diff options
Diffstat (limited to 'arch/arm/boot')
58 files changed, 5249 insertions, 429 deletions
diff --git a/arch/arm/boot/compressed/head-xscale.S b/arch/arm/boot/compressed/head-xscale.S index aa5ee49c5c5a..6ab0599c02dd 100644 --- a/arch/arm/boot/compressed/head-xscale.S +++ b/arch/arm/boot/compressed/head-xscale.S @@ -32,10 +32,3 @@ __XScale_start: bic r0, r0, #0x1000 @ clear Icache mcr p15, 0, r0, c1, c0, 0 -#ifdef CONFIG_ARCH_IXP2000 - mov r1, #-1 - mov r0, #0xd6000000 - str r1, [r0, #0x14] - str r1, [r0, #0x18] -#endif - diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S index dc7e8ce8e6be..b8c64b80bafc 100644 --- a/arch/arm/boot/compressed/head.S +++ b/arch/arm/boot/compressed/head.S @@ -567,6 +567,12 @@ __armv3_mpu_cache_on: mcr p15, 0, r0, c7, c0, 0 @ invalidate whole cache v3 mov pc, lr +#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH +#define CB_BITS 0x08 +#else +#define CB_BITS 0x0c +#endif + __setup_mmu: sub r3, r4, #16384 @ Page directory size bic r3, r3, #0xff @ Align the pointer bic r3, r3, #0x3f00 @@ -578,17 +584,14 @@ __setup_mmu: sub r3, r4, #16384 @ Page directory size mov r9, r0, lsr #18 mov r9, r9, lsl #18 @ start of RAM add r10, r9, #0x10000000 @ a reasonable RAM size - mov r1, #0x12 - orr r1, r1, #3 << 10 + mov r1, #0x12 @ XN|U + section mapping + orr r1, r1, #3 << 10 @ AP=11 add r2, r3, #16384 1: cmp r1, r9 @ if virt > start of RAM -#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH - orrhs r1, r1, #0x08 @ set cacheable -#else - orrhs r1, r1, #0x0c @ set cacheable, bufferable -#endif - cmp r1, r10 @ if virt > end of RAM - bichs r1, r1, #0x0c @ clear cacheable, bufferable + cmphs r10, r1 @ && end of RAM > virt + bic r1, r1, #0x1c @ clear XN|U + C + B + orrlo r1, r1, #0x10 @ Set XN|U for non-RAM + orrhs r1, r1, r6 @ set RAM section settings str r1, [r0], #4 @ 1:1 mapping add r1, r1, #1048576 teq r0, r2 @@ -599,7 +602,7 @@ __setup_mmu: sub r3, r4, #16384 @ Page directory size * so there is no map overlap problem for up to 1 MB compressed kernel. * If the execution is in RAM then we would only be duplicating the above. */ - mov r1, #0x1e + orr r1, r6, #0x04 @ ensure B is set for this orr r1, r1, #3 << 10 mov r2, pc mov r2, r2, lsr #20 @@ -620,6 +623,7 @@ __arm926ejs_mmu_cache_on: __armv4_mmu_cache_on: mov r12, lr #ifdef CONFIG_MMU + mov r6, #CB_BITS | 0x12 @ U bl __setup_mmu mov r0, #0 mcr p15, 0, r0, c7, c10, 4 @ drain write buffer @@ -641,6 +645,7 @@ __armv7_mmu_cache_on: #ifdef CONFIG_MMU mrc p15, 0, r11, c0, c1, 4 @ read ID_MMFR0 tst r11, #0xf @ VMSA + movne r6, #CB_BITS | 0x02 @ !XN blne __setup_mmu mov r0, #0 mcr p15, 0, r0, c7, c10, 4 @ drain write buffer @@ -655,7 +660,7 @@ __armv7_mmu_cache_on: orr r0, r0, #1 << 25 @ big-endian page tables #endif orrne r0, r0, #1 @ MMU enabled - movne r1, #-1 + movne r1, #0xfffffffd @ domain 0 = client mcrne p15, 0, r3, c2, c0, 0 @ load page table pointer mcrne p15, 0, r1, c3, c0, 0 @ load domain access control #endif @@ -668,6 +673,7 @@ __armv7_mmu_cache_on: __fa526_cache_on: mov r12, lr + mov r6, #CB_BITS | 0x12 @ U bl __setup_mmu mov r0, #0 mcr p15, 0, r0, c7, c7, 0 @ Invalidate whole cache @@ -680,18 +686,6 @@ __fa526_cache_on: mcr p15, 0, r0, c8, c7, 0 @ flush UTLB mov pc, r12 -__arm6_mmu_cache_on: - mov r12, lr - bl __setup_mmu - mov r0, #0 - mcr p15, 0, r0, c7, c0, 0 @ invalidate whole cache v3 - mcr p15, 0, r0, c5, c0, 0 @ invalidate whole TLB v3 - mov r0, #0x30 - bl __common_mmu_cache_on - mov r0, #0 - mcr p15, 0, r0, c5, c0, 0 @ invalidate whole TLB v3 - mov pc, r12 - __common_mmu_cache_on: #ifndef CONFIG_THUMB2_KERNEL #ifndef DEBUG @@ -756,16 +750,6 @@ call_cache_fn: adr r12, proc_types .align 2 .type proc_types,#object proc_types: - .word 0x41560600 @ ARM6/610 - .word 0xffffffe0 - W(b) __arm6_mmu_cache_off @ works, but slow - W(b) __arm6_mmu_cache_off - mov pc, lr - THUMB( nop ) -@ b __arm6_mmu_cache_on @ untested -@ b __arm6_mmu_cache_off -@ b __armv3_mmu_cache_flush - .word 0x00000000 @ old ARM ID .word 0x0000f000 mov pc, lr @@ -777,8 +761,10 @@ proc_types: .word 0x41007000 @ ARM7/710 .word 0xfff8fe00 - W(b) __arm7_mmu_cache_off - W(b) __arm7_mmu_cache_off + mov pc, lr + THUMB( nop ) + mov pc, lr + THUMB( nop ) mov pc, lr THUMB( nop ) @@ -977,21 +963,6 @@ __armv7_mmu_cache_off: mcr p15, 0, r0, c7, c5, 4 @ ISB mov pc, r12 -__arm6_mmu_cache_off: - mov r0, #0x00000030 @ ARM6 control reg. - b __armv3_mmu_cache_off - -__arm7_mmu_cache_off: - mov r0, #0x00000070 @ ARM7 control reg. - b __armv3_mmu_cache_off - -__armv3_mmu_cache_off: - mcr p15, 0, r0, c1, c0, 0 @ turn MMU and cache off - mov r0, #0 - mcr p15, 0, r0, c7, c0, 0 @ invalidate whole cache v3 - mcr p15, 0, r0, c5, c0, 0 @ invalidate whole TLB v3 - mov pc, lr - /* * Clean and flush the cache to maintain consistency. * diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi new file mode 100644 index 000000000000..f449efc9825f --- /dev/null +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -0,0 +1,273 @@ +/* + * at91sam9260.dtsi - Device Tree Include file for AT91SAM9260 family SoC + * + * Copyright (C) 2011 Atmel, + * 2011 Nicolas Ferre <nicolas.ferre@atmel.com>, + * 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 or later. + */ + +/include/ "skeleton.dtsi" + +/ { + model = "Atmel AT91SAM9260 family SoC"; + compatible = "atmel,at91sam9260"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + serial4 = &usart3; + serial5 = &usart4; + serial6 = &usart5; + gpio0 = &pioA; + gpio1 = &pioB; + gpio2 = &pioC; + tcb0 = &tcb0; + tcb1 = &tcb1; + }; + cpus { + cpu@0 { + compatible = "arm,arm926ejs"; + }; + }; + + memory { + reg = <0x20000000 0x04000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + aic: interrupt-controller@fffff000 { + #interrupt-cells = <2>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + reg = <0xfffff000 0x200>; + }; + + ramc0: ramc@ffffea00 { + compatible = "atmel,at91sam9260-sdramc"; + reg = <0xffffea00 0x200>; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + + shdwc@fffffd10 { + compatible = "atmel,at91sam9260-shdwc"; + reg = <0xfffffd10 0x10>; + }; + + pit: timer@fffffd30 { + compatible = "atmel,at91sam9260-pit"; + reg = <0xfffffd30 0xf>; + interrupts = <1 4>; + }; + + tcb0: timer@fffa0000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffa0000 0x100>; + interrupts = <17 4 18 4 19 4>; + }; + + tcb1: timer@fffdc000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfffdc000 0x100>; + interrupts = <26 4 27 4 28 4>; + }; + + pioA: gpio@fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioB: gpio@fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x100>; + interrupts = <3 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioC: gpio@fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x100>; + interrupts = <4 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + dbgu: serial@fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 4>; + status = "disabled"; + }; + + usart0: serial@fffb0000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb0000 0x200>; + interrupts = <6 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart1: serial@fffb4000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb4000 0x200>; + interrupts = <7 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart2: serial@fffb8000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffb8000 0x200>; + interrupts = <8 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart3: serial@fffd0000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffd0000 0x200>; + interrupts = <23 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart4: serial@fffd4000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffd4000 0x200>; + interrupts = <24 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart5: serial@fffd8000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffd8000 0x200>; + interrupts = <25 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + macb0: ethernet@fffc4000 { + compatible = "cdns,at32ap7000-macb", "cdns,macb"; + reg = <0xfffc4000 0x100>; + interrupts = <21 4>; + status = "disabled"; + }; + + usb1: gadget@fffa4000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfffa4000 0x4000>; + interrupts = <10 4>; + status = "disabled"; + }; + + adc0: adc@fffe0000 { + compatible = "atmel,at91sam9260-adc"; + reg = <0xfffe0000 0x100>; + interrupts = <5 4>; + atmel,adc-use-external-triggers; + atmel,adc-channels-used = <0xf>; + atmel,adc-vref = <3300>; + atmel,adc-num-channels = <4>; + atmel,adc-startup-time = <15>; + atmel,adc-channel-base = <0x30>; + atmel,adc-drdy-mask = <0x10000>; + atmel,adc-status-register = <0x1c>; + atmel,adc-trigger-register = <0x04>; + + trigger@0 { + trigger-name = "timer-counter-0"; + trigger-value = <0x1>; + }; + trigger@1 { + trigger-name = "timer-counter-1"; + trigger-value = <0x3>; + }; + + trigger@2 { + trigger-name = "timer-counter-2"; + trigger-value = <0x5>; + }; + + trigger@3 { + trigger-name = "external"; + trigger-value = <0x13>; + trigger-external; + }; + }; + }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioC 13 0 + &pioC 14 0 + 0 + >; + status = "disabled"; + }; + + usb0: ohci@00500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x100000>; + interrupts = <20 4>; + status = "disabled"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi new file mode 100644 index 000000000000..0209913a65a2 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -0,0 +1,220 @@ +/* + * at91sam9263.dtsi - Device Tree Include file for AT91SAM9263 family SoC + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 only. + */ + +/include/ "skeleton.dtsi" + +/ { + model = "Atmel AT91SAM9263 family SoC"; + compatible = "atmel,at91sam9263"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + gpio0 = &pioA; + gpio1 = &pioB; + gpio2 = &pioC; + gpio3 = &pioD; + gpio4 = &pioE; + tcb0 = &tcb0; + }; + cpus { + cpu@0 { + compatible = "arm,arm926ejs"; + }; + }; + + memory { + reg = <0x20000000 0x08000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + aic: interrupt-controller@fffff000 { + #interrupt-cells = <2>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + reg = <0xfffff000 0x200>; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; + + ramc: ramc@ffffe200 { + compatible = "atmel,at91sam9260-sdramc"; + reg = <0xffffe200 0x200 + 0xffffe800 0x200>; + }; + + pit: timer@fffffd30 { + compatible = "atmel,at91sam9260-pit"; + reg = <0xfffffd30 0xf>; + interrupts = <1 4>; + }; + + tcb0: timer@fff7c000 { + compatible = "atmel,at91rm9200-tcb"; + reg = <0xfff7c000 0x100>; + interrupts = <19 4>; + }; + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + + shdwc@fffffd10 { + compatible = "atmel,at91sam9260-shdwc"; + reg = <0xfffffd10 0x10>; + }; + + pioA: gpio@fffff200 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff200 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioB: gpio@fffff400 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x100>; + interrupts = <3 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioC: gpio@fffff600 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x100>; + interrupts = <4 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioD: gpio@fffff800 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x100>; + interrupts = <4 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioE: gpio@fffffa00 { + compatible = "atmel,at91rm9200-gpio"; + reg = <0xfffffa00 0x100>; + interrupts = <4 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + dbgu: serial@ffffee00 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xffffee00 0x200>; + interrupts = <1 4>; + status = "disabled"; + }; + + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x200>; + interrupts = <7 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart1: serial@fff90000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff90000 0x200>; + interrupts = <8 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart2: serial@fff94000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff94000 0x200>; + interrupts = <9 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + macb0: ethernet@fffbc000 { + compatible = "cdns,at32ap7000-macb", "cdns,macb"; + reg = <0xfffbc000 0x100>; + interrupts = <21 4>; + status = "disabled"; + }; + + usb1: gadget@fff78000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfff78000 0x4000>; + interrupts = <24 4>; + status = "disabled"; + }; + }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe000 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioA 22 0 + &pioD 15 0 + 0 + >; + status = "disabled"; + }; + + usb0: ohci@00a00000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00a00000 0x100000>; + interrupts = <29 4>; + status = "disabled"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioB 4 0 /* sda */ + &pioB 5 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts new file mode 100644 index 000000000000..f86ac4b609fc --- /dev/null +++ b/arch/arm/boot/dts/at91sam9263ek.dts @@ -0,0 +1,156 @@ +/* + * at91sam9263ek.dts - Device Tree file for Atmel at91sam9263 reference board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 only + */ +/dts-v1/; +/include/ "at91sam9263.dtsi" + +/ { + model = "Atmel at91sam9263ek"; + compatible = "atmel,at91sam9263ek", "atmel,at91sam9263", "atmel,at91sam9"; + + chosen { + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <16367660>; + }; + }; + + ahb { + apb { + dbgu: serial@ffffee00 { + status = "okay"; + }; + + usart0: serial@fff8c000 { + status = "okay"; + }; + + macb0: ethernet@fffbc000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fff78000 { + atmel,vbus-gpio = <&pioA 25 0>; + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt = <1>; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + oftree@80000 { + label = "oftree"; + reg = <0xa0000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xc0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4c0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7cc0000 0x8340000>; + }; + }; + + usb0: ohci@00a00000 { + num-ports = <2>; + status = "okay"; + atmel,vbus-gpio = <&pioA 24 0 + &pioA 21 0 + >; + }; + }; + + leds { + compatible = "gpio-leds"; + + d3 { + label = "d3"; + gpios = <&pioB 7 0>; + linux,default-trigger = "heartbeat"; + }; + + d2 { + label = "d2"; + gpios = <&pioC 29 1>; + linux,default-trigger = "nand-disk"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + left_click { + label = "left_click"; + gpios = <&pioC 5 1>; + linux,code = <272>; + gpio-key,wakeup; + }; + + right_click { + label = "right_click"; + gpios = <&pioC 4 1>; + linux,code = <273>; + gpio-key,wakeup; + }; + }; + + i2c@0 { + status = "okay"; + + 24c512@50 { + compatible = "24c512"; + reg = <0x50>; + pagesize = <128>; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g20.dtsi b/arch/arm/boot/dts/at91sam9g20.dtsi index 773ef484037a..2a1d1ca8bd86 100644 --- a/arch/arm/boot/dts/at91sam9g20.dtsi +++ b/arch/arm/boot/dts/at91sam9g20.dtsi @@ -1,238 +1,26 @@ /* * at91sam9g20.dtsi - Device Tree Include file for AT91SAM9G20 family SoC * - * Copyright (C) 2011 Atmel, - * 2011 Nicolas Ferre <nicolas.ferre@atmel.com>, - * 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> * - * Licensed under GPLv2 or later. + * Licensed under GPLv2. */ -/include/ "skeleton.dtsi" +/include/ "at91sam9260.dtsi" / { model = "Atmel AT91SAM9G20 family SoC"; compatible = "atmel,at91sam9g20"; - interrupt-parent = <&aic>; - - aliases { - serial0 = &dbgu; - serial1 = &usart0; - serial2 = &usart1; - serial3 = &usart2; - serial4 = &usart3; - serial5 = &usart4; - serial6 = &usart5; - gpio0 = &pioA; - gpio1 = &pioB; - gpio2 = &pioC; - tcb0 = &tcb0; - tcb1 = &tcb1; - }; - cpus { - cpu@0 { - compatible = "arm,arm926ejs"; - }; - }; memory { reg = <0x20000000 0x08000000>; }; ahb { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - apb { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - aic: interrupt-controller@fffff000 { - #interrupt-cells = <2>; - compatible = "atmel,at91rm9200-aic"; - interrupt-controller; - reg = <0xfffff000 0x200>; - }; - - ramc0: ramc@ffffea00 { - compatible = "atmel,at91sam9260-sdramc"; - reg = <0xffffea00 0x200>; - }; - - pmc: pmc@fffffc00 { - compatible = "atmel,at91rm9200-pmc"; - reg = <0xfffffc00 0x100>; - }; - - rstc@fffffd00 { - compatible = "atmel,at91sam9260-rstc"; - reg = <0xfffffd00 0x10>; - }; - - shdwc@fffffd10 { - compatible = "atmel,at91sam9260-shdwc"; - reg = <0xfffffd10 0x10>; - }; - - pit: timer@fffffd30 { - compatible = "atmel,at91sam9260-pit"; - reg = <0xfffffd30 0xf>; - interrupts = <1 4>; - }; - - tcb0: timer@fffa0000 { - compatible = "atmel,at91rm9200-tcb"; - reg = <0xfffa0000 0x100>; - interrupts = <17 4 18 4 19 4>; - }; - - tcb1: timer@fffdc000 { - compatible = "atmel,at91rm9200-tcb"; - reg = <0xfffdc000 0x100>; - interrupts = <26 4 27 4 28 4>; - }; - - pioA: gpio@fffff400 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff400 0x100>; - interrupts = <2 4>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - }; - - pioB: gpio@fffff600 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff600 0x100>; - interrupts = <3 4>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - }; - - pioC: gpio@fffff800 { - compatible = "atmel,at91rm9200-gpio"; - reg = <0xfffff800 0x100>; - interrupts = <4 4>; - #gpio-cells = <2>; - gpio-controller; - interrupt-controller; - }; - - dbgu: serial@fffff200 { - compatible = "atmel,at91sam9260-usart"; - reg = <0xfffff200 0x200>; - interrupts = <1 4>; - status = "disabled"; - }; - - usart0: serial@fffb0000 { - compatible = "atmel,at91sam9260-usart"; - reg = <0xfffb0000 0x200>; - interrupts = <6 4>; - atmel,use-dma-rx; - atmel,use-dma-tx; - status = "disabled"; - }; - - usart1: serial@fffb4000 { - compatible = "atmel,at91sam9260-usart"; - reg = <0xfffb4000 0x200>; - interrupts = <7 4>; - atmel,use-dma-rx; - atmel,use-dma-tx; - status = "disabled"; - }; - - usart2: serial@fffb8000 { - compatible = "atmel,at91sam9260-usart"; - reg = <0xfffb8000 0x200>; - interrupts = <8 4>; - atmel,use-dma-rx; - atmel,use-dma-tx; - status = "disabled"; - }; - - usart3: serial@fffd0000 { - compatible = "atmel,at91sam9260-usart"; - reg = <0xfffd0000 0x200>; - interrupts = <23 4>; - atmel,use-dma-rx; - atmel,use-dma-tx; - status = "disabled"; - }; - - usart4: serial@fffd4000 { - compatible = "atmel,at91sam9260-usart"; - reg = <0xfffd4000 0x200>; - interrupts = <24 4>; - atmel,use-dma-rx; - atmel,use-dma-tx; - status = "disabled"; - }; - - usart5: serial@fffd8000 { - compatible = "atmel,at91sam9260-usart"; - reg = <0xfffd8000 0x200>; - interrupts = <25 4>; - atmel,use-dma-rx; - atmel,use-dma-tx; - status = "disabled"; - }; - - macb0: ethernet@fffc4000 { - compatible = "cdns,at32ap7000-macb", "cdns,macb"; - reg = <0xfffc4000 0x100>; - interrupts = <21 4>; - status = "disabled"; - }; - - usb1: gadget@fffa4000 { - compatible = "atmel,at91rm9200-udc"; - reg = <0xfffa4000 0x4000>; - interrupts = <10 4>; - status = "disabled"; + adc0: adc@fffe0000 { + atmel,adc-startup-time = <40>; }; }; - - nand0: nand@40000000 { - compatible = "atmel,at91rm9200-nand"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x40000000 0x10000000 - 0xffffe800 0x200 - >; - atmel,nand-addr-offset = <21>; - atmel,nand-cmd-offset = <22>; - gpios = <&pioC 13 0 - &pioC 14 0 - 0 - >; - status = "disabled"; - }; - - usb0: ohci@00500000 { - compatible = "atmel,at91rm9200-ohci", "usb-ohci"; - reg = <0x00500000 0x100000>; - interrupts = <20 4>; - status = "disabled"; - }; - }; - - i2c@0 { - compatible = "i2c-gpio"; - gpios = <&pioA 23 0 /* sda */ - &pioA 24 0 /* scl */ - >; - i2c-gpio,sda-open-drain; - i2c-gpio,scl-open-drain; - i2c-gpio,delay-us = <2>; /* ~100 kHz */ - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/at91sam9g20ek.dts b/arch/arm/boot/dts/at91sam9g20ek.dts new file mode 100644 