summaryrefslogtreecommitdiff
path: root/drivers/media/video/cx18/cx18-av-core.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/media/video/cx18/cx18-av-core.c')
-rw-r--r--drivers/media/video/cx18/cx18-av-core.c374
1 files changed, 273 insertions, 101 deletions
diff --git a/drivers/media/video/cx18/cx18-av-core.c b/drivers/media/video/cx18/cx18-av-core.c
index cf2bd888a429..536dedb23ba3 100644
--- a/drivers/media/video/cx18/cx18-av-core.c
+++ b/drivers/media/video/cx18/cx18-av-core.c
@@ -99,9 +99,39 @@ int cx18_av_and_or4(struct cx18 *cx, u16 addr, u32 and_mask,
or_value);
}
-static void cx18_av_initialize(struct cx18 *cx)
+static int cx18_av_init(struct v4l2_subdev *sd, u32 val)
{
- struct cx18_av_state *state = &cx->av_state;
+ struct cx18 *cx = v4l2_get_subdevdata(sd);
+
+ /*
+ * The crystal freq used in calculations in this driver will be
+ * 28.636360 MHz.
+ * Aim to run the PLLs' VCOs near 400 MHz to minimze errors.
+ */
+
+ /*
+ * VDCLK Integer = 0x0f, Post Divider = 0x04
+ * AIMCLK Integer = 0x0e, Post Divider = 0x16
+ */
+ cx18_av_write4(cx, CXADEC_PLL_CTRL1, 0x160e040f);
+
+ /* VDCLK Fraction = 0x2be2fe */
+ /* xtal * 0xf.15f17f0/4 = 108 MHz: 432 MHz before post divide */
+ cx18_av_write4(cx, CXADEC_VID_PLL_FRAC, 0x002be2fe);
+
+ /* AIMCLK Fraction = 0x05227ad */
+ /* xtal * 0xe.2913d68/0x16 = 48000 * 384: 406 MHz pre post-div*/
+ cx18_av_write4(cx, CXADEC_AUX_PLL_FRAC, 0x005227ad);
+
+ /* SA_MCLK_SEL=1, SA_MCLK_DIV=0x16 */
+ cx18_av_write(cx, CXADEC_I2S_MCLK, 0x56);
+ return 0;
+}
+
+static void cx18_av_initialize(struct v4l2_subdev *sd)
+{
+ struct cx18_av_state *state = to_cx18_av_state(sd);
+ struct cx18 *cx = v4l2_get_subdevdata(sd);
u32 v;
cx18_av_loadfw(cx);
@@ -150,6 +180,26 @@ static void cx18_av_initialize(struct cx18 *cx)
cx18_av_write4(cx, CXADEC_SOFT_RST_CTRL, 0x8000);
cx18_av_write4(cx, CXADEC_SOFT_RST_CTRL, 0);
+ /*
+ * Disable Video Auto-config of the Analog Front End and Video PLL.
+ *
+ * Since we only use BT.656 pixel mode, which works for both 525 and 625
+ * line systems, it's just easier for us to set registers
+ * 0x102 (CXADEC_CHIP_CTRL), 0x104-0x106 (CXADEC_AFE_CTRL),
+ * 0x108-0x109 (CXADEC_PLL_CTRL1), and 0x10c-0x10f (CXADEC_VID_PLL_FRAC)
+ * ourselves, than to run around cleaning up after the auto-config.
+ *
+ * (Note: my CX23418 chip doesn't seem to let the ACFG_DIS bit
+ * get set to 1, but OTOH, it doesn't seem to do AFE and VID PLL
+ * autoconfig either.)
+ *
+ * As a default, also turn off Dual mode for ADC2 and set ADC2 to CH3.
