diff options
Diffstat (limited to 'arch/sparc/include/asm')
| -rw-r--r-- | arch/sparc/include/asm/dma.h | 141 | ||||
| -rw-r--r-- | arch/sparc/include/asm/dma_32.h | 288 | ||||
| -rw-r--r-- | arch/sparc/include/asm/dma_64.h | 205 | ||||
| -rw-r--r-- | arch/sparc/include/asm/floppy_32.h | 11 |
4 files changed, 147 insertions, 498 deletions
diff --git a/arch/sparc/include/asm/dma.h b/arch/sparc/include/asm/dma.h index aa1d90ac04c5..493563446790 100644 --- a/arch/sparc/include/asm/dma.h +++ b/arch/sparc/include/asm/dma.h @@ -1,8 +1,139 @@ -#ifndef ___ASM_SPARC_DMA_H -#define ___ASM_SPARC_DMA_H -#if defined(__sparc__) && defined(__arch64__) -#include <asm/dma_64.h> +#ifndef _ASM_SPARC_DMA_H +#define _ASM_SPARC_DMA_H + +/* These are irrelevant for Sparc DMA, but we leave it in so that + * things can compile. + */ +#define MAX_DMA_CHANNELS 8 +#define DMA_MODE_READ 1 +#define DMA_MODE_WRITE 2 +#define MAX_DMA_ADDRESS (~0UL) + +/* Useful constants */ +#define SIZE_16MB (16*1024*1024) +#define SIZE_64K (64*1024) + +/* SBUS DMA controller reg offsets */ +#define DMA_CSR 0x00UL /* rw DMA control/status register 0x00 */ +#define DMA_ADDR 0x04UL /* rw DMA transfer address register 0x04 */ +#define DMA_COUNT 0x08UL /* rw DMA transfer count register 0x08 */ +#define DMA_TEST 0x0cUL /* rw DMA test/debug register 0x0c */ + +/* Fields in the cond_reg register */ +/* First, the version identification bits */ +#define DMA_DEVICE_ID 0xf0000000 /* Device identification bits */ +#define DMA_VERS0 0x00000000 /* Sunray DMA version */ +#define DMA_ESCV1 0x40000000 /* DMA ESC Version 1 */ +#define DMA_VERS1 0x80000000 /* DMA rev 1 */ +#define DMA_VERS2 0xa0000000 /* DMA rev 2 */ +#define DMA_VERHME 0xb0000000 /* DMA hme gate array */ +#define DMA_VERSPLUS 0x90000000 /* DMA rev 1 PLUS */ + +#define DMA_HNDL_INTR 0x00000001 /* An IRQ needs to be handled */ +#define DMA_HNDL_ERROR 0x00000002 /* We need to take an error */ +#define DMA_FIFO_ISDRAIN 0x0000000c /* The DMA FIFO is draining */ +#define DMA_INT_ENAB 0x00000010 /* Turn on interrupts */ +#define DMA_FIFO_INV 0x00000020 /* Invalidate the FIFO */ +#define DMA_ACC_SZ_ERR 0x00000040 /* The access size was bad */ +#define DMA_FIFO_STDRAIN 0x00000040 /* DMA_VERS1 Drain the FIFO */ +#define DMA_RST_SCSI 0x00000080 /* Reset the SCSI controller */ +#define DMA_RST_ENET DMA_RST_SCSI /* Reset the ENET controller */ +#define DMA_ST_WRITE 0x00000100 /* write from device to memory */ +#define DMA_ENABLE 0x00000200 /* Fire up DMA, handle requests */ +#define DMA_PEND_READ 0x00000400 /* DMA_VERS1/0/PLUS Pending Read */ +#define DMA_ESC_BURST 0x00000800 /* 1=16byte 0=32byte */ +#define DMA_READ_AHEAD 0x00001800 /* DMA read ahead partial longword */ +#define DMA_DSBL_RD_DRN 0x00001000 /* No EC drain on slave reads */ +#define DMA_BCNT_ENAB 0x00002000 /* If on, use the byte counter */ +#define DMA_TERM_CNTR 0x00004000 /* Terminal counter */ +#define DMA_SCSI_SBUS64 0x00008000 /* HME: Enable 64-bit SBUS mode. */ +#define DMA_CSR_DISAB 0x00010000 /* No FIFO drains during csr */ +#define DMA_SCSI_DISAB 0x00020000 /* No FIFO drains during reg */ +#define DMA_DSBL_WR_INV 0x00020000 /* No EC inval. on slave writes */ +#define DMA_ADD_ENABLE 0x00040000 /* Special ESC DVMA optimization */ +#define DMA_E_BURSTS 0x000c0000 /* ENET: SBUS r/w burst mask */ +#define DMA_E_BURST32 0x00040000 /* ENET: SBUS 32 byte r/w burst */ +#define DMA_E_BURST16 0x00000000 /* ENET: SBUS 16 byte r/w burst */ +#define DMA_BRST_SZ 0x000c0000 /* SCSI: SBUS r/w burst size */ +#define DMA_BRST64 0x000c0000 /* SCSI: 64byte bursts (HME on UltraSparc only) */ +#define DMA_BRST32 0x00040000 /* SCSI: 32byte bursts */ +#define DMA_BRST16 0x00000000 /* SCSI: 16byte bursts */ +#define DMA_BRST0 0x00080000 /* SCSI: no bursts (non-HME gate arrays) */ +#define DMA_ADDR_DISAB 0x00100000 /* No FIFO drains during addr */ +#define DMA_2CLKS 0x00200000 /* Each transfer = 2 clock ticks */ +#define DMA_3CLKS 0x00400000 /* Each transfer = 3 clock ticks */ +#define DMA_EN_ENETAUI DMA_3CLKS /* Put lance into AUI-cable mode */ +#define DMA_CNTR_DISAB 0x00800000 /* No IRQ when DMA_TERM_CNTR set */ +#define DMA_AUTO_NADDR 0x01000000 /* Use "auto nxt addr" feature */ +#define DMA_SCSI_ON 0x02000000 /* Enable SCSI dma */ +#define DMA_PARITY_OFF 0x02000000 /* HME: disable parity checking */ +#define DMA_LOADED_ADDR 0x04000000 /* Address has been loaded */ +#define DMA_LOADED_NADDR 0x08000000 /* Next address has been loaded */ +#define DMA_RESET_FAS366 0x08000000 /* HME: Assert RESET to FAS366 */ + +/* Values describing the burst-size property from the PROM */ +#define DMA_BURST1 0x01 +#define DMA_BURST2 0x02 +#define DMA_BURST4 0x04 +#define DMA_BURST8 0x08 +#define DMA_BURST16 0x10 +#define DMA_BURST32 0x20 +#define DMA_BURST64 0x40 +#define DMA_BURSTBITS 0x7f + +/* From PCI */ + +#ifdef CONFIG_PCI +extern int isa_dma_bridge_buggy; #else -#include <asm/dma_32.h> +#define isa_dma_bridge_buggy (0) #endif + +#ifdef CONFIG_SPARC32 + +#include <asm/sbus.h> + +/* Routines for data transfer buffers. */ +BTFIXUPDEF_CALL(char *, mmu_lockarea, char *, unsigned long) +BTFIXUPDEF_CALL(void, mmu_unlockarea, char *, unsigned long) + +#define mmu_lockarea(vaddr,len) BTFIXUP_CALL(mmu_lockarea)(vaddr,len) +#define mmu_unlockarea(vaddr,len) BTFIXUP_CALL(mmu_unlockarea)(vaddr,len) + +/* These are implementations for sbus_map_sg/sbus_unmap_sg... collapse later */ +BTFIXUPDEF_CALL(__u32, mmu_get_scsi_one, char *, unsigned long, struct sbus_bus *sbus) +BTFIXUPDEF_CALL(void, mmu_get_scsi_sgl, struct scatterlist *, int, struct sbus_bus *sbus) +BTFIXUPDEF_CALL(void, mmu_release_scsi_one, __u32, unsigned long, struct sbus_bus *sbus) +BTFIXUPDEF_CALL(void, mmu_release_scsi_sgl, struct scatterlist *, int, struct sbus_bus *sbus) + +#define mmu_get_scsi_one(vaddr,len,sbus) BTFIXUP_CALL(mmu_get_scsi_one)(vaddr,len,sbus) +#define mmu_get_scsi_sgl(sg,sz,sbus) BTFIXUP_CALL(mmu_get_scsi_sgl)(sg,sz,sbus) +#define mmu_release_scsi_one(vaddr,len,sbus) BTFIXUP_CALL(mmu_release_scsi_one)(vaddr,len,sbus) +#define mmu_release_scsi_sgl(sg,sz,sbus) BTFIXUP_CALL(mmu_release_scsi_sgl)(sg,sz,sbus) + +/* + * mmu_map/unmap are provided by iommu/iounit; Invalid to call on IIep. + * + * The mmu_map_dma_area establishes two mappings in one go. + * These mappings point to pages normally mapped at 'va' (linear address). + * First mapping is for CPU visible address at 'a', uncached. + * This is an alias, but it works because it is an uncached mapping. + * Second mapping is for device visible address, or "bus" address. + * The bus address is returned at '*pba'. + * + * These functions seem distinct, but are hard to split. On sun4c, + * at least for now, 'a' is equal to bus address, and retured in *pba. + * On sun4m, page attributes depend on the CPU type, so we have to + * know if we are mapping RAM or I/O, so it has to be an additional argument + * to a separate mapping function for CPU visible mappings. + */ +BTFIXUPDEF_CALL(int, mmu_map_dma_area, dma_addr_t *, unsigned long, unsigned long, int len) +BTFIXUPDEF_CALL(struct page *, mmu_translate_dvma, unsigned long busa) +BTFIXUPDEF_CALL(void, mmu_unmap_dma_area, unsigned long busa, int len) + +#define mmu_map_dma_area(pba,va,a,len) BTFIXUP_CALL(mmu_map_dma_area)(pba,va,a,len) +#define mmu_unmap_dma_area(ba,len) BTFIXUP_CALL(mmu_unmap_dma_area)(ba,len) +#define mmu_translate_dvma(ba) BTFIXUP_CALL(mmu_translate_dvma)(ba) #endif + +#endif /* !