum videobuf_state result) +{ + struct omap1_cam_buf *buf = pcdev->active; + struct videobuf_buffer *vb; + struct device *dev = pcdev->icd->dev.parent; + + if (WARN_ON(!buf)) { + suspend_capture(pcdev); + disable_capture(pcdev); + return; + } + + if (result == VIDEOBUF_ERROR) + suspend_capture(pcdev); + + vb = &buf->vb; + if (waitqueue_active(&vb->done)) { + if (!pcdev->ready && result != VIDEOBUF_ERROR) { + /* + * No next buffer has been entered into the DMA + * programming register set on time (could be done only + * while the previous DMA interurpt was processed, not + * later), so the last DMA block, be it a whole buffer + * if in CONTIG or its last sgbuf if in SG mode, is + * about to be reused by the just autoreinitialized DMA + * engine, and overwritten with next frame data. Best we + * can do is stopping the capture as soon as possible, + * hopefully before the next frame start. + */ + suspend_capture(pcdev); + } + vb->state = result; + do_gettimeofday(&vb->ts); + if (result != VIDEOBUF_ERROR) + vb->field_count++; + wake_up(&vb->done); + + /* shift in next buffer */ + buf = pcdev->ready; + pcdev->active = buf; + pcdev->ready = NULL; + + if (!buf) { + /* + * No next buffer was ready on time (see above), so + * indicate error condition to force capture restart or + * stop, depending on next buffer already queued or not. + */ + result = VIDEOBUF_ERROR; + prepare_next_vb(pcdev); + + buf = pcdev->ready; + pcdev->active = buf; + pcdev->ready = NULL; + } + } else if (pcdev->ready) { + /* + * In both CONTIG and SG mode, the DMA engine has possibly + * been already autoreinitialized with the preprogrammed + * pcdev->ready buffer. We can either accept this fact + * and just swap the buffers, or provoke an error condition + * and restart capture. The former seems less intrusive. + */ + dev_dbg(dev, "%s: nobody waiting on videobuf, swap with next\n", + __func__); + pcdev->active = pcdev->ready; + + if (pcdev->vb_mode == OMAP1_CAM_DMA_SG) { + /* + * In SG mode, we have to make sure that the buffer we + * are putting back into the pcdev->ready is marked + * fresh. + */ + buf->sgbuf = NULL; + } + pcdev->ready = buf; + + buf = pcdev->active; + } else { + /* + * No next buffer has been entered into + * the DMA programming register set on time. + */ + if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) { + /* + * In CONTIG mode, the DMA engine has already been + * reinitialized with the current buffer. Best we can do + * is not touching it. + */ + dev_dbg(dev, + "%s: nobody waiting on videobuf, reuse it\n", + __func__); + } else { + /* + * In SG mode, the DMA engine has just been + * autoreinitialized with the last sgbuf from the + * current list. Restart capture in order to transfer + * next frame start into the first sgbuf, not the last + * one. + */ + if (result != VIDEOBUF_ERROR) { + suspend_capture(pcdev); + result = VIDEOBUF_ERROR; + } + } + } + + if (!buf) { + dev_dbg(dev, "%s: no more videobufs, stop capture\n", __func__); + disable_capture(pcdev); + return; + } + + if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) { + /* + * In CONTIG mode, the current buffer parameters had already + * been entered into the DMA programming register set while the + * buffer was fetched with prepare_next_vb(), they may have also + * been transfered into the runtime set and already active if + * the DMA still running. + */ + } else { + /* In SG mode, extra steps are required */ + if (result == VIDEOBUF_ERROR) + /* make sure we (re)use sglist from start on error */ + buf->sgbuf = NULL; + + /* + * In any case, enter the next sgbuf parameters into the DMA + * programming register set. They will be used either during + * nearest DMA autoreinitialization