+ */
+ cx18_av_and_or4(cx, CXADEC_CHIP_CTRL, 0xFFFBFFFF, 0x00120000);
+
+ /* Setup the Video and and Aux/Audio PLLs */
+ cx18_av_init(sd, 0);
+
/* set video to auto-detect */
/* Clear bits 11-12 to enable slow locking mode. Set autodetect mode */
/* set the comb notch = 1 */
@@ -176,12 +226,23 @@ static void cx18_av_initialize(struct cx18 *cx)
/* EncSetSignalStd(dwDevNum, pEnc->dwSigStd); */
/* EncSetVideoInput(dwDevNum, pEnc->VidIndSelection); */
- v = cx18_av_read4(cx, CXADEC_AFE_CTRL);
- v &= 0xFFFBFFFF; /* turn OFF bit 18 for droop_comp_ch1 */
- v &= 0xFFFF7FFF; /* turn OFF bit 9 for clamp_sel_ch1 */
- v &= 0xFFFFFFFE; /* turn OFF bit 0 for 12db_ch1 */
- /* v |= 0x00000001;*/ /* turn ON bit 0 for 12db_ch1 */
- cx18_av_write4(cx, CXADEC_AFE_CTRL, v);
+ /*
+ * Analog Front End (AFE)
+ * Default to luma on ch1/ADC1, chroma on ch2/ADC2, SIF on ch3/ADC2
+ * bypass_ch[1-3] use filter
+ * droop_comp_ch[1-3] disable
+ * clamp_en_ch[1-3] disable
+ * aud_in_sel ADC2
+ * luma_in_sel ADC1
+ * chroma_in_sel ADC2
+ * clamp_sel_ch[2-3] midcode
+ * clamp_sel_ch1 video decoder
+ * vga_sel_ch3 audio decoder
+ * vga_sel_ch[1-2] video decoder
+ * half_bw_ch[1-3] disable
+ * +12db_ch[1-3] disable
+ */
+ cx18_av_and_or4(cx, CXADEC_AFE_CTRL, 0xFF000000, 0x00005D00);
/* if(dwEnable && dw3DCombAvailable) { */
/* CxDevWrReg(CXADEC_SRC_COMB_CFG, 0x7728021F); */
@@ -195,50 +256,18 @@ static void cx18_av_initialize(struct cx18 *cx)
static int cx18_av_reset(struct v4l2_subdev *sd, u32 val)
{
- struct cx18 *cx = v4l2_get_subdevdata(sd);
-
- cx18_av_initialize(cx);
- return 0;
-}
-
-static int cx18_av_init(struct v4l2_subdev *sd, u32 val)
-{
- struct cx18 *cx = v4l2_get_subdevdata(sd);
-
- /*
- * The crystal freq used in calculations in this driver will be
- * 28.636360 MHz.
- * Aim to run the PLLs' VCOs near 400 MHz to minimze errors.
- */
-
- /*
- * VDCLK Integer = 0x0f, Post Divider = 0x04
- * AIMCLK Integer = 0x0e, Post Divider = 0x16
- */
- cx18_av_write4(cx, CXADEC_PLL_CTRL1, 0x160e040f);
-
- /* VDCLK Fraction = 0x2be2fe */
- /* xtal * 0xf.15f17f0/4 = 108 MHz: 432 MHz before post divide */
- cx18_av_write4(cx, CXADEC_VID_PLL_FRAC, 0x002be2fe);
-
- /* AIMCLK Fraction = 0x05227ad */
- /* xtal * 0xe.2913d68/0x16 = 48000 * 384: 406 MHz pre post-div*/
- cx18_av_write4(cx, CXADEC_AUX_PLL_FRAC, 0x005227ad);
-
- /* SA_MCLK_SEL=1, SA_MCLK_DIV=0x16 */
- cx18_av_write(cx, CXADEC_I2S_MCLK, 0x56);
+ cx18_av_initialize(sd);
return 0;
}
static int cx18_av_load_fw(struct v4l2_subdev *sd)
{
struct cx18_av_state *state = to_cx18_av_state(sd);
- struct cx18 *cx = v4l2_get_subdevdata(sd);
if (!state->is_initialized) {
/* initialize on first use */
state->is_initialized = 1;
- cx18_av_initialize(cx);
+ cx18_av_initialize(sd);
}
return 0;
}
@@ -248,8 +277,15 @@ void cx18_av_std_setup(struct cx18 *cx)
