summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet')
-rw-r--r--drivers/net/ethernet/intel/igb/e1000_82575.c43
-rw-r--r--drivers/net/ethernet/intel/igb/e1000_defines.h7
-rw-r--r--drivers/net/ethernet/intel/igb/e1000_mac.c124
3 files changed, 166 insertions, 8 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c
index db40b68819d8..fdaaf2709d0a 100644
--- a/drivers/net/ethernet/intel/igb/e1000_82575.c
+++ b/drivers/net/ethernet/intel/igb/e1000_82575.c
@@ -1028,6 +1028,15 @@ static s32 igb_check_for_link_82575(struct e1000_hw *hw)
* continue to check for link.
*/
hw->mac.get_link_status = !hw->mac.serdes_has_link;
+
+ /* Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control
+ * settings because we may have had to re-autoneg with a
+ * different link partner.
+ */
+ ret_val = igb_config_fc_after_link_up(hw);
+ if (ret_val)
+ hw_dbg("Error configuring flow control\n");
} else {
ret_val = igb_check_for_copper_link(hw);
}
@@ -1345,7 +1354,7 @@ out:
**/
static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
{
- u32 ctrl_ext, ctrl_reg, reg;
+ u32 ctrl_ext, ctrl_reg, reg, anadv_reg;
bool pcs_autoneg;
s32 ret_val = E1000_SUCCESS;
u16 data;
@@ -1433,27 +1442,45 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw)
reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP |
E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK);
- /*
- * We force flow control to prevent the CTRL register values from being
- * overwritten by the autonegotiated flow control values
- */
- reg |= E1000_PCS_LCTL_FORCE_FCTRL;
-
if (pcs_autoneg) {
/* Set PCS register for autoneg */
reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */
E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */
+
+ /* Disable force flow control for autoneg */
+ reg &= ~E1000_PCS_LCTL_FORCE_FCTRL;
+
+ /* Configure flow control advertisement for autoneg */
+ anadv_reg = rd32(E1000_PCS_ANADV);
+ anadv_reg &= ~(E1000_TXCW_ASM_DIR | E1000_TXCW_PAUSE);
+ switch (hw->fc.requested_mode) {
+ case e1000_fc_full:
+ case e1000_fc_rx_pause:
+ anadv_reg |= E1000_TXCW_ASM_DIR;
+ anadv_reg |= E1000_TXCW_PAUSE;
+ break;
+ case e1000_fc_tx_pause:
+ anadv_reg |= E1000_TXCW_ASM_DIR;
+ break;
+ default:
+ break;
+ }
+ wr32(E1000_PCS_ANADV, anadv_reg);
+
hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg);
} else {
/* Set PCS register for forced link */
reg |= E1000_PCS_LCTL_FSD; /* Force Speed */
+ /* Force flow control for forced link */
+ reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+
hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg);
}
wr32(E1000_PCS_LCTL, reg);
- if (!igb_sgmii_active_82575(hw))
+ if (!pcs_autoneg && !igb_sgmii_active_82575(hw))
igb_force_mac_fc(hw);
return ret_val;
diff --git a/drivers/net/ethernet/intel/igb/e1000_defines.h b/drivers/net/ethernet/intel/igb/e1000_defines.h
index 198d14848820..45dce06eff26 100644
--- a/drivers/net/ethernet/intel/igb/e1000_defines.h
+++ b/drivers/net/ethernet/intel/igb/e1000_defines.h
@@ -431,6 +431,10 @@
#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
#define FLOW_CONTROL_TYPE 0x8808
+/* Transmit Config Word */
+#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
+#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
+
/* 802.1q VLAN Packet Size */
#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */
#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
@@ -539,6 +543,9 @@
/* mPHY Near End Digital Loopback Override Bit */
#define E1000_MPHY_PCS_CLK_REG_DIGINELBEN 0x10
+#define E1000_PCS_LCTL_FORCE_FCTRL 0x80
+#define E1000_PCS_LSTS_AN_COMPLETE 0x10000
+
/* PHY Control Register */
#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
diff --git a/drivers/net/ethernet/intel/igb/e1000_mac.c b/drivers/net/ethernet/intel/igb/e1000_mac.c
index 7acddfe9e6d5..101e6e4da97f 100644
--- a/drivers/net/ethernet/intel/igb/e1000_mac.c
+++ b/drivers/net/ethernet/intel/igb/e1000_mac.c
@@ -839,6 +839,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
{
struct e1000_mac_info *mac = &hw->mac;
s32 ret_val = 0;
+ u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg;
u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
u16 speed, duplex;
@@ -1040,6 +1041,129 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw)
goto out;
}
}
+ /* Check for the case where we have SerDes media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->phy.media_type == e1000_media_type_internal_serdes)
+ && mac->autoneg) {
+ /* Read the PCS_LSTS and check to see if AutoNeg
+ * has completed.
+ */
+ pcs_status_reg = rd32(E1000_PCS_LSTAT);
+
+ if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) {
+ hw_dbg("PCS Auto Neg has not completed.\n");
+ return ret_val;
+ }
+
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (PCS_ANADV) and the Auto_Negotiation Base
+ * Page Ability Register (PCS_LPAB) to determine how
+ * flow control was negotiated.
+ */
+ pcs_adv_reg = rd32(E1000_PCS_ANADV);
+ pcs_lp_ability_reg = rd32(E1000_PCS_LPAB);
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (PCS_ANADV) and two bits in the Auto Negotiation Base
+ * Page Ability Register (PCS_LPAB) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | e1000_fc_full
+ *
+ */
+ if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) {
+ /* Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise Rx
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == e1000_fc_full) {
+ hw->fc.current_mode = e1000_fc_full;
+ hw_dbg("Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ hw_dbg("Flow Control = Rx PAUSE frames only.\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ */
+ else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+ (pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_tx_pause;
+ hw_dbg("Flow Control = Tx PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ */
+ else if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+ !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ hw_dbg("Flow Control = Rx PAUSE frames only.\n");
+ } else {
+ /* Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
+ hw->fc.current_mode = e1000_fc_none;
+ hw_dbg("Flow Control = NONE.\n");
+ }
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ pcs_ctrl_reg = rd32(E1000_PCS_LCTL);
+ pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+ wr32(E1000_PCS_LCTL, pcs_ctrl_reg);
+
+ ret_val = igb_force_mac_fc(hw);
+ if (ret_val) {
+ hw_dbg("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
out:
return ret_val;
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-12 17:18:57 +0000