or, in case of an error, + * on DMA startup below. + */ + try_next_sgbuf(pcdev->dma_ch, buf); + } + + if (result == VIDEOBUF_ERROR) { + dev_dbg(dev, "%s: videobuf error; reset FIFO, restart DMA\n", + __func__); + start_capture(pcdev); + /* + * In SG mode, the above also resulted in the next sgbuf + * parameters being entered into the DMA programming register + * set, making them ready for next DMA autoreinitialization. + */ + } + + /* + * Finally, try fetching next buffer. + * In CONTIG mode, it will also enter it into the DMA programming + * register set, making it ready for next DMA autoreinitialization. + */ + prepare_next_vb(pcdev); +} + +static void dma_isr(int channel, unsigned short status, void *data) +{ + struct omap1_cam_dev *pcdev = data; + struct omap1_cam_buf *buf = pcdev->active; + unsigned long flags; + + spin_lock_irqsave(&pcdev->lock, flags); + + if (WARN_ON(!buf)) { + suspend_capture(pcdev); + disable_capture(pcdev); + goto out; + } + + if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) { + /* + * In CONTIG mode, assume we have just managed to collect the + * whole frame, hopefully before our end of frame watchdog is + * triggered. Then, all we have to do is disabling the watchdog + * for this frame, and calling videobuf_done() with success + * indicated. + */ + CAM_WRITE(pcdev, MODE, + CAM_READ_CACHE(pcdev, MODE) & ~EN_V_DOWN); + videobuf_done(pcdev, VIDEOBUF_DONE); + } else { + /* + * In SG mode, we have to process every sgbuf from the current + * sglist, one after another. + */ + if (buf->sgbuf) { + /* + * Current sglist not completed yet, try fetching next + * sgbuf, hopefully putting it into the DMA programming + * register set, making it ready for next DMA + * autoreinitialization. + */ + try_next_sgbuf(pcdev->dma_ch, buf); + if (buf->sgbuf) + goto out; + + /* + * No more sgbufs left in the current sglist. This + * doesn't mean that the whole videobuffer is already + * complete, but only that the last sgbuf from the + * current sglist is about to be filled. It will be + * ready on next DMA interrupt, signalled with the + * buf->sgbuf set back to NULL. + */ + if (buf->result != VIDEOBUF_ERROR) { + /* + * Video frame collected without errors so far, + * we can prepare for collecting a next one + * as soon as DMA gets autoreinitialized + * after the current (last) sgbuf is completed. + */ + buf = prepare_next_vb(pcdev); + if (!buf) + goto out; + + try_next_sgbuf(pcdev->dma_ch, buf); + goto out; + } + } + /* end of videobuf */ + videobuf_done(pcdev, buf->result); + } + +out: + spin_unlock_irqrestore(&pcdev->lock, flags); +} + +static irqreturn_t cam_isr(int irq, void *data) +{ + struct omap1_cam_dev *pcdev = data; + struct device *dev = pcdev->icd->dev.parent; + struct omap1_cam_buf *buf = pcdev->active; + u32 it_status; + unsigned long flags; + + it_status = CAM_READ(pcdev, IT_STATUS); + if (!it_status) + return IRQ_NONE; + + spin_lock_irqsave(&pcdev->lock, flags); + + if (WARN_ON(!buf)) { + dev_warn(dev, "%s: unhandled camera interrupt, status == " + "%#x\n", __func__, it_status); + suspend_capture(pcdev); + disable_capture(pcdev); + goto out; + } + + if (unlikely(it_status & FIFO_FULL)) { + dev_warn(dev, "%s: FIFO overflow\n", __func__); + + } else if (it_status & V_DOWN) { + /* end of video frame watchdog */ + if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) { + /* + * In CONTIG mode, the watchdog is disabled with + * successful DMA end of block interrupt, and reenabled + * on next frame start. If we get here, there is nothing + * to check, we must be out of sync. + */ + } else { + if (buf->sgcount == 2) { + /* + * If exactly 2 sgbufs from the next sglist have + * been programmed into