struct cx18_av_state *state = &cx->av_state;
struct v4l2_subdev *sd = &state->sd;
v4l2_std_id std = state->std;
+
+ /*
+ * Video ADC crystal clock to pixel clock SRC decimation ratio
+ * 28.636360 MHz/13.5 Mpps * 256 = 0x21f.07b
+ */
+ const int src_decimation = 0x21f;
+
int hblank, hactive, burst, vblank, vactive, sc;
- int vblank656, src_decimation;
+ int vblank656;
int luma_lpf, uv_lpf, comb;
u32 pll_int, pll_frac, pll_post;
@@ -259,40 +295,96 @@ void cx18_av_std_setup(struct cx18 *cx)
else
cx18_av_write(cx, 0x49f, 0x14);
+ /*
+ * Note: At the end of a field, there are 3 sets of half line duration
+ * (double horizontal rate) pulses:
+ *
+ * 5 (625) or 6 (525) half-lines to blank for the vertical retrace
+ * 5 (625) or 6 (525) vertical sync pulses of half line duration
+ * 5 (625) or 6 (525) half-lines of equalization pulses
+ */
if (std & V4L2_STD_625_50) {
- /* FIXME - revisit these for Sliced VBI */
+ /*
+ * The following relationships of half line counts should hold:
+ * 625 = vblank656 + vactive
+ * 10 = vblank656 - vblank = vsync pulses + equalization pulses
+ *
+ * vblank656: half lines after line 625/mid-313 of blanked video
+ * vblank: half lines, after line 5/317, of blanked video
+ * vactive: half lines of active video +
+ * 5 half lines after the end of active video
+ *
+ * As far as I can tell:
+ * vblank656 starts counting from the falling edge of the first
+ * vsync pulse (start of line 1 or mid-313)
+ * vblank starts counting from the after the 5 vsync pulses and
+ * 5 or 4 equalization pulses (start of line 6 or 318)
+ *
+ * For 625 line systems the driver will extract VBI information
+ * from lines 6-23 and lines 318-335 (but the slicer can only
+ * handle 17 lines, not the 18 in the vblank region).
+ * In addition, we need vblank656 and vblank to be one whole
+ * line longer, to cover line 24 and 336, so the SAV/EAV RP
+ * codes get generated such that the encoder can actually
+ * extract line 23 & 335 (WSS). We'll lose 1 line in each field
+ * at the top of the screen.
+ *
+ * It appears the 5 half lines that happen after active
+ * video must be included in vactive (579 instead of 574),
+ * otherwise the colors get badly displayed in various regions
+ * of the screen. I guess the chroma comb filter gets confused
+ * without them (at least when a PVR-350 is the PAL source).
+ */
+ vblank656 = 48; /* lines 1 - 24 & 313 - 336 */
+ vblank = 38; /* lines 6 - 24 & 318 - 336 */
+ vactive = 579; /* lines 24 - 313 & 337 - 626 */
+
+ /*
+ * For a 13.5 Mpps clock and 15,625 Hz line rate, a line is
+ * is 864 pixels = 720 active + 144 blanking. ITU-R BT.601
+ * specifies 12 luma clock periods or ~ 0.9 * 13.5 Mpps after
+ * the end of active video to start a horizontal line, so that
+ * leaves 132 pixels of hblank to ignore.