index 000000000000..e5324bf9d529 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g20ek.dts @@ -0,0 +1,29 @@ +/* + * at91sam9g20ek.dts - Device Tree file for Atmel at91sam9g20ek board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ +/dts-v1/; +/include/ "at91sam9g20ek_common.dtsi" + +/ { + model = "Atmel at91sam9g20ek"; + compatible = "atmel,at91sam9g20ek", "atmel,at91sam9g20", "atmel,at91sam9"; + + leds { + compatible = "gpio-leds"; + + ds1 { + label = "ds1"; + gpios = <&pioA 9 0>; + linux,default-trigger = "heartbeat"; + }; + + ds5 { + label = "ds5"; + gpios = <&pioA 6 1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts new file mode 100644 index 000000000000..f1b2e148ac8c --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts @@ -0,0 +1,29 @@ +/* + * at91sam9g20ek_2mmc.dts - Device Tree file for Atmel at91sam9g20ek 2 MMC board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ +/dts-v1/; +/include/ "at91sam9g20ek_common.dtsi" + +/ { + model = "Atmel at91sam9g20ek 2 mmc"; + compatible = "atmel,at91sam9g20ek_2mmc", "atmel,at91sam9g20", "atmel,at91sam9"; + + leds { + compatible = "gpio-leds"; + + ds1 { + label = "ds1"; + gpios = <&pioB 9 0>; + linux,default-trigger = "heartbeat"; + }; + + ds5 { + label = "ds5"; + gpios = <&pioB 8 1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi new file mode 100644 index 000000000000..b06c0db273b1 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi @@ -0,0 +1,142 @@ +/* + * at91sam9g20ek_common.dtsi - Device Tree file for Atmel at91sam9g20ek board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ +/include/ "at91sam9g20.dtsi" + +/ { + + chosen { + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <18432000>; + }; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + + usart0: serial@fffb0000 { + status = "okay"; + }; + + usart1: serial@fffb4000 { + status = "okay"; + }; + + macb0: ethernet@fffc4000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fffa4000 { + atmel,vbus-gpio = <&pioC 5 0>; + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + oftree@80000 { + label = "oftree"; + reg = <0xa0000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xc0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4c0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7cc0000 0x8340000>; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + status = "okay"; + }; + }; + + i2c@0 { + status = "okay"; + + 24c512@50 { + compatible = "24c512"; + reg = <0x50>; + }; + + wm8731@1b { + compatible = "wm8731"; + reg = <0x1b>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + btn3 { + label = "Buttin 3"; + gpios = <&pioA 30 1>; + linux,code = <0x103>; + gpio-key,wakeup; + }; + + btn4 { + label = "Buttin 4"; + gpios = <&pioA 31 1>; + linux,code = <0x104>; + gpio-key,wakeup; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index c8042147eaa2..7dbccaf199f7 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -199,6 +199,43 @@ interrupts = <25 4>; status = "disabled"; }; + + adc0: adc@fffb0000 { + compatible = "atmel,at91sam9260-adc"; + reg = <0xfffb0000 0x100>; + interrupts = <20 4>; + atmel,adc-use-external-triggers; + atmel,adc-channels-used = <0xff>; + atmel,adc-vref = <3300>; + atmel,adc-num-channels = <8>; + atmel,adc-startup-time = <40>; + atmel,adc-channel-base = <0x30>; + atmel,adc-drdy-mask = <0x10000>; + atmel,adc-status-register = <0x1c>; + atmel,adc-trigger-register = <0x08>; + + trigger@0 { + trigger-name = "external-rising"; + trigger-value = <0x1>; + trigger-external; + }; + trigger@1 { + trigger-name = "external-falling"; + trigger-value = <0x2>; + trigger-external; + }; + + trigger@2 { + trigger-name = "external-any"; + trigger-value = <0x3>; + trigger-external; + }; + + trigger@3 { + trigger-name = "continuous"; + trigger-value = <0x6>; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi new file mode 100644 index 000000000000..cb84de791b5a --- /dev/null +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -0,0 +1,221 @@ +/* + * at91sam9n12.dtsi - Device Tree include file for AT91SAM9N12 SoC + * + * Copyright (C) 2012 Atmel, + * 2012 Hong Xu <hong.xu@atmel.com> + * + * Licensed under GPLv2 or later. + */ + +/include/ "skeleton.dtsi" + +/ { + model = "Atmel AT91SAM9N12 SoC"; + compatible = "atmel,at91sam9n12"; + interrupt-parent = <&aic>; + + aliases { + serial0 = &dbgu; + serial1 = &usart0; + serial2 = &usart1; + serial3 = &usart2; + serial4 = &usart3; + gpio0 = &pioA; + gpio1 = &pioB; + gpio2 = &pioC; + gpio3 = &pioD; + tcb0 = &tcb0; + tcb1 = &tcb1; + }; + cpus { + cpu@0 { + compatible = "arm,arm926ejs"; + }; + }; + + memory { + reg = <0x20000000 0x10000000>; + }; + + ahb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + apb { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + aic: interrupt-controller@fffff000 { + #interrupt-cells = <2>; + compatible = "atmel,at91rm9200-aic"; + interrupt-controller; + reg = <0xfffff000 0x200>; + }; + + ramc0: ramc@ffffe800 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe800 0x200>; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; + + rstc@fffffe00 { + compatible = "atmel,at91sam9g45-rstc"; + reg = <0xfffffe00 0x10>; + }; + + pit: timer@fffffe30 { + compatible = "atmel,at91sam9260-pit"; + reg = <0xfffffe30 0xf>; + interrupts = <1 4>; + }; + + shdwc@fffffe10 { + compatible = "atmel,at91sam9x5-shdwc"; + reg = <0xfffffe10 0x10>; + }; + + tcb0: timer@f8008000 { + compatible = "atmel,at91sam9x5-tcb"; + reg = <0xf8008000 0x100>; + interrupts = <17 4>; + }; + + tcb1: timer@f800c000 { + compatible = "atmel,at91sam9x5-tcb"; + reg = <0xf800c000 0x100>; + interrupts = <17 4>; + }; + + dma: dma-controller@ffffec00 { + compatible = "atmel,at91sam9g45-dma"; + reg = <0xffffec00 0x200>; + interrupts = <20 4>; + }; + + pioA: gpio@fffff400 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff400 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioB: gpio@fffff600 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff600 0x100>; + interrupts = <2 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioC: gpio@fffff800 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffff800 0x100>; + interrupts = <3 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + pioD: gpio@fffffa00 { + compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; + reg = <0xfffffa00 0x100>; + interrupts = <3 4>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + dbgu: serial@fffff200 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfffff200 0x200>; + interrupts = <1 4>; + status = "disabled"; + }; + + usart0: serial@f801c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf801c000 0x4000>; + interrupts = <5 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart1: serial@f8020000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf8020000 0x4000>; + interrupts = <6 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart2: serial@f8024000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf8024000 0x4000>; + interrupts = <7 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + + usart3: serial@f8028000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf8028000 0x4000>; + interrupts = <8 4>; + atmel,use-dma-rx; + atmel,use-dma-tx; + status = "disabled"; + }; + }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = < 0x40000000 0x10000000 + 0xffffe000 0x00000600 + 0xffffe600 0x00000200 + 0x00100000 0x00100000 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioD 5 0 + &pioD 4 0 + 0 + >; + status = "disabled"; + }; + + usb0: ohci@00500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x00100000>; + interrupts = <22 4>; + status = "disabled"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 30 0 /* sda */ + &pioA 31 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts new file mode 100644 index 000000000000..f4e43e38f3a1 --- /dev/null +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -0,0 +1,84 @@ +/* + * at91sam9n12ek.dts - Device Tree file for AT91SAM9N12-EK board + * + * Copyright (C) 2012 Atmel, + * 2012 Hong Xu <hong.xu@atmel.com> + * + * Licensed under GPLv2 or later. + */ +/dts-v1/; +/include/ "at91sam9n12.dtsi" + +/ { + model = "Atmel AT91SAM9N12-EK"; + compatible = "atmel,at91sam9n12ek", "atmel,at91sam9n12", "atmel,at91sam9"; + + chosen { + bootargs = "mem=128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2"; + }; + + memory { + reg = <0x20000000 0x10000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <16000000>; + }; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + d8 { + label = "d8"; + gpios = <&pioB 4 1>; + linux,default-trigger = "mmc0"; + }; + + d9 { + label = "d6"; + gpios = <&pioB 5 1>; + linux,default-trigger = "nand-disk"; + }; + + d10 { + label = "d7"; + gpios = <&pioB 6 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + enter { + label = "Enter"; + gpios = <&pioB 4 1>; + linux,code = <28>; + gpio-key,wakeup; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index dd4ed748469a..6b3ef4339ae7 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -190,6 +190,44 @@ interrupts = <27 4>; status = "disabled"; }; + + adc0: adc@f804c000 { + compatible = "atmel,at91sam9260-adc"; + reg = <0xf804c000 0x100>; + interrupts = <19 4>; + atmel,adc-use-external; + atmel,adc-channels-used = <0xffff>; + atmel,adc-vref = <3300>; + atmel,adc-num-channels = <12>; + atmel,adc-startup-time = <40>; + atmel,adc-channel-base = <0x50>; + atmel,adc-drdy-mask = <0x1000000>; + atmel,adc-status-register = <0x30>; + atmel,adc-trigger-register = <0xc0>; + + trigger@0 { + trigger-name = "external-rising"; + trigger-value = <0x1>; + trigger-external; + }; + + trigger@1 { + trigger-name = "external-falling"; + trigger-value = <0x2>; + trigger-external; + }; + + trigger@2 { + trigger-name = "external-any"; + trigger-value = <0x3>; + trigger-external; + }; + + trigger@3 { + trigger-name = "continuous"; + trigger-value = <0x6>; + }; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/db8500.dtsi b/arch/arm/boot/dts/db8500.dtsi index 14bc30705099..881bc3987844 100644 --- a/arch/arm/boot/dts/db8500.dtsi +++ b/arch/arm/boot/dts/db8500.dtsi @@ -55,83 +55,101 @@ gpio0: gpio@8012e000 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8012e000 0x80>; interrupts = <0 119 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <0>; }; gpio1: gpio@8012e080 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8012e080 0x80>; interrupts = <0 120 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <1>; }; gpio2: gpio@8000e000 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8000e000 0x80>; interrupts = <0 121 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <2>; }; gpio3: gpio@8000e080 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8000e080 0x80>; interrupts = <0 122 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <3>; }; gpio4: gpio@8000e100 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8000e100 0x80>; interrupts = <0 123 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <4>; }; gpio5: gpio@8000e180 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8000e180 0x80>; interrupts = <0 124 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <5>; }; gpio6: gpio@8011e000 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8011e000 0x80>; interrupts = <0 125 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <6>; }; gpio7: gpio@8011e080 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0x8011e080 0x80>; interrupts = <0 126 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <7>; }; gpio8: gpio@a03fe000 { compatible = "stericsson,db8500-gpio", - "stmicroelectronics,nomadik-gpio"; + "st,nomadik-gpio"; reg = <0xa03fe000 0x80>; interrupts = <0 127 0x4>; supports-sleepmode; gpio-controller; + #gpio-cells = <2>; + gpio-bank = <8>; }; usb@a03e0000 { @@ -153,7 +171,13 @@ reg = <0x80157000 0x1000>; interrupts = <46 47>; #address-cells = <1>; - #size-cells = <0>; + #size-cells = <1>; + ranges; + + prcmu-timer-4@80157450 { + compatible = "stericsson,db8500-prcmu-timer-4"; + reg = <0x80157450 0xC>; + }; ab8500@5 { compatible = "stericsson,ab8500"; @@ -163,7 +187,7 @@ }; i2c@80004000 { - compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c"; + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; reg = <0x80004000 0x1000>; interrupts = <0 21 0x4>; #address-cells = <1>; @@ -171,7 +195,7 @@ }; i2c@80122000 { - compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c"; + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; reg = <0x80122000 0x1000>; interrupts = <0 22 0x4>; #address-cells = <1>; @@ -179,7 +203,7 @@ }; i2c@80128000 { - compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c"; + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; reg = <0x80128000 0x1000>; interrupts = <0 55 0x4>; #address-cells = <1>; @@ -187,7 +211,7 @@ }; i2c@80110000 { - compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c"; + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; reg = <0x80110000 0x1000>; interrupts = <0 12 0x4>; #address-cells = <1>; @@ -195,7 +219,7 @@ }; i2c@8012a000 { - compatible = "stericsson,db8500-i2c", "stmicroelectronics,nomadik-i2c"; + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; reg = <0x8012a000 0x1000>; interrupts = <0 51 0x4>; #address-cells = <1>; @@ -270,5 +294,14 @@ interrupts = <0 100 0x4>; status = "disabled"; }; + + external-bus@50000000 { + compatible = "simple-bus"; + reg = <0x50000000 0x4000000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x50000000 0x4000000>; + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/emev2-kzm9d.dts b/arch/arm/boot/dts/emev2-kzm9d.dts new file mode 100644 index 000000000000..297e3baba71c --- /dev/null +++ b/arch/arm/boot/dts/emev2-kzm9d.dts @@ -0,0 +1,26 @@ +/* + * Device Tree Source for the KZM9D board + * + * Copyright (C) 2012 Renesas Solutions Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ +/dts-v1/; + +/include/ "emev2.dtsi" + +/ { + model = "EMEV2 KZM9D Board"; + compatible = "renesas,kzm9d", "renesas,emev2"; + + memory { + device_type = "memory"; + reg = <0x40000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS1,115200n81"; + }; +}; diff --git a/arch/arm/boot/dts/emev2.dtsi b/arch/arm/boot/dts/emev2.dtsi new file mode 100644 index 000000000000..eb504a6c0f4a --- /dev/null +++ b/arch/arm/boot/dts/emev2.dtsi @@ -0,0 +1,63 @@ +/* + * Device Tree Source for the EMEV2 SoC + * + * Copyright (C) 2012 Renesas Solutions Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/include/ "skeleton.dtsi" + +/ { + compatible = "renesas,emev2"; + interrupt-parent = <&gic>; + + cpus { + cpu@0 { + compatible = "arm,cortex-a9"; + }; + cpu@1 { + compatible = "arm,cortex-a9"; + }; + }; + + gic: interrupt-controller@e0020000 { + compatible = "arm,cortex-a9-gic"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0xe0028000 0x1000>, + <0xe0020000 0x0100>; + }; + + sti@e0180000 { + compatible = "renesas,em-sti"; + reg = <0xe0180000 0x54>; + interrupts = <0 125 0>; + }; + + uart@e1020000 { + compatible = "renesas,em-uart"; + reg = <0xe1020000 0x38>; + interrupts = <0 8 0>; + }; + + uart@e1030000 { + compatible = "renesas,em-uart"; + reg = <0xe1030000 0x38>; + interrupts = <0 9 0>; + }; + + uart@e1040000 { + compatible = "renesas,em-uart"; + reg = <0xe1040000 0x38>; + interrupts = <0 10 0>; + }; + + uart@e1050000 { + compatible = "renesas,em-uart"; + reg = <0xe1050000 0x38>; + interrupts = <0 11 0>; + }; +}; diff --git a/arch/arm/boot/dts/ethernut5.dts b/arch/arm/boot/dts/ethernut5.dts new file mode 100644 index 000000000000..1ea9d34460a4 --- /dev/null +++ b/arch/arm/boot/dts/ethernut5.dts @@ -0,0 +1,84 @@ +/* + * ethernut5.dts - Device Tree file for Ethernut 5 board + * + * Copyright (C) 2012 egnite GmbH <info@egnite.de> + * + * Licensed under GPLv2. + */ +/dts-v1/; +/include/ "at91sam9260.dtsi" + +/ { + model = "Ethernut 5"; + compatible = "egnite,ethernut5", "atmel,at91sam9260", "atmel,at91sam9"; + + chosen { + bootargs = "console=ttyS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2"; + }; + + memory { + reg = <0x20000000 0x08000000>; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + + usart0: serial@fffb0000 { + status = "okay"; + }; + + usart1: serial@fffb4000 { + status = "okay"; + }; + + macb0: ethernet@fffc4000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fffa4000 { + atmel,vbus-gpio = <&pioC 5 0>; + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + gpios = <0 + &pioC 14 0 + 0 + >; + + root@0 { + label = "root"; + reg = <0x0 0x08000000>; + }; + + data@20000 { + label = "data"; + reg = <0x08000000 0x38000000>; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + status = "okay"; + }; + }; + + i2c@0 { + status = "okay"; + + pcf8563@50 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts index c7ee86c2dfb5..139138a556b0 100644 --- a/arch/arm/boot/dts/imx53-smd.dts +++ b/arch/arm/boot/dts/imx53-smd.dts @@ -35,7 +35,7 @@ }; esdhc@50008000 { /* ESDHC2 */ - fsl,card-wired; + non-removable; status = "okay"; }; @@ -76,7 +76,7 @@ }; esdhc@50020000 { /* ESDHC3 */ - fsl,card-wired; + non-removable; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/imx6q-arm2.dts b/arch/arm/boot/dts/imx6q-arm2.dts index ce1c8238c897..d2eaf521c9fd 100644 --- a/arch/arm/boot/dts/imx6q-arm2.dts +++ b/arch/arm/boot/dts/imx6q-arm2.dts @@ -41,7 +41,7 @@ }; usdhc@0219c000 { /* uSDHC4 */ - fsl,card-wired; + non-removable; vmmc-supply = <®_3p3v>; status = "okay"; }; diff --git a/arch/arm/boot/dts/kirkwood-dns320.dts b/arch/arm/boot/dts/kirkwood-dns320.dts new file mode 100644 index 000000000000..dc09a735b04a --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-dns320.dts @@ -0,0 +1,64 @@ +/dts-v1/; + +/include/ "kirkwood.dtsi" + +/ { + model = "D-Link DNS-320 NAS (Rev A1)"; + compatible = "dlink,dns-320-a1", "dlink,dns-320", "dlink,dns-kirkwood", "mrvl,kirkwood-88f6281", "mrvl,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + }; + + ocp@f1000000 { + serial@12000 { + clock-frequency = <166666667>; + status = "okay"; + }; + + serial@12100 { + clock-frequency = <166666667>; + status = "okay"; + }; + + nand@3000000 { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x500000>; + }; + + partition@600000 { + label = "ramdisk"; + reg = <0x0600000 0x500000>; + }; + + partition@b00000 { + label = "image"; + reg = <0x0b00000 0x6600000>; + }; + + partition@7100000 { + label = "mini firmware"; + reg = <0x7100000 0xa00000>; + }; + + partition@7b00000 { + label = "config"; + reg = <0x7b00000 0x500000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-dns325.dts b/arch/arm/boot/dts/kirkwood-dns325.dts new file mode 100644 index 000000000000..c2a5562525d2 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-dns325.dts @@ -0,0 +1,59 @@ +/dts-v1/; + +/include/ "kirkwood.dtsi" + +/ { + model = "D-Link DNS-325 NAS (Rev A1)"; + compatible = "dlink,dns-325-a1", "dlink,dns-325", "dlink,dns-kirkwood", "mrvl,kirkwood-88f6281", "mrvl,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + }; + + ocp@f1000000 { + serial@12000 { + clock-frequency = <200000000>; + status = "okay"; + }; + + nand@3000000 { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x500000>; + }; + + partition@600000 { + label = "ramdisk"; + reg = <0x0600000 0x500000>; + }; + + partition@b00000 { + label = "image"; + reg = <0x0b00000 0x6600000>; + }; + + partition@7100000 { + label = "mini firmware"; + reg = <0x7100000 0xa00000>; + }; + + partition@7b00000 { + label = "config"; + reg = <0x7b00000 0x500000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts new file mode 100644 index 000000000000..ada0f0c23085 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts @@ -0,0 +1,44 @@ +/dts-v1/; + +/include/ "kirkwood.dtsi" + +/ { + model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)"; + compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "mrvl,kirkwood-88f6281", "mrvl,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + }; + + ocp@f1000000 { + serial@12000 { + clock-frequency = <200000000>; + status = "okay"; + }; + + nand@3000000 { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x600000>; + }; + + partition@700000 { + label = "root"; + reg = <0x0700000 0xf900000>; + }; + + }; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts new file mode 100644 index 000000000000..1ba75d4adecc --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-iconnect.dts @@ -0,0 +1,26 @@ +/dts-v1/; + +/include/ "kirkwood.dtsi" + +/ { + model = "Iomega Iconnect"; + compatible = "iom,iconnect-1.1", "iom,iconnect", "mrvl,kirkwood-88f6281", "mrvl,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot)"; + linux,initrd-start = <0x4500040>; + linux,initrd-end = <0x4800000>; + }; + + ocp@f1000000 { + serial@12000 { + clock-frequency = <200000000>; + status = "ok"; + }; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 3474ef890945..926528b81baa 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -5,7 +5,7 @@ ocp@f1000000 { compatible = "simple-bus"; - ranges = <0 0xf1000000 0x1000000>; + ranges = <0 0xf1000000 0x4000000>; #address-cells = <1>; #size-cells = <1>; @@ -32,5 +32,18 @@ reg = <0x10300 0x20>; interrupts = <53>; }; + + nand@3000000 { + #address-cells = <1>; + #size-cells = <1>; + cle = <0>; + ale = <1>; + bank-width = <1>; + compatible = "mrvl,orion-nand"; + reg = <0x3000000 0x400>; + chip-delay = <25>; + /* set partition map and/or chip-delay in board dts */ + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/kizbox.dts b/arch/arm/boot/dts/kizbox.dts new file mode 100644 index 000000000000..e8814fe0e277 --- /dev/null +++ b/arch/arm/boot/dts/kizbox.dts @@ -0,0 +1,138 @@ +/* + * kizbox.dts - Device Tree file for Overkiz Kizbox board + * + * Copyright (C) 2012 Boris BREZILLON <linux-arm@overkiz.com> + * + * Licensed under GPLv2. + */ +/dts-v1/; +/include/ "at91sam9g20.dtsi" + +/ { + + model = "Overkiz kizbox"; + compatible = "overkiz,kizbox", "atmel,at91sam9g20", "atmel,at91sam9"; + + chosen { + bootargs = "panic=5 ubi.mtd=1 rootfstype=ubifs root=ubi0:root"; + }; + + memory { + reg = <0x20000000 0x2000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <18432000>; + }; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + + usart0: serial@fffb0000 { + status = "okay"; + }; + + usart1: serial@fffb4000 { + status = "okay"; + }; + + macb0: ethernet@fffc4000 { + phy-mode = "mii"; + status = "okay"; + }; + + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + status = "okay"; + + bootloaderkernel@0 { + label = "bootloader-kernel"; + reg = <0x0 0xc0000>; + }; + + ubi@c0000 { + label = "ubi"; + reg = <0xc0000 0x7f40000>; + }; + + }; + + usb0: ohci@00500000 { + num-ports = <1>; + status = "okay"; + }; + }; + + i2c@0 { + status = "okay"; + + pcf8563@51 { + /* nxp pcf8563 rtc */ + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + }; + + leds { + compatible = "gpio-leds"; + + led1g { + label = "led1:green"; + gpios = <&pioB 0 1>; + linux,default-trigger = "none"; + }; + + led1r { + label = "led1:red"; + gpios = <&pioB 1 1>; + linux,default-trigger = "none"; + }; + + led2g { + label = "led2:green"; + gpios = <&pioB 2 1>; + linux,default-trigger = "none"; + default-state = "on"; + }; + + led2r { + label = "led2:red"; + gpios = <&pioB 3 1>; + linux,default-trigger = "none"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + reset { + label = "reset"; + gpios = <&pioB 30 1>; + linux,code = <0x100>; + gpio-key,wakeup; + }; + + mode { + label = "mode"; + gpios = <&pioB 31 1>; + linux,code = <0x101>; + gpio-key,wakeup; + }; + }; +};
\ No newline at end of file diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi new file mode 100644 index 000000000000..2d696866f71c --- /dev/null +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -0,0 +1,292 @@ +/* + * NXP LPC32xx SoC + * + * Copyright 2012 Roland Stigge <stigge@antcom.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/include/ "skeleton.dtsi" + +/ { + compatible = "nxp,lpc3220"; + interrupt-parent = <&mic>; + + cpus { + cpu@0 { + compatible = "arm,arm926ejs"; + }; + }; + + ahb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x20000000 0x20000000 0x30000000>; + + /* + * Enable either SLC or MLC + */ + slc: flash@20020000 { + compatible = "nxp,lpc3220-slc"; + reg = <0x20020000 0x1000>; + status = "disable"; + }; + + mlc: flash@200B0000 { + compatible = "nxp,lpc3220-mlc"; + reg = <0x200B0000 0x1000>; + status = "disable"; + }; + + dma@31000000 { + compatible = "arm,pl080", "arm,primecell"; + reg = <0x31000000 0x1000>; + interrupts = <0x1c 0>; + }; + + /* + * Enable either ohci or usbd (gadget)! + */ + ohci@31020000 { + compatible = "nxp,ohci-nxp", "usb-ohci"; + reg = <0x31020000 0x300>; + interrupts = <0x3b 0>; + status = "disable"; + }; + + usbd@31020000 { + compatible = "nxp,lpc3220-udc"; + reg = <0x31020000 0x300>; + interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; + status = "disable"; + }; + + clcd@31040000 { + compatible = "arm,pl110", "arm,primecell"; + reg = <0x31040000 0x1000>; + interrupts = <0x0e 0>; + status = "disable"; + }; + + mac: ethernet@31060000 { + compatible = "nxp,lpc-eth"; + reg = <0x31060000 0x1000>; + interrupts = <0x1d 0>; + }; + + apb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x20000000 0x20000000 0x30000000>; + + ssp0: ssp@20084000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x20084000 0x1000>; + interrupts = <0x14 0>; + }; + + spi1: spi@20088000 { + compatible = "nxp,lpc3220-spi"; + reg = <0x20088000 0x1000>; + }; + + ssp1: ssp@2008c000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0x2008c000 0x1000>; + interrupts = <0x15 0>; + }; + + spi2: spi@20090000 { + compatible = "nxp,lpc3220-spi"; + reg = <0x20090000 0x1000>; + }; + + i2s0: i2s@20094000 { + compatible = "nxp,lpc3220-i2s"; + reg = <0x20094000 0x1000>; + }; + + sd@20098000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x20098000 0x1000>; + interrupts = <0x0f 0>, <0x0d 0>; + }; + + i2s1: i2s@2009C000 { + compatible = "nxp,lpc3220-i2s"; + reg = <0x2009C000 0x1000>; + }; + + uart3: serial@40080000 { + compatible = "nxp,serial"; + reg = <0x40080000 0x1000>; + }; + + uart4: serial@40088000 { + compatible = "nxp,serial"; + reg = <0x40088000 0x1000>; + }; + + uart5: serial@40090000 { + compatible = "nxp,serial"; + reg = <0x40090000 0x1000>; + }; + + uart6: serial@40098000 { + compatible = "nxp,serial"; + reg = <0x40098000 0x1000>; + }; + + i2c1: i2c@400A0000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400A0000 0x100>; + interrupts = <0x33 0>; + #address-cells = <1>; + #size-cells = <0>; + pnx,timeout = <0x64>; + }; + + i2c2: i2c@400A8000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400A8000 0x100>; + interrupts = <0x32 0>; + #address-cells = <1>; + #size-cells = <0>; + pnx,timeout = <0x64>; + }; + + i2cusb: i2c@31020300 { + compatible = "nxp,pnx-i2c"; + reg = <0x31020300 0x100>; + interrupts = <0x3f 0>; + #address-cells = <1>; + #size-cells = <0>; + pnx,timeout = <0x64>; + }; + }; + + fab { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x20000000 0x20000000 0x30000000>; + + /* + * MIC Interrupt controller includes: + * MIC @40008000 + * SIC1 @4000C000 + * SIC2 @40010000 + */ + mic: interrupt-controller@40008000 { + compatible = "nxp,lpc3220-mic"; + interrupt-controller; + reg = <0x40008000 0xC000>; + #interrupt-cells = <2>; + }; + + uart1: serial@40014000 { + compatible = "nxp,serial"; + reg = <0x40014000 0x1000>; + }; + + uart2: serial@40018000 { + compatible = "nxp,serial"; + reg = <0x40018000 0x1000>; + }; + + uart7: serial@4001C000 { + compatible = "nxp,serial"; + reg = <0x4001C000 0x1000>; + }; + + rtc@40024000 { + compatible = "nxp,lpc3220-rtc"; + reg = <0x40024000 0x1000>; + interrupts = <0x34 0>; + }; + + gpio: gpio@40028000 { + compatible = "nxp,lpc3220-gpio"; + reg = <0x40028000 0x1000>; + /* create a private address space for enumeration */ + #address-cells = <1>; + #size-cells = <0>; + + gpio_p0: gpio-bank@0 { + gpio-controller; + #gpio-cells = <2>; + reg = <0>; + }; + + gpio_p1: gpio-bank@1 { + gpio-controller; + #gpio-cells = <2>; + reg = <1>; + }; + + gpio_p2: gpio-bank@2 { + gpio-controller; + #gpio-cells = <2>; + reg = <2>; + }; + + gpio_p3: gpio-bank@3 { + gpio-controller; + #gpio-cells = <2>; + reg = <3>; + }; + + gpi_p3: gpio-bank@4 { + gpio-controller; + #gpio-cells = <2>; + reg = <4>; + }; + + gpo_p3: gpio-bank@5 { + gpio-controller; + #gpio-cells = <2>; + reg = <5>; + }; + }; + + watchdog@4003C000 { + compatible = "nxp,pnx4008-wdt"; + reg = <0x4003C000 0x1000>; + }; + + /* + * TSC vs. ADC: Since those two share the same + * hardware, you need to choose from one of the + * following two and do 'status = "okay";' for one of + * them + */ + + adc@40048000 { + compatible = "nxp,lpc3220-adc"; + reg = <0x40048000 0x1000>; + interrupts = <0x27 0>; + status = "disable"; + }; + + tsc@40048000 { + compatible = "nxp,lpc3220-tsc"; + reg = <0x40048000 0x1000>; + interrupts = <0x27 0>; + status = "disable"; + }; + + key@40050000 { + compatible = "nxp,lpc3220-key"; + reg = <0x40050000 0x1000>; + }; + + }; + }; +}; diff --git a/arch/arm/boot/dts/mmp2-brownstone.dts b/arch/arm/boot/dts/mmp2-brownstone.dts new file mode 100644 index 000000000000..153a4b2d12b5 --- /dev/null +++ b/arch/arm/boot/dts/mmp2-brownstone.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2012 Marvell Technology Group Ltd. + * Author: Haojian Zhuang <haojian.zhuang@marvell.