the DMA engine (the + * frist one already transfered into the DMA + * runtime register set, the second one still + * in the programming set), then we are in sync. + */ + goto out; + } + } + dev_notice(dev, "%s: unexpected end of video frame\n", + __func__); + + } else if (it_status & V_UP) { + u32 mode; + + if (pcdev->vb_mode == OMAP1_CAM_DMA_CONTIG) { + /* + * In CONTIG mode, we need this interrupt every frame + * in oredr to reenable our end of frame watchdog. + */ + mode = CAM_READ_CACHE(pcdev, MODE); + } else { + /* + * In SG mode, the below enabled end of frame watchdog + * is kept on permanently, so we can turn this one shot + * setup off. + */ + mode = CAM_READ_CACHE(pcdev, MODE) & ~EN_V_UP; + } + + if (!(mode & EN_V_DOWN)) { + /* (re)enable end of frame watchdog interrupt */ + mode |= EN_V_DOWN; + } + CAM_WRITE(pcdev, MODE, mode); + goto out; + + } else { + dev_warn(dev, "%s: unhandled camera interrupt, status == %#x\n", + __func__, it_status); + goto out; + } + + videobuf_done(pcdev, VIDEOBUF_ERROR); +out: + spin_unlock_irqrestore(&pcdev->lock, flags); + return IRQ_HANDLED; +} + +static struct videobuf_queue_ops omap1_videobuf_ops = { + .buf_setup = omap1_videobuf_setup, + .buf_prepare = omap1_videobuf_prepare, + .buf_queue = omap1_videobuf_queue, + .buf_release = omap1_videobuf_release, +}; + + +/* + * SOC Camera host operations + */ + +static void sensor_reset(struct omap1_cam_dev *pcdev, bool reset) +{ + /* apply/release camera sensor reset if requested by platform data */ + if (pcdev->pflags & OMAP1_CAMERA_RST_HIGH) + CAM_WRITE(pcdev, GPIO, reset); + else if (pcdev->pflags & OMAP1_CAMERA_RST_LOW) + CAM_WRITE(pcdev, GPIO, !reset); +} + +/* + * The following two functions absolutely depend on the fact, that + * there can be only one camera on OMAP1 camera sensor interface + */ +static int omap1_cam_add_device(struct soc_camera_device *icd) +{ + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + u32 ctrlclock; + + if (pcdev->icd) + return -EBUSY; + + clk_enable(pcdev->clk); + + /* setup sensor clock */ + ctrlclock = CAM_READ(pcdev, CTRLCLOCK); + ctrlclock &= ~(CAMEXCLK_EN | MCLK_EN | DPLL_EN); + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock); + + ctrlclock &= ~FOSCMOD_MASK; + switch (pcdev->camexclk) { + case 6000000: + ctrlclock |= CAMEXCLK_EN | FOSCMOD_6MHz; + break; + case 8000000: + ctrlclock |= CAMEXCLK_EN | FOSCMOD_8MHz | DPLL_EN; + break; + case 9600000: + ctrlclock |= CAMEXCLK_EN | FOSCMOD_9_6MHz | DPLL_EN; + break; + case 12000000: + ctrlclock |= CAMEXCLK_EN | FOSCMOD_12MHz; + break; + case 24000000: + ctrlclock |= CAMEXCLK_EN | FOSCMOD_24MHz | DPLL_EN; + default: + break; + } + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~DPLL_EN); + + /* enable internal clock */ + ctrlclock |= MCLK_EN; + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock); + + sensor_reset(pcdev, false); + + pcdev->icd = icd; + + dev_dbg(icd->dev.parent, "OMAP1 Camera driver attached to camera %d\n", + icd->devnum); + return 0; +} + +static void omap1_cam_remove_device(struct soc_camera_device *icd) +{ + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + u32 ctrlclock; + + BUG_ON(icd != pcdev->icd); + + suspend_capture(pcdev); + disable_capture(pcdev); + + sensor_reset(pcdev, true); + + /* disable and release system clocks */ + ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK); + ctrlclock &= ~(MCLK_EN | DPLL_EN | CAMEXCLK_EN); + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock); + + ctrlclock = (ctrlclock & ~FOSCMOD_MASK) | FOSCMOD_12MHz; + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock); + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock | MCLK_EN); + + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~MCLK_EN); + + clk_disable(pcdev->clk); + + pcdev->icd = NULL; + + dev_dbg(icd->dev.parent, + "OMAP1 Camera driver detached from camera %d\n", icd->devnum); +} + +/* Duplicate standard formats based on host capability of byte swapping */ +static const struct soc_mbus_pixelfmt omap1_cam_formats[] = { + [V4L2_MBUS_FMT_UYVY8_2X8] = { + .fourcc = V4L2_PIX_FMT_YUYV, + .name = "YUYV", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, + [V4L2_MBUS_FMT_VYUY8_2X8] = { + .fourcc = V4L2_PIX_FMT_YVYU, + .name = "YVYU", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, + [V4L2_MBUS_FMT_YUYV8_2X8] = { + .fourcc = V4L2_PIX_FMT_UYVY, + .name = "UYVY", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, + [V4L2_MBUS_FMT_YVYU8_2X8] = { + .fourcc = V4L2_PIX_FMT_VYUY, + .name = "VYUY", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, + [V4L2_MBUS_FMT_RGB555_2X8_PADHI_BE] = { + .fourcc = V4L2_PIX_FMT_RGB555, + .name = "RGB555", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, + [V4L2_MBUS_FMT_RGB555_2X8_PADHI_LE] = { + .fourcc = V4L2_PIX_FMT_RGB555X, + .name = "RGB555X", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, + [V4L2_MBUS_FMT_RGB565_2X8_BE] = { + .fourcc = V4L2_PIX_FMT_RGB565, + .name = "RGB565", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, + [V4L2_MBUS_FMT_RGB565_2X8_LE] = { + .fourcc = V4L2_PIX_FMT_RGB565X, + .name = "RGB565X", + .bits_per_sample = 8, + .packing = SOC_MBUS_PACKING_2X8_PADHI, + .order = SOC_MBUS_ORDER_BE, + }, +}; + +static int omap1_cam_get_formats(struct soc_camera_device *icd, + unsigned int idx, struct soc_camera_format_xlate *xlate) +{ + struct v4l2_subdev *sd = soc_camera_to_subdev(icd); + struct device *dev = icd->dev.parent; + int formats = 0, ret; + enum v4l2_mbus_pixelcode code; + const struct soc_mbus_pixelfmt *fmt; + + ret = v4l2_subdev_call(sd, video, enum_mbus_fmt, idx, &code); + if (ret < 0) + /* No more formats */ + return 0; + + fmt = soc_mbus_get_fmtdesc(code); + if (!fmt) { + dev_err(dev, "%s: invalid format code #%d: %d\n", __func__, + idx, code); + return 0; + } + + /* Check support for the requested bits-per-sample */ + if (fmt->bits_per_sample != 8) + return 0; + + switch (code) { + case V4L2_MBUS_FMT_YUYV8_2X8: + case V4L2_MBUS_FMT_YVYU8_2X8: + case V4L2_MBUS_FMT_UYVY8_2X8: + case V4L2_MBUS_FMT_VYUY8_2X8: + case V4L2_MBUS_FMT_RGB555_2X8_PADHI_BE: + case V4L2_MBUS_FMT_RGB555_2X8_PADHI_LE: + case V4L2_MBUS_FMT_RGB565_2X8_BE: + case V4L2_MBUS_FMT_RGB565_2X8_LE: + formats++; + if (xlate) { + xlate->host_fmt = &omap1_cam_formats[code]; + xlate->code = code; + xlate++; + dev_dbg(dev, "%s: providing format %s " + "as byte swapped code #%d\n", __func__, + omap1_cam_formats[code].name, code); + } + default: + if (xlate) + dev_dbg(dev, "%s: providing format %s " + "in pass-through mode\n", __func__, + fmt->name); + } + formats++; + if (xlate) { + xlate->host_fmt = fmt; + xlate->code = code; + xlate++; + } + + return formats; +} + +static bool is_dma_aligned(s32 bytes_per_line, unsigned int height, + enum omap1_cam_vb_mode vb_mode) +{ + int size = bytes_per_line * height; + + return IS_ALIGNED(bytes_per_line, DMA_ELEMENT_SIZE) && + IS_ALIGNED(size, DMA_FRAME_SIZE(vb_mode) * DMA_ELEMENT_SIZE); +} + +static int dma_align(int *width, int *height, + const struct soc_mbus_pixelfmt *fmt, + enum omap1_cam_vb_mode vb_mode, bool enlarge) +{ + s32 bytes_per_line = soc_mbus_bytes_per_line(*width, fmt); + + if (bytes_per_line < 0) + return bytes_per_line; + + if (!is_dma_aligned(bytes_per_line, *height, vb_mode)) { + unsigned int pxalign = __fls(bytes_per_line / *width); + unsigned int salign = DMA_FRAME_SHIFT(vb_mode) + + DMA_ELEMENT_SHIFT - pxalign; + unsigned int incr = enlarge << salign; + + v4l_bound_align_image(width, 1, *width + incr, 0, + height, 1, *height + incr, 0, salign); + return 0; + } + return 1; +} + +#define subdev_call_with_sense(pcdev, dev, icd, sd, function, args...) \ +({ \ + struct soc_camera_sense sense = { \ + .master_clock = pcdev->camexclk, \ + .pixel_clock_max = 0, \ + }; \ + int __ret; \ + \ + if (pcdev->pdata) \ + sense.pixel_clock_max = pcdev->pdata->lclk_khz_max * 1000; \ + icd->sense = &sense; \ + __ret = v4l2_subdev_call(sd, video, function, ##args); \ + icd->sense = NULL; \ + \ + if (sense.flags & SOCAM_SENSE_PCLK_CHANGED) { \ + if (sense.pixel_clock > sense.pixel_clock_max) { \ + dev_err(dev, "%s: pixel clock %lu " \ + "set by the camera too high!\n", \ + __func__, sense.pixel_clock); \ + __ret = -EINVAL; \ + } \ + } \ + __ret; \ +}) + +static int set_mbus_format(struct omap1_cam_dev *pcdev, struct device *dev, + struct soc_camera_device *icd, struct v4l2_subdev *sd, + struct v4l2_mbus_framefmt *mf, + const struct soc_camera_format_xlate *xlate) +{ + s32 bytes_per_line; + int ret = subdev_call_with_sense(pcdev, dev, icd, sd, s_mbus_fmt, mf); + + if (ret < 0) { + dev_err(dev, "%s: s_mbus_fmt failed\n", __func__); + return ret; + } + + if (mf->code != xlate->code) { + dev_err(dev, "%s: unexpected pixel code change\n", __func__); + return -EINVAL; + } + + bytes_per_line = soc_mbus_bytes_per_line(mf->width, xlate->host_fmt); + if (bytes_per_line < 0) { + dev_err(dev, "%s: soc_mbus_bytes_per_line() failed\n", + __func__); + return bytes_per_line; + } + + if (!is_dma_aligned(bytes_per_line, mf->height, pcdev->vb_mode)) { + dev_err(dev, "%s: resulting geometry %ux%u not DMA aligned\n", + __func__, mf->width, mf->height); + return -EINVAL; + } + return 0; +} + +static int omap1_cam_set_crop(struct soc_camera_device *icd, + struct v4l2_crop *crop) +{ + struct v4l2_rect *rect = &crop->c; + const struct soc_camera_format_xlate *xlate = icd->current_fmt; + struct v4l2_subdev *sd = soc_camera_to_subdev(icd); + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + struct device *dev = icd->dev.parent; + struct v4l2_mbus_framefmt mf; + int ret; + + ret = subdev_call_with_sense(pcdev, dev, icd, sd, s_crop, crop); + if (ret < 0) { + dev_warn(dev, "%s: failed to crop to %ux%u@%u:%u\n", __func__, + rect->width, rect->height, rect->left, rect->top); + return ret; + } + + ret = v4l2_subdev_call(sd, video, g_mbus_fmt, &mf); + if (ret < 0) { + dev_warn(dev, "%s: failed to fetch current format\n", __func__); + return ret; + } + + ret = dma_align(&mf.width, &mf.height, xlate->host_fmt, pcdev->vb_mode, + false); + if (ret < 0) { + dev_err(dev, "%s: failed to align %ux%u %s with DMA\n", + __func__, mf.width, mf.height, + xlate->host_fmt->name); + return ret; + } + + if (!ret) { + /* sensor returned geometry not DMA aligned, trying to fix */ + ret = set_mbus_format(pcdev, dev, icd, sd, &mf, xlate); + if (ret < 0) { + dev_err(dev, "%s: failed to set format\n", __func__); + return ret; + } + } + + icd->user_width = mf.width; + icd->user_height = mf.height; + + return 0; +} + +static int omap1_cam_set_fmt(struct soc_camera_device *icd, + struct v4l2_format *f) +{ + struct v4l2_subdev *sd = soc_camera_to_subdev(icd); + const struct soc_camera_format_xlate *xlate; + struct device *dev = icd->dev.parent; + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + struct v4l2_pix_format *pix = &f->fmt.pix; + struct v4l2_mbus_framefmt mf; + int ret; + + xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat); + if (!xlate) { + dev_warn(dev, "%s: format %#x not found\n", __func__, + pix->pixelformat); + return -EINVAL; + } + + mf.width = pix->width; + mf.height = pix->height; + mf.field = pix->field; + mf.colorspace = pix->colorspace; + mf.code = xlate->code; + + ret = dma_align(&mf.width, &mf.height, xlate->host_fmt, pcdev->vb_mode, + true); + if (ret < 0) { + dev_err(dev, "%s: failed to align %ux%u %s with DMA\n", + __func__, pix->width, pix->height, + xlate->host_fmt->name); + return ret; + } + + ret = set_mbus_format(pcdev, dev, icd, sd, &mf, xlate); + if (ret < 0) { + dev_err(dev, "%s: failed to set format\n", __func__); + return ret; + } + + pix->width = mf.width; + pix->height = mf.height; + pix->field = mf.field; + pix->colorspace = mf.colorspace; + icd->current_fmt = xlate; + + return 0; +} + +static int omap1_cam_try_fmt(struct soc_camera_device *icd, + struct v4l2_format *f) +{ + struct v4l2_subdev *sd = soc_camera_to_subdev(icd); + const struct soc_camera_format_xlate *xlate; + struct v4l2_pix_format *pix = &f->fmt.pix; + struct v4l2_mbus_framefmt mf; + int ret; + /* TODO: limit to mx1 hardware capabilities */ + + xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat); + if (!xlate) { + dev_warn(icd->dev.parent, "Format %#x not found\n", + pix->pixelformat); + return -EINVAL; + } + + mf.width = pix->width; + mf.height = pix->height; + mf.field = pix->field; + mf.colorspace = pix->colorspace; + mf.code = xlate->code; + + /* limit to sensor capabilities */ + ret = v4l2_subdev_call(sd, video, try_mbus_fmt, &mf); + if (ret < 0) + return ret; + + pix->width = mf.width; + pix->height = mf.height; + pix->field = mf.field; + pix->colorspace = mf.colorspace; + + return 0; +} + +static bool sg_mode; + +/* + * Local mmap_mapper wrapper, + * used for detecting videobuf-dma-contig buffer allocation failures + * and switching to videobuf-dma-sg automatically for future attempts. + */ +static int omap1_cam_mmap_mapper(struct videobuf_queue *q, + struct videobuf_buffer *buf, + struct vm_area_struct *vma) +{ + struct soc_camera_device *icd = q->priv_data; + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + int ret; + + ret = pcdev->mmap_mapper(q, buf, vma); + + if (ret == -ENOMEM) + sg_mode = true; + + return ret; +} + +static void omap1_cam_init_videobuf(struct videobuf_queue *q, + struct soc_camera_device *icd) +{ + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + + if (!sg_mode) + videobuf_queue_dma_contig_init(q, &omap1_videobuf_ops, + icd->dev.parent, &pcdev->lock, + V4L2_BUF_TYPE_VIDEO_CAPTURE, V4L2_FIELD_NONE, + sizeof(struct omap1_cam_buf), icd); + else + videobuf_queue_sg_init(q, &omap1_videobuf_ops, + icd->dev.parent, &pcdev->lock, + V4L2_BUF_TYPE_VIDEO_CAPTURE, V4L2_FIELD_NONE, + sizeof(struct omap1_cam_buf), icd); + + /* use videobuf mode (auto)selected with the module parameter */ + pcdev->vb_mode = sg_mode ? OMAP1_CAM_DMA_SG : OMAP1_CAM_DMA_CONTIG; + + /* + * Ensure we substitute the videobuf-dma-contig version of the + * mmap_mapper() callback with our own wrapper, used for switching + * automatically to videobuf-dma-sg on buffer allocation failure. + */ + if (!sg_mode && q->int_ops->mmap_mapper != omap1_cam_mmap_mapper) { + pcdev->mmap_mapper = q->int_ops->mmap_mapper; + q->int_ops->mmap_mapper = omap1_cam_mmap_mapper; + } +} + +static int omap1_cam_reqbufs(struct soc_camera_file *icf, + struct v4l2_requestbuffers *p) +{ + int i; + + /* + * This is for locking debugging only. I removed spinlocks and now I + * check whether .prepare is ever called on a linked buffer, or whether + * a dma IRQ can occur for an in-work or unlinked buffer. Until now + * it hadn't triggered + */ + for (i = 0; i < p->count; i++) { + struct omap1_cam_buf *buf = container_of(icf->vb_vidq.bufs[i], + struct omap1_cam_buf, vb); + buf->inwork = 0; + INIT_LIST_HEAD(&buf->vb.queue); + } + + return 0; +} + +static int omap1_cam_querycap(struct