(_ASM_SPARC_DMA_H) */ diff --git a/arch/sparc/include/asm/dma_32.h b/arch/sparc/include/asm/dma_32.h deleted file mode 100644 index cf7189c0079b..000000000000 --- a/arch/sparc/include/asm/dma_32.h +++ /dev/null @@ -1,288 +0,0 @@ -/* include/asm/dma.h - * - * Copyright 1995 (C) David S. Miller (davem@davemloft.net) - */ - -#ifndef _ASM_SPARC_DMA_H -#define _ASM_SPARC_DMA_H - -#include <linux/kernel.h> -#include <linux/types.h> - -#include <asm/vac-ops.h> /* for invalidate's, etc. */ -#include <asm/sbus.h> -#include <asm/delay.h> -#include <asm/oplib.h> -#include <asm/system.h> -#include <asm/io.h> -#include <linux/spinlock.h> - -struct page; -extern spinlock_t dma_spin_lock; - -static inline unsigned long claim_dma_lock(void) -{ - unsigned long flags; - spin_lock_irqsave(&dma_spin_lock, flags); - return flags; -} - -static inline void release_dma_lock(unsigned long flags) -{ - spin_unlock_irqrestore(&dma_spin_lock, flags); -} - -/* These are irrelevant for Sparc DMA, but we leave it in so that - * things can compile. - */ -#define MAX_DMA_CHANNELS 8 -#define MAX_DMA_ADDRESS (~0UL) -#define DMA_MODE_READ 1 -#define DMA_MODE_WRITE 2 - -/* Useful constants */ -#define SIZE_16MB (16*1024*1024) -#define SIZE_64K (64*1024) - -/* SBUS DMA controller reg offsets */ -#define DMA_CSR 0x00UL /* rw DMA control/status register 0x00 */ -#define DMA_ADDR 0x04UL /* rw DMA transfer address register 0x04 */ -#define DMA_COUNT 0x08UL /* rw DMA transfer count register 0x08 */ -#define DMA_TEST 0x0cUL /* rw DMA test/debug register 0x0c */ - -/* DVMA chip revisions */ -enum dvma_rev { - dvmarev0, - dvmaesc1, - dvmarev1, - dvmarev2, - dvmarev3, - dvmarevplus, - dvmahme -}; - -#define DMA_HASCOUNT(rev) ((rev)==dvmaesc1) - -/* Linux DMA information structure, filled during probe. */ -struct sbus_dma { - struct sbus_dma *next; - struct sbus_dev *sdev; - void __iomem *regs; - - /* Status, misc info */ - int node; /* Prom node for this DMA device */ - int running; /* Are we doing DMA now? */ - int allocated; /* Are we "owned" by anyone yet? */ - - /* Transfer information. */ - unsigned long addr; /* Start address of current transfer */ - int nbytes; /* Size of current transfer */ - int realbytes; /* For splitting up large transfers, etc. */ - - /* DMA revision */ - enum dvma_rev revision; -}; - -extern struct sbus_dma *dma_chain; - -/* Broken hardware... */ -#ifdef CONFIG_SUN4 -/* Have to sort this out. Does rev0 work fine on sun4[cmd] without isbroken? - * Or is rev0 present only on sun4 boxes? -jj */ -#define DMA_ISBROKEN(dma) ((dma)->revision == dvmarev0 || (dma)->revision == dvmarev1) -#else -#define DMA_ISBROKEN(dma) ((dma)->revision == dvmarev1) -#endif -#define DMA_ISESC1(dma) ((dma)->revision == dvmaesc1) - -/* Main routines in dma.c */ -extern void dvma_init(struct sbus_bus *); - -/* Fields in the cond_reg register */ -/* First, the version identification bits */ -#define DMA_DEVICE_ID 0xf0000000 /* Device