+ */
hblank = 132;
hactive = 720;
- burst = 93;
- vblank = 36;
- vactive = 580;
- vblank656 = 40;
- src_decimation = 0x21f;
+ /*
+ * Burst gate delay (for 625 line systems)
+ * Hsync leading edge to color burst rise = 5.6 us
+ * Color burst width = 2.25 us
+ * Gate width = 4 pixel clocks
+ * (5.6 us + 2.25/2 us) * 13.5 Mpps + 4/2 clocks = 92.79 clocks
+ */
+ burst = 93;
luma_lpf = 2;
if (std & V4L2_STD_PAL) {
uv_lpf = 1;
comb = 0x20;
- sc = 688739;
+ /* sc = 4433618.75 * src_decimation/28636360 * 2^13 */
+ sc = 688700;
} else if (std == V4L2_STD_PAL_Nc) {
uv_lpf = 1;
comb = 0x20;
- sc = 556453;
+ /* sc = 3582056.25 * src_decimation/28636360 * 2^13 */
+ sc = 556422;
} else { /* SECAM */
uv_lpf = 0;
comb = 0;
- sc = 672351;
+ /* (fr + fb)/2 = (4406260 + 4250000)/2 = 4328130 */
+ /* sc = 4328130 * src_decimation/28636360 * 2^13 */
+ sc = 672314;
}
} else {
/*
* The following relationships of half line counts should hold:
- * 525 = vsync + vactive + vblank656
- * 12 = vblank656 - vblank
+ * 525 = prevsync + vblank656 + vactive
+ * 12 = vblank656 - vblank = vsync pulses + equalization pulses
*
- * vsync: always 6 half-lines of vsync pulses
- * vactive: half lines of active video
+ * prevsync: 6 half-lines before the vsync pulses
* vblank656: half lines, after line 3/mid-266, of blanked video
* vblank: half lines, after line 9/272, of blanked video
+ * vactive: half lines of active video
*
* As far as I can tell:
* vblank656 starts counting from the falling edge of the first
@@ -319,20 +411,30 @@ void cx18_av_std_setup(struct cx18 *cx)
luma_lpf = 1;
uv_lpf = 1;
- src_decimation = 0x21f;
+ /*
+ * Burst gate delay (for 525 line systems)
+ * Hsync leading edge to color burst rise = 5.3 us
+ * Color burst width = 2.5 us
+ * Gate width = 4 pixel clocks
+ * (5.3 us + 2.5/2 us) * 13.5 Mpps + 4/2 clocks = 90.425 clocks
+ */
if (std == V4L2_STD_PAL_60) {
- burst = 0x5b;
+ burst = 90;
luma_lpf = 2;
comb = 0x20;
- sc = 688739;
+ /* sc = 4433618.75 * src_decimation/28636360 * 2^13 */
+ sc = 688700;
} else if (std == V4L2_STD_PAL_M) {
- burst = 0x61;
+ /* The 97 needs to be verified against PAL-M timings */
+ burst = 97;
comb = 0x20;
- sc = 555452;
+ /* sc = 3575611.49 * src_decimation/28636360 * 2^13 */
+ sc = 555421;
} else {
- burst = 0x5b;
+ burst = 90;
comb = 0x66;
- sc = 556063;
+ /* sc = 3579545.45.. * src_decimation/28636360 * 2^13 */
+ sc = 556032;
}
}
@@ -344,23 +446,26 @@ void cx18_av_std_setup(struct cx18 *cx)
pll_int, pll_frac, pll_post);
if (pll_post) {
- int fin, fsc, pll;
+ int fsc, pll;
+ u64 tmp;
pll = (28636360L * ((((u64)pll_int) << 25) + pll_frac)) >> 25;
pll /= pll_post;
- CX18_DEBUG_INFO_DEV(sd, "PLL = %d.%06d MHz\n",
+ CX18_DEBUG_INFO_DEV(sd, "Video PLL = %d.%06d MHz\n",
pll / 1000000, pll % 1000000);
- CX18_DEBUG_INFO_DEV(sd, "PLL/8 = %d.%06d MHz\n",
+ CX18_DEBUG_INFO_DEV(sd, "Pixel rate = %d.%06d Mpixel/sec\n",
pll / 8000000, (pll / 8) % 1000000);