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ + +/dts-v1/; +/include/ "mmp2.dtsi" + +/ { + model = "Marvell MMP2 Aspenite Development Board"; + compatible = "mrvl,mmp2-brownstone", "mrvl,mmp2"; + + chosen { + bootargs = "console=ttyS2,38400 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on"; + }; + + memory { + reg = <0x00000000 0x04000000>; + }; + + soc { + apb@d4000000 { + uart3: uart@d4018000 { + status = "okay"; + }; + twsi1: i2c@d4011000 { + status = "okay"; + }; + rtc: rtc@d4010000 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/mmp2.dtsi new file mode 100644 index 000000000000..80f74e256408 --- /dev/null +++ b/arch/arm/boot/dts/mmp2.dtsi @@ -0,0 +1,220 @@ +/* + * Copyright (C) 2012 Marvell Technology Group Ltd. + * Author: Haojian Zhuang <haojian.zhuang@marvell.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ + +/include/ "skeleton.dtsi" + +/ { + aliases { + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + i2c0 = &twsi1; + i2c1 = &twsi2; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&intc>; + ranges; + + axi@d4200000 { /* AXI */ + compatible = "mrvl,axi-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4200000 0x00200000>; + ranges; + + intc: interrupt-controller@d4282000 { + compatible = "mrvl,mmp2-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0xd4282000 0x1000>; + mrvl,intc-nr-irqs = <64>; + }; + + intcmux4@d4282150 { + compatible = "mrvl,mmp2-mux-intc"; + interrupts = <4>; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x150 0x4>, <0x168 0x4>; + reg-names = "mux status", "mux mask"; + mrvl,intc-nr-irqs = <2>; + }; + + intcmux5: interrupt-controller@d4282154 { + compatible = "mrvl,mmp2-mux-intc"; + interrupts = <5>; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x154 0x4>, <0x16c 0x4>; + reg-names = "mux status", "mux mask"; + mrvl,intc-nr-irqs = <2>; + mrvl,clr-mfp-irq = <1>; + }; + + intcmux9: interrupt-controller@d4282180 { + compatible = "mrvl,mmp2-mux-intc"; + interrupts = <9>; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x180 0x4>, <0x17c 0x4>; + reg-names = "mux status", "mux mask"; + mrvl,intc-nr-irqs = <3>; + }; + + intcmux17: interrupt-controller@d4282158 { + compatible = "mrvl,mmp2-mux-intc"; + interrupts = <17>; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x158 0x4>, <0x170 0x4>; + reg-names = "mux status", "mux mask"; + mrvl,intc-nr-irqs = <5>; + }; + + intcmux35: interrupt-controller@d428215c { + compatible = "mrvl,mmp2-mux-intc"; + interrupts = <35>; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x15c 0x4>, <0x174 0x4>; + reg-names = "mux status", "mux mask"; + mrvl,intc-nr-irqs = <15>; + }; + + intcmux51: interrupt-controller@d4282160 { + compatible = "mrvl,mmp2-mux-intc"; + interrupts = <51>; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x160 0x4>, <0x178 0x4>; + reg-names = "mux status", "mux mask"; + mrvl,intc-nr-irqs = <2>; + }; + + intcmux55: interrupt-controller@d4282188 { + compatible = "mrvl,mmp2-mux-intc"; + interrupts = <55>; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x188 0x4>, <0x184 0x4>; + reg-names = "mux status", "mux mask"; + mrvl,intc-nr-irqs = <2>; + }; + }; + + apb@d4000000 { /* APB */ + compatible = "mrvl,apb-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4000000 0x00200000>; + ranges; + + timer0: timer@d4014000 { + compatible = "mrvl,mmp-timer"; + reg = <0xd4014000 0x100>; + interrupts = <13>; + }; + + uart1: uart@d4030000 { + compatible = "mrvl,mmp-uart"; + reg = <0xd4030000 0x1000>; + interrupts = <27>; + status = "disabled"; + }; + + uart2: uart@d4017000 { + compatible = "mrvl,mmp-uart"; + reg = <0xd4017000 0x1000>; + interrupts = <28>; + status = "disabled"; + }; + + uart3: uart@d4018000 { + compatible = "mrvl,mmp-uart"; + reg = <0xd4018000 0x1000>; + interrupts = <24>; + status = "disabled"; + }; + + uart4: uart@d4016000 { + compatible = "mrvl,mmp-uart"; + reg = <0xd4016000 0x1000>; + interrupts = <46>; + status = "disabled"; + }; + + gpio@d4019000 { + compatible = "mrvl,mmp-gpio"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4019000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <49>; + interrupt-names = "gpio_mux"; + interrupt-controller; + #interrupt-cells = <1>; + ranges; + + gcb0: gpio@d4019000 { + reg = <0xd4019000 0x4>; + }; + + gcb1: gpio@d4019004 { + reg = <0xd4019004 0x4>; + }; + + gcb2: gpio@d4019008 { + reg = <0xd4019008 0x4>; + }; + + gcb3: gpio@d4019100 { + reg = <0xd4019100 0x4>; + }; + + gcb4: gpio@d4019104 { + reg = <0xd4019104 0x4>; + }; + + gcb5: gpio@d4019108 { + reg = <0xd4019108 0x4>; + }; + }; + + twsi1: i2c@d4011000 { + compatible = "mrvl,mmp-twsi"; + reg = <0xd4011000 0x1000>; + interrupts = <7>; + mrvl,i2c-fast-mode; + status = "disabled"; + }; + + twsi2: i2c@d4025000 { + compatible = "mrvl,mmp-twsi"; + reg = <0xd4025000 0x1000>; + interrupts = <58>; + status = "disabled"; + }; + + rtc: rtc@d4010000 { + compatible = "mrvl,mmp-rtc"; + reg = <0xd4010000 0x1000>; + interrupts = <1 0>; + interrupt-names = "rtc 1Hz", "rtc alarm"; + interrupt-parent = <&intcmux5>; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 9f72cd4cf308..5b4506c0a8c4 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -18,3 +18,52 @@ reg = <0x80000000 0x20000000>; /* 512 MB */ }; }; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + vsim: regulator@10 { + compatible = "ti,twl4030-vsim"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + }; + }; +}; + +/include/ "twl4030.dtsi" + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <100000>; + + /* + * Display monitor features are burnt in the EEPROM + * as EDID data. + */ + eeprom@50 { + compatible = "ti,eeprom"; + reg = <0x50>; + }; +}; + +&mmc1 { + vmmc-supply = <&vmmc1>; + vmmc_aux-supply = <&vsim>; + bus-width = <8>; +}; + +&mmc2 { + status = "disable"; +}; + +&mmc3 { + status = "disable"; +}; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index c6121357c1eb..99474fa5fac4 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -69,6 +69,60 @@ reg = <0x48200000 0x1000>; }; + gpio1: gpio@48310000 { + compatible = "ti,omap3-gpio"; + ti,hwmods = "gpio1"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio2: gpio@49050000 { + compatible = "ti,omap3-gpio"; + ti,hwmods = "gpio2"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio3: gpio@49052000 { + compatible = "ti,omap3-gpio"; + ti,hwmods = "gpio3"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio4: gpio@49054000 { + compatible = "ti,omap3-gpio"; + ti,hwmods = "gpio4"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio5: gpio@49056000 { + compatible = "ti,omap3-gpio"; + ti,hwmods = "gpio5"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio6: gpio@49058000 { + compatible = "ti,omap3-gpio"; + ti,hwmods = "gpio6"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + uart1: serial@4806a000 { compatible = "ti,omap3-uart"; ti,hwmods = "uart1"; @@ -113,5 +167,53 @@ #size-cells = <0>; ti,hwmods = "i2c3"; }; + + mcspi1: spi@48098000 { + compatible = "ti,omap2-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; + }; + + mcspi2: spi@4809a000 { + compatible = "ti,omap2-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi2"; + ti,spi-num-cs = <2>; + }; + + mcspi3: spi@480b8000 { + compatible = "ti,omap2-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi3"; + ti,spi-num-cs = <2>; + }; + + mcspi4: spi@480ba000 { + compatible = "ti,omap2-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi4"; + ti,spi-num-cs = <1>; + }; + + mmc1: mmc@4809c000 { + compatible = "ti,omap3-hsmmc"; + ti,hwmods = "mmc1"; + ti,dual-volt; + }; + + mmc2: mmc@480b4000 { + compatible = "ti,omap3-hsmmc"; + ti,hwmods = "mmc2"; + }; + + mmc3: mmc@480ad000 { + compatible = "ti,omap3-hsmmc"; + ti,hwmods = "mmc3"; + }; }; }; diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts index 9755ad5917f8..1efe0c587985 100644 --- a/arch/arm/boot/dts/omap4-panda.dts +++ b/arch/arm/boot/dts/omap4-panda.dts @@ -17,4 +17,75 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1 GB */ }; + + leds { + compatible = "gpio-leds"; + heartbeat { + label = "pandaboard::status1"; + gpios = <&gpio1 7 0>; + linux,default-trigger = "heartbeat"; + }; + + mmc { + label = "pandaboard::status2"; + gpios = <&gpio1 8 0>; + linux,default-trigger = "mmc0"; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ + interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-parent = <&gic>; + }; +}; + +/include/ "twl6030.dtsi" + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <100000>; + + /* + * Display monitor features are burnt in their EEPROM as EDID data. + * The EEPROM is connected as I2C slave device. + */ + eeprom@50 { + compatible = "ti,eeprom"; + reg = <0x50>; + }; +}; + +&i2c4 { + clock-frequency = <400000>; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; + bus-width = <8>; +}; + +&mmc2 { + status = "disable"; +}; + +&mmc3 { + status = "disable"; +}; + +&mmc4 { + status = "disable"; +}; + +&mmc5 { + ti,non-removable; + bus-width = <4>; }; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 63c6b2b2bf42..d08c4d137280 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -17,4 +17,144 @@ device_type = "memory"; reg = <0x80000000 0x40000000>; /* 1 GB */ }; + + vdd_eth: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "VDD_ETH"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 16 0>; /* gpio line 48 */ + enable-active-high; + regulator-boot-on; + }; + + leds { + compatible = "gpio-leds"; + debug0 { + label = "omap4:green:debug0"; + gpios = <&gpio2 29 0>; /* 61 */ + }; + + debug1 { + label = "omap4:green:debug1"; + gpios = <&gpio1 30 0>; /* 30 */ + }; + + debug2 { + label = "omap4:green:debug2"; + gpios = <&gpio1 7 0>; /* 7 */ + }; + + debug3 { + label = "omap4:green:debug3"; + gpios = <&gpio1 8 0>; /* 8 */ + }; + + debug4 { + label = "omap4:green:debug4"; + gpios = <&gpio2 18 0>; /* 50 */ + }; + + user1 { + label = "omap4:blue:user"; + gpios = <&gpio6 9 0>; /* 169 */ + }; + + user2 { + label = "omap4:red:user"; + gpios = <&gpio6 10 0>; /* 170 */ + }; + + user3 { + label = "omap4:green:user"; + gpios = <&gpio5 11 0>; /* 139 */ + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ + interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-parent = <&gic>; + }; +}; + +/include/ "twl6030.dtsi" + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; + + /* + * Temperature Sensor + * http://www.ti.com/lit/ds/symlink/tmp105.pdf + */ + tmp105@48 { + compatible = "ti,tmp105"; + reg = <0x48>; + }; + + /* + * Ambient Light Sensor + * http://www.rohm.com/products/databook/sensor/pdf/bh1780gli-e.pdf + */ + bh1780@29 { + compatible = "rohm,bh1780"; + reg = <0x29>; + }; +}; + +&i2c4 { + clock-frequency = <400000>; + + /* + * 3-Axis Digital Compass + * http://www.sparkfun.com/datasheets/Sensors/Magneto/HMC5843.pdf + */ + hmc5843@1e { + compatible = "honeywell,hmc5843"; + reg = <0x1e>; + }; +}; + +&mcspi1 { + eth@0 { + compatible = "ks8851"; + spi-max-frequency = <24000000>; + reg = <0>; + interrupt-parent = <&gpio2>; + interrupts = <2>; /* gpio line 34 */ + vdd-supply = <&vdd_eth>; + }; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; + bus-width = <8>; +}; + +&mmc2 { + vmmc-supply = <&vaux1>; + bus-width = <8>; + ti,non-removable; +}; + +&mmc3 { + status = "disable"; +}; + +&mmc4 { + status = "disable"; +}; + +&mmc5 { + bus-width = <4>; + ti,non-removable; }; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 3d35559e77bc..359c4979c8aa 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -104,6 +104,60 @@ <0x48240100 0x0100>; }; + gpio1: gpio@4a310000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio1"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio2: gpio@48055000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio2"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio3: gpio@48057000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio3"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio4: gpio@48059000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio4"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio5: gpio@4805b000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio5"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio6: gpio@4805d000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio6"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + uart1: serial@4806a000 { compatible = "ti,omap4-uart"; ti,hwmods = "uart1"; @@ -155,5 +209,68 @@ #size-cells = <0>; ti,hwmods = "i2c4"; }; + + mcspi1: spi@48098000 { + compatible = "ti,omap4-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; + }; + + mcspi2: spi@4809a000 { + compatible = "ti,omap4-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi2"; + ti,spi-num-cs = <2>; + }; + + mcspi3: spi@480b8000 { + compatible = "ti,omap4-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi3"; + ti,spi-num-cs = <2>; + }; + + mcspi4: spi@480ba000 { + compatible = "ti,omap4-mcspi"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "mcspi4"; + ti,spi-num-cs = <1>; + }; + + mmc1: mmc@4809c000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + }; + + mmc2: mmc@480b4000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + }; + + mmc3: mmc@480ad000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + }; + + mmc4: mmc@480d1000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc4"; + ti,needs-special-reset; + }; + + mmc5: mmc@480d5000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc5"; + ti,needs-special-reset; + }; }; }; diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts new file mode 100644 index 000000000000..0167e86314c0 --- /dev/null +++ b/arch/arm/boot/dts/phy3250.dts @@ -0,0 +1,145 @@ +/* + * PHYTEC phyCORE-LPC3250 board + * + * Copyright 2012 Roland Stigge <stigge@antcom.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "lpc32xx.dtsi" + +/ { + model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250"; + compatible = "phytec,phy3250", "nxp,lpc3250"; + #address-cells = <1>; + #size-cells = <1>; + + memory { + device_type = "memory"; + reg = <0 0x4000000>; + }; + + ahb { + mac: ethernet@31060000 { + phy-mode = "rmii"; + use-iram; + }; + + /* Here, choose exactly one from: ohci, usbd */ + ohci@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; + +/* + usbd@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; +*/ + + clcd@31040000 { + status = "okay"; + }; + + /* 64MB Flash via SLC NAND controller */ + slc: flash@20020000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + mtd0@00000000 { + label = "phy3250-boot"; + reg = <0x00000000 0x00064000>; + read-only; + }; + + mtd1@00064000 { + label = "phy3250-uboot"; + reg = <0x00064000 0x00190000>; + read-only; + }; + + mtd2@001f4000 { + label = "phy3250-ubt-prms"; + reg = <0x001f4000 0x00010000>; + }; + + mtd3@00204000 { + label = "phy3250-kernel"; + reg = <0x00204000 0x00400000>; + }; + + mtd4@00604000 { + label = "phy3250-rootfs"; + reg = <0x00604000 0x039fc000>; + }; + }; + + apb { + i2c1: i2c@400A0000 { + clock-frequency = <100000>; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + uda1380: uda1380@18 { + compatible = "nxp,uda1380"; + reg = <0x18>; + power-gpio = <&gpio 0x59 0>; + reset-gpio = <&gpio 0x51 0>; + dac-clk = "wspll"; + }; + }; + + i2c2: i2c@400A8000 { + clock-frequency = <100000>; + }; + + i2cusb: i2c@31020300 { + clock-frequency = <100000>; + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; + }; + + ssp0: ssp@20084000 { + eeprom: at25@0 { + compatible = "atmel,at25"; + }; + }; + }; + + fab { + tsc@40048000 { + status = "okay"; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + led0 { + gpios = <&gpo_p3 1 1>; /* GPO_P3 1, GPIO 80, active low */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + gpios = <&gpo_p3 14 1>; /* GPO_P3 14, GPIO 93, active low */ + linux,default-trigger = "timer"; + default-state = "off"; + }; + }; +}; diff --git a/arch/arm/boot/dts/pxa168.dtsi b/arch/arm/boot/dts/pxa168.dtsi index d32d5128f225..31a718696080 100644 --- a/arch/arm/boot/dts/pxa168.dtsi +++ b/arch/arm/boot/dts/pxa168.dtsi @@ -18,13 +18,6 @@ i2c1 = &twsi2; }; - intc: intc-interrupt-controller@d4282000 { - compatible = "mrvl,mmp-intc", "mrvl,intc"; - interrupt-controller; - #interrupt-cells = <1>; - reg = <0xd4282000 0x1000>; - }; - soc { #address-cells = <1>; #size-cells = <1>; @@ -32,6 +25,23 @@ interrupt-parent = <&intc>; ranges; + axi@d4200000 { /* AXI */ + compatible = "mrvl,axi-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4200000 0x00200000>; + ranges; + + intc: interrupt-controller@d4282000 { + compatible = "mrvl,mmp-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0xd4282000 0x1000>; + mrvl,intc-nr-irqs = <64>; + }; + + }; + apb@d4000000 { /* APB */ compatible = "mrvl,apb-bus", "simple-bus"; #address-cells = <1>; @@ -39,40 +49,65 @@ reg = <0xd4000000 0x00200000>; ranges; + timer0: timer@d4014000 { + compatible = "mrvl,mmp-timer"; + reg = <0xd4014000 0x100>; + interrupts = <13>; + }; + uart1: uart@d4017000 { - compatible = "mrvl,mmp-uart", "mrvl,pxa-uart"; + compatible = "mrvl,mmp-uart"; reg = <0xd4017000 0x1000>; interrupts = <27>; status = "disabled"; }; uart2: uart@d4018000 { - compatible = "mrvl,mmp-uart", "mrvl,pxa-uart"; + compatible = "mrvl,mmp-uart"; reg = <0xd4018000 0x1000>; interrupts = <28>; status = "disabled"; }; uart3: uart@d4026000 { - compatible = "mrvl,mmp-uart", "mrvl,pxa-uart"; + compatible = "mrvl,mmp-uart"; reg = <0xd4026000 0x1000>; interrupts = <29>; status = "disabled"; }; - gpio: gpio@d4019000 { - compatible = "mrvl,mmp-gpio", "mrvl,pxa-gpio"; + gpio@d4019000 { + compatible = "mrvl,mmp-gpio"; + #address-cells = <1>; + #size-cells = <1>; reg = <0xd4019000 0x1000>; + gpio-controller; + #gpio-cells = <2>; interrupts = <49>; interrupt-names = "gpio_mux"; - gpio-controller; - #gpio-cells = <1>; interrupt-controller; #interrupt-cells = <1>; + ranges; + + gcb0: gpio@d4019000 { + reg = <0xd4019000 0x4>; + }; + + gcb1: gpio@d4019004 { + reg = <0xd4019004 0x4>; + }; + + gcb2: gpio@d4019008 { + reg = <0xd4019008 0x4>; + }; + + gcb3: gpio@d4019100 { + reg = <0xd4019100 0x4>; + }; }; twsi1: i2c@d4011000 { - compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c"; + compatible = "mrvl,mmp-twsi"; reg = <0xd4011000 0x1000>; interrupts = <7>; mrvl,i2c-fast-mode; @@ -80,7 +115,7 @@ }; twsi2: i2c@d4025000 { - compatible = "mrvl,mmp-twsi", "mrvl,pxa-i2c"; + compatible = "mrvl,mmp-twsi"; reg = <0xd4025000 0x1000>; interrupts = <58>; status = "disabled"; diff --git a/arch/arm/boot/dts/pxa910-dkb.dts b/arch/arm/boot/dts/pxa910-dkb.dts new file mode 100644 index 000000000000..e92be5a474e7 --- /dev/null +++ b/arch/arm/boot/dts/pxa910-dkb.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2012 Marvell Technology Group Ltd. + * Author: Haojian Zhuang <haojian.zhuang@marvell.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ + +/dts-v1/; +/include/ "pxa910.dtsi" + +/ { + model = "Marvell PXA910 DKB Development Board"; + compatible = "mrvl,pxa910-dkb", "mrvl,pxa910"; + + chosen { + bootargs = "console=ttyS0,115200 root=/dev/nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on"; + }; + + memory { + reg = <0x00000000 0x10000000>; + }; + + soc { + apb@d4000000 { + uart1: uart@d4017000 { + status = "okay"; + }; + twsi1: i2c@d4011000 { + status = "okay"; + }; + rtc: rtc@d4010000 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/pxa910.dtsi b/arch/arm/boot/dts/pxa910.dtsi new file mode 100644 index 000000000000..aebf32de73b4 --- /dev/null +++ b/arch/arm/boot/dts/pxa910.dtsi @@ -0,0 +1,140 @@ +/* + * Copyright (C) 2012 Marvell Technology Group Ltd. + * Author: Haojian Zhuang <haojian.zhuang@marvell.