identification bits */ -#define DMA_VERS0 0x00000000 /* Sunray DMA version */ -#define DMA_ESCV1 0x40000000 /* DMA ESC Version 1 */ -#define DMA_VERS1 0x80000000 /* DMA rev 1 */ -#define DMA_VERS2 0xa0000000 /* DMA rev 2 */ -#define DMA_VERHME 0xb0000000 /* DMA hme gate array */ -#define DMA_VERSPLUS 0x90000000 /* DMA rev 1 PLUS */ - -#define DMA_HNDL_INTR 0x00000001 /* An IRQ needs to be handled */ -#define DMA_HNDL_ERROR 0x00000002 /* We need to take an error */ -#define DMA_FIFO_ISDRAIN 0x0000000c /* The DMA FIFO is draining */ -#define DMA_INT_ENAB 0x00000010 /* Turn on interrupts */ -#define DMA_FIFO_INV 0x00000020 /* Invalidate the FIFO */ -#define DMA_ACC_SZ_ERR 0x00000040 /* The access size was bad */ -#define DMA_FIFO_STDRAIN 0x00000040 /* DMA_VERS1 Drain the FIFO */ -#define DMA_RST_SCSI 0x00000080 /* Reset the SCSI controller */ -#define DMA_RST_ENET DMA_RST_SCSI /* Reset the ENET controller */ -#define DMA_RST_BPP DMA_RST_SCSI /* Reset the BPP controller */ -#define DMA_ST_WRITE 0x00000100 /* write from device to memory */ -#define DMA_ENABLE 0x00000200 /* Fire up DMA, handle requests */ -#define DMA_PEND_READ 0x00000400 /* DMA_VERS1/0/PLUS Pending Read */ -#define DMA_ESC_BURST 0x00000800 /* 1=16byte 0=32byte */ -#define DMA_READ_AHEAD 0x00001800 /* DMA read ahead partial longword */ -#define DMA_DSBL_RD_DRN 0x00001000 /* No EC drain on slave reads */ -#define DMA_BCNT_ENAB 0x00002000 /* If on, use the byte counter */ -#define DMA_TERM_CNTR 0x00004000 /* Terminal counter */ -#define DMA_SCSI_SBUS64 0x00008000 /* HME: Enable 64-bit SBUS mode. */ -#define DMA_CSR_DISAB 0x00010000 /* No FIFO drains during csr */ -#define DMA_SCSI_DISAB 0x00020000 /* No FIFO drains during reg */ -#define DMA_DSBL_WR_INV 0x00020000 /* No EC inval. on slave writes */ -#define DMA_ADD_ENABLE 0x00040000 /* Special ESC DVMA optimization */ -#define DMA_E_BURSTS 0x000c0000 /* ENET: SBUS r/w burst mask */ -#define DMA_E_BURST32 0x00040000 /* ENET: SBUS 32 byte r/w burst */ -#define DMA_E_BURST16 0x00000000 /* ENET: SBUS 16 byte r/w burst */ -#define DMA_BRST_SZ 0x000c0000 /* SCSI: SBUS r/w burst size */ -#define DMA_BRST64 0x00080000 /* SCSI: 64byte bursts (HME on UltraSparc only) */ -#define DMA_BRST32 0x00040000 /* SCSI/BPP: 32byte bursts */ -#define DMA_BRST16 0x00000000 /* SCSI/BPP: 16byte bursts */ -#define DMA_BRST0 0x00080000 /* SCSI: no bursts (non-HME gate arrays) */ -#define DMA_ADDR_DISAB 0x00100000 /* No FIFO drains during addr */ -#define DMA_2CLKS 0x00200000 /* Each transfer = 2 clock ticks */ -#define DMA_3CLKS 0x00400000 /* Each transfer = 3 clock ticks */ -#define DMA_EN_ENETAUI DMA_3CLKS /* Put lance into AUI-cable mode */ -#define DMA_CNTR_DISAB 0x00800000 /* No IRQ when DMA_TERM_CNTR set */ -#define DMA_AUTO_NADDR 0x01000000 /* Use "auto nxt addr" feature */ -#define DMA_SCSI_ON 0x02000000 /* Enable SCSI dma */ -#define DMA_BPP_ON DMA_SCSI_ON /* Enable BPP dma */ -#define DMA_PARITY_OFF 0x02000000 /* HME: disable parity checking */ -#define DMA_LOADED_ADDR 0x04000000 /* Address has been loaded */ -#define DMA_LOADED_NADDR 0x08000000 /* Next address has been loaded */ -#define DMA_RESET_FAS366 0x08000000 /* HME: Assert RESET to FAS366 */ - -/* Values describing the burst-size property from the PROM */ -#define DMA_BURST1 0x01 -#define DMA_BURST2 0x02 -#define DMA_BURST4 0x04 -#define DMA_BURST8 0x08 -#define DMA_BURST16 0x10 -#define DMA_BURST32 0x20 -#define DMA_BURST64 0x40 -#define DMA_BURSTBITS 