- fin = ((u64)src_decimation * pll) >> 12;
- CX18_DEBUG_INFO_DEV(sd, "ADC Sampling freq = %d.%06d MHz\n",
- fin / 1000000, fin % 1000000);
+ CX18_DEBUG_INFO_DEV(sd, "ADC XTAL/pixel clock decimation ratio "
+ "= %d.%03d\n", src_decimation / 256,
+ ((src_decimation % 256) * 1000) / 256);
- fsc = (((u64)sc) * pll) >> 24L;
+ tmp = 28636360 * (u64) sc;
+ do_div(tmp, src_decimation);
+ fsc = tmp >> 13;
CX18_DEBUG_INFO_DEV(sd,
- "Chroma sub-carrier freq = %d.%06d MHz\n",
- fsc / 1000000, fsc % 1000000);
+ "Chroma sub-carrier initial freq = %d.%06d "
+ "MHz\n", fsc / 1000000, fsc % 1000000);
CX18_DEBUG_INFO_DEV(sd, "hblank %i, hactive %i, vblank %i, "
"vactive %i, vblank656 %i, src_dec %i, "
@@ -470,16 +575,23 @@ static int set_input(struct cx18 *cx, enum cx18_av_video_input vid_input,
{
struct cx18_av_state *state = &cx->av_state;
struct v4l2_subdev *sd = &state->sd;
- u8 is_composite = (vid_input >= CX18_AV_COMPOSITE1 &&
- vid_input <= CX18_AV_COMPOSITE8);
- u8 reg;
- u8 v;
+
+ enum analog_signal_type {
+ NONE, CVBS, Y, C, SIF, Pb, Pr
+ } ch[3] = {NONE, NONE, NONE};
+
+ u8 afe_mux_cfg;
+ u8 adc2_cfg;
+ u32 afe_cfg;
+ int i;
CX18_DEBUG_INFO_DEV(sd, "decoder set video input %d, audio input %d\n",
vid_input, aud_input);
- if (is_composite) {
- reg = 0xf0 + (vid_input - CX18_AV_COMPOSITE1);
+ if (vid_input >= CX18_AV_COMPOSITE1 &&
+ vid_input <= CX18_AV_COMPOSITE8) {
+ afe_mux_cfg = 0xf0 + (vid_input - CX18_AV_COMPOSITE1);
+ ch[0] = CVBS;
} else {
int luma = vid_input & 0xf0;
int chroma = vid_input & 0xf00;
@@ -493,26 +605,45 @@ static int set_input(struct cx18 *cx, enum cx18_av_video_input vid_input,
vid_input);
return -EINVAL;
}
- reg = 0xf0 + ((luma - CX18_AV_SVIDEO_LUMA1) >> 4);
+ afe_mux_cfg = 0xf0 + ((luma - CX18_AV_SVIDEO_LUMA1) >> 4);
+ ch[0] = Y;
if (chroma >= CX18_AV_SVIDEO_CHROMA7) {
- reg &= 0x3f;
- reg |= (chroma - CX18_AV_SVIDEO_CHROMA7) >> 2;
+ afe_mux_cfg &= 0x3f;
+ afe_mux_cfg |= (chroma - CX18_AV_SVIDEO_CHROMA7) >> 2;
+ ch[2] = C;
} else {
- reg &= 0xcf;
- reg |= (chroma - CX18_AV_SVIDEO_CHROMA4) >> 4;
+ afe_mux_cfg &= 0xcf;
+ afe_mux_cfg |= (chroma - CX18_AV_SVIDEO_CHROMA4) >> 4;
+ ch[1] = C;
}
}
+ /* TODO: LeadTek WinFast DVR3100 H & WinFast PVR2100 can do Y/Pb/Pr */
switch (aud_input) {
case CX18_AV_AUDIO_SERIAL1:
case CX18_AV_AUDIO_SERIAL2:
/* do nothing, use serial audio input */
break;
- case CX18_AV_AUDIO4: reg &= ~0x30; break;
- case CX18_AV_AUDIO5: reg &= ~0x30; reg |= 0x10; break;
- case CX18_AV_AUDIO6: reg &= ~0x30; reg |= 0x20; break;
- case CX18_AV_AUDIO7: reg &= ~0xc0; break;
- case CX18_AV_AUDIO8: reg &= ~0xc0; reg |= 0x40; break;
+ case CX18_AV_AUDIO4:
+ afe_mux_cfg &= ~0x30;
+ ch[1] = SIF;
+ break;
+ case CX18_AV_AUDIO5:
+ afe_mux_cfg = (afe_mux_cfg & ~0x30) | 0x10;
+ ch[1] = SIF;
+ break;
+ case CX18_AV_AUDIO6:
+ afe_mux_cfg = (afe_mux_cfg & ~0x30) | 0x20;
+ ch[1] = SIF;
+ break;
+ case CX18_AV_AUDIO7:
+ afe_mux_cfg &= ~0xc0;