soc_camera_host *ici, + struct v4l2_capability *cap) +{ + /* cap->name is set by the friendly caller:-> */ + strlcpy(cap->card, "OMAP1 Camera", sizeof(cap->card)); + cap->version = VERSION_CODE; + cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING; + + return 0; +} + +static int omap1_cam_set_bus_param(struct soc_camera_device *icd, + __u32 pixfmt) +{ + struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); + struct omap1_cam_dev *pcdev = ici->priv; + struct device *dev = icd->dev.parent; + const struct soc_camera_format_xlate *xlate; + const struct soc_mbus_pixelfmt *fmt; + unsigned long camera_flags, common_flags; + u32 ctrlclock, mode; + int ret; + + camera_flags = icd->ops->query_bus_param(icd); + + common_flags = soc_camera_bus_param_compatible(camera_flags, + SOCAM_BUS_FLAGS); + if (!common_flags) + return -EINVAL; + + /* Make choices, possibly based on platform configuration */ + if ((common_flags & SOCAM_PCLK_SAMPLE_RISING) && + (common_flags & SOCAM_PCLK_SAMPLE_FALLING)) { + if (!pcdev->pdata || + pcdev->pdata->flags & OMAP1_CAMERA_LCLK_RISING) + common_flags &= ~SOCAM_PCLK_SAMPLE_FALLING; + else + common_flags &= ~SOCAM_PCLK_SAMPLE_RISING; + } + + ret = icd->ops->set_bus_param(icd, common_flags); + if (ret < 0) + return ret; + + ctrlclock = CAM_READ_CACHE(pcdev, CTRLCLOCK); + if (ctrlclock & LCLK_EN) + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN); + + if (common_flags & SOCAM_PCLK_SAMPLE_RISING) { + dev_dbg(dev, "CTRLCLOCK_REG |= POLCLK\n"); + ctrlclock |= POLCLK; + } else { + dev_dbg(dev, "CTRLCLOCK_REG &= ~POLCLK\n"); + ctrlclock &= ~POLCLK; + } + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock & ~LCLK_EN); + + if (ctrlclock & LCLK_EN) + CAM_WRITE(pcdev, CTRLCLOCK, ctrlclock); + + /* select bus endianess */ + xlate = soc_camera_xlate_by_fourcc(icd, pixfmt); + fmt = xlate->host_fmt; + + mode = CAM_READ(pcdev, MODE) & ~(RAZ_FIFO | IRQ_MASK | DMA); + if (fmt->order == SOC_MBUS_ORDER_LE) { + dev_dbg(dev, "MODE_REG &= ~ORDERCAMD\n"); + CAM_WRITE(pcdev, MODE, mode & ~ORDERCAMD); + } else { + dev_dbg(dev, "MODE_REG |= ORDERCAMD\n"); + CAM_WRITE(pcdev, MODE, mode | ORDERCAMD); + } + + return 0; +} + +static unsigned int omap1_cam_poll(struct file *file, poll_table *pt) +{ + struct soc_camera_file *icf = file->private_data; + struct omap1_cam_buf *buf; + + buf = list_entry(icf->vb_vidq.stream.next, struct omap1_cam_buf, + vb.stream); + + poll_wait(file, &buf->vb.done, pt); + + if (buf->vb.state == VIDEOBUF_DONE || + buf->vb.state == VIDEOBUF_ERROR) + return POLLIN | POLLRDNORM; + + return 0; +} + +static struct soc_camera_host_ops omap1_host_ops = { + .owner = THIS_MODULE, + .add = omap1_cam_add_device, + .remove = omap1_cam_remove_device, + .get_formats = omap1_cam_get_formats, + .set_crop = omap1_cam_set_crop, + .set_fmt = omap1_cam_set_fmt, + .try_fmt = omap1_cam_try_fmt, + .init_videobuf = omap1_cam_init_videobuf, + .reqbufs = omap1_cam_reqbufs, + .querycap = omap1_cam_querycap, + .set_bus_param = omap1_cam_set_bus_param, + .poll = omap1_cam_poll, +}; + +static int __init omap1_cam_probe(struct platform_device *pdev) +{ + struct omap1_cam_dev *pcdev; + struct resource *res; + struct clk *clk; + void __iomem *base; + unsigned int irq; + int err = 0; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + irq = platform_get_irq(pdev, 0); + if (!res || (int)irq <= 0) { + err = -ENODEV; + goto exit; + } + + clk = clk_get(&pdev->dev, "armper_ck"); + if (IS_ERR(clk)) { + err = PTR_ERR(clk); + goto exit; + } + + pcdev = kzalloc(sizeof(*pcdev) + resource_size(res), GFP_KERNEL); + if (!pcdev) { + dev_err(&pdev->dev, "Could not allocate pcdev\n"); + err = -ENOMEM; + goto exit_put_clk; + } + + pcdev->res = res; + pcdev->clk = clk; + + pcdev->pdata = pdev->dev.platform_data; + pcdev->pflags = pcdev->pdata->flags; + + if (pcdev->pdata) + pcdev->camexclk = pcdev->pdata->camexclk_khz * 1000; + + switch (pcdev->camexclk) { + case 6000000: + case 8000000: + case 9600000: + case 12000000: + case 24000000: + break; + default: + dev_warn(&pdev->dev, + "Incorrect sensor clock frequency %ld kHz, " + "should be one of 0, 6, 8, 9.6, 12 or 24 MHz, " + "please correct your platform data\n", + pcdev->pdata->camexclk_khz); + pcdev->camexclk = 0; + case 0: + dev_info(&pdev->dev, + "Not providing sensor clock\n"); + } + + INIT_LIST_HEAD(&pcdev->capture); + spin_lock_init(&pcdev->lock); + + /* + * Request the region. + */ + if (!request_mem_region(res->start, resource_size(res), DRIVER_NAME)) { + err = -EBUSY; + goto exit_kfree; + } + + base = ioremap(res->start, resource_size(res)); + if (!base) { + err = -ENOMEM; + goto exit_release; + } + pcdev->irq = irq; + pcdev->base = base; + + sensor_reset(pcdev, true); + + err = omap_request_dma(OMAP_DMA_CAMERA_IF_RX, DRIVER_NAME, + dma_isr, (void *)pcdev, &pcdev->dma_ch); + if (err < 0) { + dev_err(&pdev->dev, "Can't request DMA for OMAP1 Camera\n"); + err = -EBUSY; + goto exit_iounmap; + } + dev_dbg(&pdev->dev, "got DMA channel %d\n", pcdev->dma_ch); + + /* preconfigure DMA */ + omap_set_dma_src_params(pcdev->dma_ch, OMAP_DMA_PORT_TIPB, + OMAP_DMA_AMODE_CONSTANT, res->start + REG_CAMDATA, + 0, 0); + omap_set_dma_dest_burst_mode(pcdev->dma_ch, OMAP_DMA_DATA_BURST_4); + /* setup DMA autoinitialization */ + omap_dma_link_lch(pcdev->dma_ch, pcdev->dma_ch); + + err = request_irq(pcdev->irq, cam_isr, 0, DRIVER_NAME, pcdev); + if (err) { + dev_err(&pdev->dev, "Camera interrupt register failed\n"); + goto exit_free_dma; + } + + pcdev->soc_host.drv_name = DRIVER_NAME; + pcdev->soc_host.ops = &omap1_host_ops; + pcdev->soc_host.priv = pcdev; + pcdev->soc_host.v4l2_dev.dev = &pdev->dev; + pcdev->soc_host.nr = pdev->id; + + err = soc_camera_host_register(&pcdev->soc_host); + if (err) + goto exit_free_irq; + + dev_info(&pdev->dev, "OMAP1 Camera Interface driver loaded\n"); + + return 0; + +exit_free_irq: + free_irq(pcdev->irq, pcdev); +exit_free_dma: + omap_free_dma(pcdev->dma_ch); +exit_iounmap: + iounmap(base); +exit_release: + release_mem_region(res->start, resource_size(res)); +exit_kfree: + kfree(pcdev); +exit_put_clk: + clk_put(clk); +exit: + return err; +} + +static int __exit omap1_cam_remove(struct platform_device *pdev) +{ + struct soc_camera_host *soc_host = to_soc_camera_host(&pdev->dev); + struct omap1_cam_dev *pcdev = container_of(soc_host, + struct omap1_cam_dev, soc_host); + struct resource *res; + + free_irq(pcdev->irq, pcdev); + + omap_free_dma(pcdev->dma_ch); + + soc_camera_host_unregister(soc_host); + + iounmap(pcdev->base); + + res = pcdev->res; + release_mem_region(res->start, resource_size(res)); + + kfree(pcdev); + + clk_put(pcdev->clk); + + dev_info(&pdev->dev, "OMAP1 Camera Interface driver unloaded\n"); + + return 0; +} + +static struct platform_driver omap1_cam_driver = { + .driver = { + .name = DRIVER_NAME, + }, + .probe = omap1_cam_probe, + .remove = __exit_p(omap1_cam_remove), +}; + +static int __init omap1_cam_init(void) +{ + return platform_driver_register(&omap1_cam_driver); +} +module_init(omap1_cam_init); + +static void __exit omap1_cam_exit(void) +{ + platform_driver_unregister(&omap1_cam_driver); +} +module_exit(omap1_cam_exit); + +module_param(sg_mode, bool, 0644); +MODULE_PARM_DESC(sg_mode, "videobuf mode, 0: dma-contig (default), 1: dma-sg"); + +MODULE_DESCRIPTION("OMAP1 Camera Interface driver"); +MODULE_AUTHOR("Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:" DRIVER_NAME); |