0x7f - -/* Determine highest possible final transfer address given a base */ -#define DMA_MAXEND(addr) (0x01000000UL-(((unsigned long)(addr))&0x00ffffffUL)) - -/* Yes, I hack a lot of elisp in my spare time... */ -#define DMA_ERROR_P(regs) ((((regs)->cond_reg) & DMA_HNDL_ERROR)) -#define DMA_IRQ_P(regs) ((((regs)->cond_reg) & (DMA_HNDL_INTR | DMA_HNDL_ERROR))) -#define DMA_WRITE_P(regs) ((((regs)->cond_reg) & DMA_ST_WRITE)) -#define DMA_OFF(regs) ((((regs)->cond_reg) &= (~DMA_ENABLE))) -#define DMA_INTSOFF(regs) ((((regs)->cond_reg) &= (~DMA_INT_ENAB))) -#define DMA_INTSON(regs) ((((regs)->cond_reg) |= (DMA_INT_ENAB))) -#define DMA_PUNTFIFO(regs) ((((regs)->cond_reg) |= DMA_FIFO_INV)) -#define DMA_SETSTART(regs, addr) ((((regs)->st_addr) = (char *) addr)) -#define DMA_BEGINDMA_W(regs) \ - ((((regs)->cond_reg |= (DMA_ST_WRITE|DMA_ENABLE|DMA_INT_ENAB)))) -#define DMA_BEGINDMA_R(regs) \ - ((((regs)->cond_reg |= ((DMA_ENABLE|DMA_INT_ENAB)&(~DMA_ST_WRITE))))) - -/* For certain DMA chips, we need to disable ints upon irq entry - * and turn them back on when we are done. So in any ESP interrupt - * handler you *must* call DMA_IRQ_ENTRY upon entry and DMA_IRQ_EXIT - * when leaving the handler. You have been warned... - */ -#define DMA_IRQ_ENTRY(dma, dregs) do { \ - if(DMA_ISBROKEN(dma)) DMA_INTSOFF(dregs); \ - } while (0) - -#define DMA_IRQ_EXIT(dma, dregs) do { \ - if(DMA_ISBROKEN(dma)) DMA_INTSON(dregs); \ - } while(0) - -#if 0 /* P3 this stuff is inline in ledma.c:init_restart_ledma() */ -/* Pause until counter runs out or BIT isn't set in the DMA condition - * register. - */ -static inline void sparc_dma_pause(struct sparc_dma_registers *regs, - unsigned long bit) -{ - int ctr = 50000; /* Let's find some bugs ;) */ - - /* Busy wait until the bit is not set any more */ - while((regs->cond_reg&bit) && (ctr>0)) { - ctr--; - __delay(5); - } - - /* Check for bogus outcome. */ - if(!ctr) - panic("DMA timeout"); -} - -/* Reset the friggin' thing... */ -#define DMA_RESET(dma) do { \ - struct sparc_dma_registers *regs = dma->regs; \ - /* Let the current FIFO drain itself */ \ - sparc_dma_pause(regs, (DMA_FIFO_ISDRAIN)); \ - /* Reset the logic */ \ - regs->cond_reg |= (DMA_RST_SCSI); /* assert */ \ - __delay(400); /* let the bits set ;) */ \ - regs->cond_reg &= ~(DMA_RST_SCSI); /* de-assert */ \ - sparc_dma_enable_interrupts(regs); /* Re-enable interrupts */ \ - /* Enable FAST transfers if available */ \ - if(dma->revision>dvmarev1) regs->cond_reg |= DMA_3CLKS; \ - dma->running = 0; \ -} while(0) -#endif - -#define for_each_dvma(dma) \ - for((dma) = dma_chain; (dma); (dma) = (dma)->next) - -extern int get_dma_list(char *); -extern int request_dma(unsigned int, __const__ char *); -extern void free_dma(unsigned int); - -/* From PCI */ - -#ifdef CONFIG_PCI -extern int isa_dma_bridge_buggy; -#else -#define isa_dma_bridge_buggy (0) -#endif - -/* Routines for data transfer buffers. */ -BTFIXUPDEF_CALL(char *, mmu_lockarea, char *, unsigned long) -BTFIXUPDEF_CALL(void, mmu_unlockarea, char *, unsigned long) - -#define mmu_lockarea(vaddr,len) BTFIXUP_CALL(mmu_lockarea)(vaddr,len) -#define mmu_unlockarea(vaddr,len) BTFIXUP_CALL(mmu_unlockarea)(vaddr,len) - -/* These are implementations for sbus_map_sg/sbus_unmap_sg... collapse later */ -BTFIXUPDEF_CALL(__u32, mmu_get_scsi_one, char *, unsigned long, struct sbus_bus *sbus) -BTFIXUPDEF_CALL(void, mmu_get_scsi_sgl, struct scatterlist *, int, struct sbus_bus *sbus) -BTFIXUPDEF_CALL(void, mmu_release_scsi_one, __u32, unsigned long, struct sbus_bus *sbus) -BTFIXUPDEF_CALL(void, mmu_release_scsi_sgl, struct scatterlist *, int, struct sbus_bus *sbus) - -#define mmu_get_scsi_one(vaddr,len,sbus) BTFIXUP_CALL(mmu_get_scsi_one)(vaddr,len,sbus) -#define mmu_get_scsi_sgl(sg,sz,sbus) BTFIXUP_CALL(mmu_get_scsi_sgl)(sg,sz,sbus) -#define mmu_release_scsi_one(vaddr,len,sbus) BTFIXUP_CALL(mmu_release_scsi_one)(vaddr,len,sbus) -#define mmu_release_scsi_sgl(sg,sz,sbus) BTFIXUP_CALL(mmu_release_scsi_sgl)(sg,sz,sbus) - -/* - * mmu_map/unmap are provided by iommu/iounit; Invalid to call on IIep. - * - * The mmu_map_dma_area establishes two mappings in one go. - * These mappings point to pages normally mapped at 'va' (linear address). - * First mapping is for CPU visible address at 'a', uncached. - * This is an alias, but it works because it is an uncached mapping. - * Second mapping is for device visible address, or "bus" address. - * The bus address is returned at '*pba'. - * - * These functions seem distinct, but are hard to split. On sun4c, - * at least for now, 'a' is equal to bus address, and retured in *pba. - * On sun4m, page attributes depend on the CPU type, so we have to - * know if we are mapping RAM or I/O, so it has to be an additional argument - * to a separate mapping function for CPU visible mappings. - */ -BTFIXUPDEF_CALL(int, mmu_map_dma_area, dma_addr_t *, unsigned long, unsigned long, int len) -BTFIXUPDEF_CALL(struct page *, mmu_translate_dvma, unsigned long busa) -BTFIXUPDEF_CALL(void, mmu_unmap_dma_area, unsigned long busa, int len) - -#define mmu_map_dma_area(pba,va,a,len) BTFIXUP_CALL(mmu_map_dma_area)(pba,va,a,len) -#define mmu_unmap_dma_area(ba,len) BTFIXUP_CALL(mmu_unmap_dma_area)(ba,len) -#define mmu_translate_dvma(ba) BTFIXUP_CALL(mmu_translate_dvma)(ba) - -#endif /* !(_ASM_SPARC_DMA_H) */ diff --git a/arch/sparc/include/asm/dma_64.h b/arch/sparc/include/asm/dma_64.h deleted file mode 100644 index 46a8aecffc02..000000000000 --- a/arch/sparc/include/asm/dma_64.h +++ /dev/null @@ -1,205 +0,0 @@ -/* - * include/asm/dma.h - * - * Copyright 1996 (C) David S. Miller (davem@caip.rutgers.edu) - */ - -#ifndef _ASM_SPARC64_DMA_H -#define _ASM_SPARC64_DMA_H - -#include <linux/kernel.h> -#include <linux/types.h> -#include <linux/spinlock.h> - -#include <asm/sbus.h> -#include <asm/delay.h> -#include <asm/oplib.h> - -/* These are irrelevant for Sparc DMA, but we leave it in so that - * things can compile. - */ -#define MAX_DMA_CHANNELS 8 -#define DMA_MODE_READ 1 -#define DMA_MODE_WRITE 2 -#define MAX_DMA_ADDRESS (~0UL) - -/* Useful constants */ -#define SIZE_16MB (16*1024*1024) -#define SIZE_64K (64*1024) - -/* SBUS DMA controller reg offsets */ -#define DMA_CSR 0x00UL /* rw DMA control/status register 0x00 */ -#define DMA_ADDR 0x04UL /* rw DMA transfer address register 0x04 */ -#define DMA_COUNT 0x08UL /* rw DMA transfer count register 0x08 */ -#define DMA_TEST 0x0cUL /* rw DMA test/debug register 0x0c */ - -/* DVMA chip revisions */ -enum dvma_rev { - dvmarev0, - dvmaesc1, - dvmarev1, - dvmarev2, - dvmarev3, - dvmarevplus, - dvmahme -}; - -#define DMA_HASCOUNT(rev) ((rev)==dvmaesc1) - -/* Linux DMA information structure, filled during probe. */ -struct sbus_dma { - struct sbus_dma *next; - struct sbus_dev *sdev; - void __iomem *regs; - - /* Status, misc info */ - int node; /* Prom node for this DMA device */ - int running; /* Are we doing DMA now? */ - int