+ ch[2] = SIF;
+ break;
+ case CX18_AV_AUDIO8:
+ afe_mux_cfg = (afe_mux_cfg & ~0xc0) | 0x40;
+ ch[2] = SIF;
+ break;
default:
CX18_ERR_DEV(sd, "0x%04x is not a valid audio input!\n",
@@ -520,24 +651,65 @@ static int set_input(struct cx18 *cx, enum cx18_av_video_input vid_input,
return -EINVAL;
}
- cx18_av_write_expect(cx, 0x103, reg, reg, 0xf7);
+ /* Set up analog front end multiplexers */
+ cx18_av_write_expect(cx, 0x103, afe_mux_cfg, afe_mux_cfg, 0xf7);
/* Set INPUT_MODE to Composite (0) or S-Video (1) */
- cx18_av_and_or(cx, 0x401, ~0x6, is_composite ? 0 : 0x02);
+ cx18_av_and_or(cx, 0x401, ~0x6, ch[0] == CVBS ? 0 : 0x02);
/* Set CH_SEL_ADC2 to 1 if input comes from CH3 */
- v = cx18_av_read(cx, 0x102);
- if (reg & 0x80)
- v &= ~0x2;
+ adc2_cfg = cx18_av_read(cx, 0x102);
+ if (ch[2] == NONE)
+ adc2_cfg &= ~0x2; /* No sig on CH3, set ADC2 to CH2 for input */
else
- v |= 0x2;
+ adc2_cfg |= 0x2; /* Signal on CH3, set ADC2 to CH3 for input */
+
/* Set DUAL_MODE_ADC2 to 1 if input comes from both CH2 and CH3 */
- if ((reg & 0xc0) != 0xc0 && (reg & 0x30) != 0x30)
- v |= 0x4;
+ if (ch[1] != NONE && ch[2] != NONE)
+ adc2_cfg |= 0x4; /* Set dual mode */
else
- v &= ~0x4;
- cx18_av_write_expect(cx, 0x102, v, v, 0x17);
+ adc2_cfg &= ~0x4; /* Clear dual mode */
+ cx18_av_write_expect(cx, 0x102, adc2_cfg, adc2_cfg, 0x17);
+
+ /* Configure the analog front end */
+ afe_cfg = cx18_av_read4(cx, CXADEC_AFE_CTRL);
+ afe_cfg &= 0xff000000;
+ afe_cfg |= 0x00005000; /* CHROMA_IN, AUD_IN: ADC2; LUMA_IN: ADC1 */
+ if (ch[1] != NONE && ch[2] != NONE)
+ afe_cfg |= 0x00000030; /* half_bw_ch[2-3] since in dual mode */
+
+ for (i = 0; i < 3; i++) {
+ switch (ch[i]) {
+ default:
+ case NONE:
+ /* CLAMP_SEL = Fixed to midcode clamp level */
+ afe_cfg |= (0x00000200 << i);
+ break;
+ case CVBS:
+ case Y:
+ if (i > 0)
+ afe_cfg |= 0x00002000; /* LUMA_IN_SEL: ADC2 */
+ break;
+ case C:
+ case Pb:
+ case Pr:
+ /* CLAMP_SEL = Fixed to midcode clamp level */
+ afe_cfg |= (0x00000200 << i);
+ if (i == 0 && ch[i] == C)
+ afe_cfg &= ~0x00001000; /* CHROMA_IN_SEL ADC1 */
+ break;
+ case SIF:
+ /*
+ * VGA_GAIN_SEL = Audio Decoder
+ * CLAMP_SEL = Fixed to midcode clamp level
+ */
+ afe_cfg |= (0x00000240 << i);
+ if (i == 0)
+ afe_cfg &= ~0x00004000; /* AUD_IN_SEL ADC1 */
+ break;
+ }
+ }
- /*cx18_av_and_or4(cx, 0x104, ~0x001b4180, 0x00004180);*/
+ cx18_av_write4(cx, CXADEC_AFE_CTRL, afe_cfg);
state->vid_input = vid_input;
state->aud_input = aud_input;
@@ -858,9 +1030,9 @@ static int cx18_av_s_fmt(struct v4l2_subdev *sd, struct v4l2_format *fmt)
* cx18_av_std_setup(), above standard values:
*
* 480 + 1 for 60 Hz systems
- * 576 + 4 for 50 Hz systems
+ * 576 + 3 for 50 Hz systems
*/
- Vlines = pix->height + (is_50Hz ? 4 : 1);
+ Vlines = pix->height + (is_50Hz ? 3 : 1);
/*
* Invalid height and width scaling requests are:
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 15:23:35 +0000