allocated; /* Are we "owned" by anyone yet? */ - - /* Transfer information. */ - u32 addr; /* Start address of current transfer */ - int nbytes; /* Size of current transfer */ - int realbytes; /* For splitting up large transfers, etc. */ - - /* DMA revision */ - enum dvma_rev revision; -}; - -extern struct sbus_dma *dma_chain; - -/* Broken hardware... */ -#define DMA_ISBROKEN(dma) ((dma)->revision == dvmarev1) -#define DMA_ISESC1(dma) ((dma)->revision == dvmaesc1) - -/* Main routines in dma.c */ -extern void dvma_init(struct sbus_bus *); - -/* Fields in the cond_reg register */ -/* First, the version identification bits */ -#define DMA_DEVICE_ID 0xf0000000 /* Device identification bits */ -#define DMA_VERS0 0x00000000 /* Sunray DMA version */ -#define DMA_ESCV1 0x40000000 /* DMA ESC Version 1 */ -#define DMA_VERS1 0x80000000 /* DMA rev 1 */ -#define DMA_VERS2 0xa0000000 /* DMA rev 2 */ -#define DMA_VERHME 0xb0000000 /* DMA hme gate array */ -#define DMA_VERSPLUS 0x90000000 /* DMA rev 1 PLUS */ - -#define DMA_HNDL_INTR 0x00000001 /* An IRQ needs to be handled */ -#define DMA_HNDL_ERROR 0x00000002 /* We need to take an error */ -#define DMA_FIFO_ISDRAIN 0x0000000c /* The DMA FIFO is draining */ -#define DMA_INT_ENAB 0x00000010 /* Turn on interrupts */ -#define DMA_FIFO_INV 0x00000020 /* Invalidate the FIFO */ -#define DMA_ACC_SZ_ERR 0x00000040 /* The access size was bad */ -#define DMA_FIFO_STDRAIN 0x00000040 /* DMA_VERS1 Drain the FIFO */ -#define DMA_RST_SCSI 0x00000080 /* Reset the SCSI controller */ -#define DMA_RST_ENET DMA_RST_SCSI /* Reset the ENET controller */ -#define DMA_ST_WRITE 0x00000100 /* write from device to memory */ -#define DMA_ENABLE 0x00000200 /* Fire up DMA, handle requests */ -#define DMA_PEND_READ 0x00000400 /* DMA_VERS1/0/PLUS Pending Read */ -#define DMA_ESC_BURST 0x00000800 /* 1=16byte 0=32byte */ -#define DMA_READ_AHEAD 0x00001800 /* DMA read ahead partial longword */ -#define DMA_DSBL_RD_DRN 0x00001000 /* No EC drain on slave reads */ -#define DMA_BCNT_ENAB 0x00002000 /* If on, use the byte counter */ -#define DMA_TERM_CNTR 0x00004000 /* Terminal counter */ -#define DMA_SCSI_SBUS64 0x00008000 /* HME: Enable 64-bit SBUS mode. */ -#define DMA_CSR_DISAB 0x00010000 /* No FIFO drains during csr */ -#define DMA_SCSI_DISAB 0x00020000 /* No FIFO drains during reg */ -#define DMA_DSBL_WR_INV 0x00020000 /* No EC inval. on slave writes */ -#define DMA_ADD_ENABLE 0x00040000 /* Special ESC DVMA optimization */ -#define DMA_E_BURSTS 0x000c0000 /* ENET: SBUS r/w burst mask */ -#define DMA_E_BURST32 0x00040000 /* ENET: SBUS 32 byte r/w burst */ -#define DMA_E_BURST16 0x00000000 /* ENET: SBUS 16 byte r/w burst */ -#define DMA_BRST_SZ 0x000c0000 /* SCSI: SBUS r/w burst size */ -#define DMA_BRST64 0x000c0000 /* SCSI: 64byte bursts (HME on UltraSparc only) */ -#define DMA_BRST32 0x00040000 /* SCSI: 32byte bursts */ -#define DMA_BRST16 0x00000000 /* SCSI: 16byte bursts */ -#define DMA_BRST0 0x00080000 /* SCSI: no bursts (non-HME gate arrays) */ -#define DMA_ADDR_DISAB 0x00100000 /* No FIFO drains during addr */ -#define DMA_2CLKS 0x00200000 /* Each transfer = 2 clock ticks */ -#define DMA_3CLKS 0x00400000 /* Each transfer = 3 clock ticks */ -#define DMA_EN_ENETAUI DMA_3CLKS /* Put lance into AUI-cable mode */ -#define DMA_CNTR_DISAB 0x00800000 /* No IRQ when DMA_TERM_CNTR set */ -#define DMA_AUTO_NADDR 0x01000000 /* Use "auto nxt addr" feature */ -#define DMA_SCSI_ON 0x02000000 /* Enable SCSI dma */ -#define DMA_PARITY_OFF 0x02000000 /* HME: disable parity checking */ -#define DMA_LOADED_ADDR 0x04000000 /* Address has been loaded */ -#define DMA_LOADED_NADDR 0x08000000 /* Next address has been loaded */ -#define DMA_RESET_FAS366 0x08000000 /* HME: Assert RESET to FAS366 */ - -/* Values describing the burst-size property from the PROM */ -#define DMA_BURST1 0x01 -#define DMA_BURST2 0x02 -#define DMA_BURST4 0x04 -#define DMA_BURST8 0x08 -#define DMA_BURST16 0x10 -#define DMA_BURST32 0x20 -#define DMA_BURST64 0x40 -#define DMA_BURSTBITS 0x7f - -/* Determine highest possible final transfer address given a base */ -#define DMA_MAXEND(addr) (0x01000000UL-(((unsigned long)(addr))&0x00ffffffUL)) - -/* Yes, I hack a lot of elisp in my spare time... */ -#define DMA_ERROR_P(regs) ((sbus_readl((regs) + DMA_CSR) & DMA_HNDL_ERROR)) -#define DMA_IRQ_P(regs) ((sbus_readl((regs) + DMA_CSR)) & (DMA_HNDL_INTR | DMA_HNDL_ERROR)) -#define DMA_WRITE_P(regs) ((sbus_readl((regs) + DMA_CSR) & DMA_ST_WRITE)) -#define DMA_OFF(__regs) \ -do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \ - tmp &= ~DMA_ENABLE; \ - sbus_writel(tmp, (__regs) + DMA_CSR); \ -} while(0) -#define DMA_INTSOFF(__regs) \ -do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \ - tmp &= ~DMA_INT_ENAB; \ - sbus_writel(tmp, (__regs) + DMA_CSR); \ -} while(0) -#define DMA_INTSON(__regs) \ -do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \ - tmp |= DMA_INT_ENAB; \ - sbus_writel(tmp, (__regs) + DMA_CSR); \ -} while(0) -#define DMA_PUNTFIFO(__regs) \ -do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \ - tmp |= DMA_FIFO_INV; \ - sbus_writel(tmp, (__regs) + DMA_CSR); \ -} while(0) -#define DMA_SETSTART(__regs, __addr) \ - sbus_writel((u32)(__addr), (__regs) + DMA_ADDR); -#define DMA_BEGINDMA_W(__regs) \ -do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \ - tmp |= (DMA_ST_WRITE|DMA_ENABLE|DMA_INT_ENAB); \ - sbus_writel(tmp, (__regs) + DMA_CSR); \ -} while(0) -#define DMA_BEGINDMA_R(__regs) \ -do { u32 tmp = sbus_readl((__regs) + DMA_CSR); \ - tmp |= (DMA_ENABLE|DMA_INT_ENAB); \ - tmp &= ~DMA_ST_WRITE; \ - sbus_writel(tmp, (__regs) + DMA_CSR); \ -} while(0) - -/* For certain DMA chips, we need to disable ints upon irq entry - * and turn them back on when we are done. So in any ESP interrupt - * handler you *must* call DMA_IRQ_ENTRY upon entry and DMA_IRQ_EXIT - * when leaving the handler. You have been warned... - */ -#define DMA_IRQ_ENTRY(dma, dregs) do { \ - if(DMA_ISBROKEN(dma)) DMA_INTSOFF(dregs); \ - } while (0) - -#define DMA_IRQ_EXIT(dma, dregs) do { \ - if(DMA_ISBROKEN(dma)) DMA_INTSON(dregs); \ - } while(0) - -#define for_each_dvma(dma) \ - for((dma) = dma_chain; (dma); (dma) = (dma)->next) - -/* From PCI */ - -#ifdef CONFIG_PCI -extern int isa_dma_bridge_buggy; -#else -#define isa_dma_bridge_buggy (0) -#endif - -#endif /* !(_ASM_SPARC64_DMA_H) */ diff --git a/arch/sparc/include/asm/floppy_32.h b/arch/sparc/include/asm/floppy_32.h index ae3f00bf22ff..ff2b91c6eeff 100644 --- a/arch/sparc/include/asm/floppy_32.h +++ b/arch/sparc/include/asm/floppy_32.h @@ -385,4 +385,15 @@ static int sparc_eject(void) #define EXTRA_FLOPPY_PARAMS +static DEFINE_SPINLOCK(dma_spin_lock); + +#define claim_dma_lock() \ +({ unsigned long flags; \ + spin_lock_irqsave(&dma_spin_lock, flags); \ + flags; \ +}) + +#define release_dma_lock(__flags) \ + spin_unlock_irqrestore(&dma_spin_lock, __flags); + #endif /* !(__ASM_SPARC_FLOPPY_H) */ |