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ + +/include/ "skeleton.dtsi" + +/ { + aliases { + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + i2c0 = &twsi1; + i2c1 = &twsi2; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&intc>; + ranges; + + axi@d4200000 { /* AXI */ + compatible = "mrvl,axi-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4200000 0x00200000>; + ranges; + + intc: interrupt-controller@d4282000 { + compatible = "mrvl,mmp-intc"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0xd4282000 0x1000>; + mrvl,intc-nr-irqs = <64>; + }; + + }; + + apb@d4000000 { /* APB */ + compatible = "mrvl,apb-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4000000 0x00200000>; + ranges; + + timer0: timer@d4014000 { + compatible = "mrvl,mmp-timer"; + reg = <0xd4014000 0x100>; + interrupts = <13>; + }; + + timer1: timer@d4016000 { + compatible = "mrvl,mmp-timer"; + reg = <0xd4016000 0x100>; + interrupts = <29>; + status = "disabled"; + }; + + uart1: uart@d4017000 { + compatible = "mrvl,mmp-uart"; + reg = <0xd4017000 0x1000>; + interrupts = <27>; + status = "disabled"; + }; + + uart2: uart@d4018000 { + compatible = "mrvl,mmp-uart"; + reg = <0xd4018000 0x1000>; + interrupts = <28>; + status = "disabled"; + }; + + uart3: uart@d4036000 { + compatible = "mrvl,mmp-uart"; + reg = <0xd4036000 0x1000>; + interrupts = <59>; + status = "disabled"; + }; + + gpio@d4019000 { + compatible = "mrvl,mmp-gpio"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0xd4019000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupts = <49>; + interrupt-names = "gpio_mux"; + interrupt-controller; + #interrupt-cells = <1>; + ranges; + + gcb0: gpio@d4019000 { + reg = <0xd4019000 0x4>; + }; + + gcb1: gpio@d4019004 { + reg = <0xd4019004 0x4>; + }; + + gcb2: gpio@d4019008 { + reg = <0xd4019008 0x4>; + }; + + gcb3: gpio@d4019100 { + reg = <0xd4019100 0x4>; + }; + }; + + twsi1: i2c@d4011000 { + compatible = "mrvl,mmp-twsi"; + reg = <0xd4011000 0x1000>; + interrupts = <7>; + mrvl,i2c-fast-mode; + status = "disabled"; + }; + + twsi2: i2c@d4037000 { + compatible = "mrvl,mmp-twsi"; + reg = <0xd4037000 0x1000>; + interrupts = <54>; + status = "disabled"; + }; + + rtc: rtc@d4010000 { + compatible = "mrvl,mmp-rtc"; + reg = <0xd4010000 0x1000>; + interrupts = <5 6>; + interrupt-names = "rtc 1Hz", "rtc alarm"; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts new file mode 100644 index 000000000000..a7505a95a3b7 --- /dev/null +++ b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts @@ -0,0 +1,22 @@ +/* + * Device Tree Source for the armadillo 800 eva board + * + * Copyright (C) 2012 Renesas Solutions Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/dts-v1/; +/include/ "skeleton.dtsi" + +/ { + model = "armadillo 800 eva"; + compatible = "renesas,armadillo800eva"; + + memory { + device_type = "memory"; + reg = <0x40000000 0x20000000>; + }; +}; diff --git a/arch/arm/boot/dts/sh7372.dtsi b/arch/arm/boot/dts/sh7372.dtsi new file mode 100644 index 000000000000..677fc603f8b3 --- /dev/null +++ b/arch/arm/boot/dts/sh7372.dtsi @@ -0,0 +1,21 @@ +/* + * Device Tree Source for the sh7372 SoC + * + * Copyright (C) 2012 Renesas Solutions Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/include/ "skeleton.dtsi" + +/ { + compatible = "renesas,sh7372"; + + cpus { + cpu@0 { + compatible = "arm,cortex-a8"; + }; + }; +}; diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts new file mode 100644 index 000000000000..bcb911951978 --- /dev/null +++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts @@ -0,0 +1,22 @@ +/* + * Device Tree Source for the KZM-A9-GT board + * + * Copyright (C) 2012 Renesas Solutions Corp. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/dts-v1/; +/include/ "skeleton.dtsi" + +/ { + model = "KZM-A9-GT"; + compatible = "renesas,kzm9g", "renesas,sh73a0"; + + memory { + device_type = "memory"; + reg = <0x41000000 0x1e800000>; + }; +}; diff --git a/arch/arm/boot/dts/snowball.dts b/arch/arm/boot/dts/snowball.dts index 359c6d679156..d99dc04f0d91 100644 --- a/arch/arm/boot/dts/snowball.dts +++ b/arch/arm/boot/dts/snowball.dts @@ -30,35 +30,35 @@ wakeup = <1>; linux,code = <2>; label = "userpb"; - gpios = <&gpio1 0>; + gpios = <&gpio1 0 0>; }; button@2 { debounce_interval = <50>; wakeup = <1>; linux,code = <3>; - label = "userpb"; - gpios = <&gpio4 23>; + label = "extkb1"; + gpios = <&gpio4 23 0>; }; button@3 { debounce_interval = <50>; wakeup = <1>; linux,code = <4>; - label = "userpb"; - gpios = <&gpio4 23>; + label = "extkb2"; + gpios = <&gpio4 24 0>; }; button@4 { debounce_interval = <50>; wakeup = <1>; linux,code = <5>; - label = "userpb"; - gpios = <&gpio5 1>; + label = "extkb3"; + gpios = <&gpio5 1 0>; }; button@5 { debounce_interval = <50>; wakeup = <1>; linux,code = <6>; - label = "userpb"; - gpios = <&gpio5 2>; + label = "extkb4"; + gpios = <&gpio5 2 0>; }; }; @@ -73,17 +73,19 @@ soc-u9500 { external-bus@50000000 { - compatible = "simple-bus"; - reg = <0x50000000 0x10000000>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - ethernet@50000000 { - compatible = "smsc,9111"; - reg = <0x50000000 0x10000>; - interrupts = <12>; + status = "okay"; + + ethernet@0 { + compatible = "smsc,lan9115"; + reg = <0 0x10000>; + interrupts = <12 0x1>; interrupt-parent = <&gpio4>; + + reg-shift = <1>; + reg-io-width = <2>; + smsc,force-internal-phy; + smsc,irq-active-high; + smsc,irq-push-pull; }; }; diff --git a/arch/arm/boot/dts/tegra-cardhu.dts b/arch/arm/boot/dts/tegra-cardhu.dts index ac3fb7558459..4a166357172b 100644 --- a/arch/arm/boot/dts/tegra-cardhu.dts +++ b/arch/arm/boot/dts/tegra-cardhu.dts @@ -10,6 +10,59 @@ reg = < 0x80000000 0x40000000 >; }; + pinmux@70000000 { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + sdmmc1_clk_pz0 { + nvidia,pins = "sdmmc1_clk_pz0"; + nvidia,function = "sdmmc1"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + sdmmc1_cmd_pz1 { + nvidia,pins = "sdmmc1_cmd_pz1", + "sdmmc1_dat0_py7", + "sdmmc1_dat1_py6", + "sdmmc1_dat2_py5", + "sdmmc1_dat3_py4"; + nvidia,function = "sdmmc1"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4", + "sdmmc4_rst_n_pcc3"; + nvidia,function = "sdmmc4"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + sdmmc4_dat0_paa0 { + nvidia,pins = "sdmmc4_dat0_paa0", + "sdmmc4_dat1_paa1", + "sdmmc4_dat2_paa2", + "sdmmc4_dat3_paa3", + "sdmmc4_dat4_paa4", + "sdmmc4_dat5_paa5", + "sdmmc4_dat6_paa6", + "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + dap2_fs_pa2 { + nvidia,pins = "dap2_fs_pa2", + "dap2_sclk_pa3", + "dap2_din_pa4", + "dap2_dout_pa5"; + nvidia,function = "i2s1"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + }; + }; + serial@70006000 { clock-frequency = < 408000000 >; }; @@ -48,12 +101,27 @@ i2c@7000d000 { clock-frequency = <100000>; + + wm8903: wm8903@1a { + compatible = "wlf,wm8903"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = <179 0x04>; /* gpio PW3 */ + + gpio-controller; + #gpio-cells = <2>; + + micdet-cfg = <0>; + micdet-delay = <100>; + gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>; + }; }; sdhci@78000000 { cd-gpios = <&gpio 69 0>; /* gpio PI5 */ wp-gpios = <&gpio 155 0>; /* gpio PT3 */ power-gpios = <&gpio 31 0>; /* gpio PD7 */ + bus-width = <4>; }; sdhci@78000200 { @@ -66,5 +134,46 @@ sdhci@78000400 { support-8bit; + bus-width = <8>; + }; + + ahub@70080000 { + i2s@70080300 { + status = "disable"; + }; + + i2s@70080500 { + status = "disable"; + }; + + i2s@70080600 { + status = "disable"; + }; + + i2s@70080700 { + status = "disable"; + }; + }; + + sound { + compatible = "nvidia,tegra-audio-wm8903-cardhu", + "nvidia,tegra-audio-wm8903"; + nvidia,model = "NVIDIA Tegra Cardhu"; + + nvidia,audio-routing = + "Headphone Jack", "HPOUTR", + "Headphone Jack", "HPOUTL", + "Int Spk", "ROP", + "Int Spk", "RON", + "Int Spk", "LOP", + "Int Spk", "LON", + "Mic Jack", "MICBIAS", + "IN1L", "Mic Jack"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&wm8903>; + + nvidia,spkr-en-gpios = <&wm8903 2 0>; + nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */ }; }; diff --git a/arch/arm/boot/dts/tegra-harmony.dts b/arch/arm/boot/dts/tegra-harmony.dts index 6e8447dc0202..7cd513ac5ea6 100644 --- a/arch/arm/boot/dts/tegra-harmony.dts +++ b/arch/arm/boot/dts/tegra-harmony.dts @@ -10,6 +10,230 @@ reg = < 0x00000000 0x40000000 >; }; + pinmux@70000000 { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ata { + nvidia,pins = "ata"; + nvidia,function = "ide"; + }; + atb { + nvidia,pins = "atb", "gma", "gme"; + nvidia,function = "sdio4"; + }; + atc { + nvidia,pins = "atc"; + nvidia,function = "nand"; + }; + atd { + nvidia,pins = "atd", "ate", "gmb", "gmd", "gpu", + "spia", "spib", "spic"; + nvidia,function = "gmi"; + }; + cdev1 { + nvidia,pins = "cdev1"; + nvidia,function = "plla_out"; + }; + cdev2 { + nvidia,pins = "cdev2"; + nvidia,function = "pllp_out4"; + }; + crtp { + nvidia,pins = "crtp"; + nvidia,function = "crt"; + }; + csus { + nvidia,pins = "csus"; + nvidia,function = "vi_sensor_clk"; + }; + dap1 { + nvidia,pins = "dap1"; + nvidia,function = "dap1"; + }; + dap2 { + nvidia,pins = "dap2"; + nvidia,function = "dap2"; + }; + dap3 { + nvidia,pins = "dap3"; + nvidia,function = "dap3"; + }; + dap4 { + nvidia,pins = "dap4"; + nvidia,function = "dap4"; + }; + ddc { + nvidia,pins = "ddc"; + nvidia,function = "i2c2"; + }; + dta { + nvidia,pins = "dta", "dtd"; + nvidia,function = "sdio2"; + }; + dtb { + nvidia,pins = "dtb", "dtc", "dte"; + nvidia,function = "rsvd1"; + }; + dtf { + nvidia,pins = "dtf"; + nvidia,function = "i2c3"; + }; + gmc { + nvidia,pins = "gmc"; + nvidia,function = "uartd"; + }; + gpu7 { + nvidia,pins = "gpu7"; + nvidia,function = "rtck"; + }; + gpv { + nvidia,pins = "gpv", "slxa", "slxk"; + nvidia,function = "pcie"; + }; + hdint { + nvidia,pins = "hdint", "pta"; + nvidia,function = "hdmi"; + }; + i2cp { + nvidia,pins = "i2cp"; + nvidia,function = "i2cp"; + }; + irrx { + nvidia,pins = "irrx", "irtx"; + nvidia,function = "uarta"; + }; + kbca { + nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd", + "kbce", "kbcf"; + nvidia,function = "kbc"; + }; + lcsn { + nvidia,pins = "lcsn", "ld0", "ld1", "ld2", + "ld3", "ld4", "ld5", "ld6", "ld7", + "ld8", "ld9", "ld10", "ld11", "ld12", + "ld13", "ld14", "ld15", "ld16", "ld17", + "ldc", "ldi", "lhp0", "lhp1", "lhp2", + "lhs", "lm0", "lm1", "lpp", "lpw0", + "lpw1", "lpw2", "lsc0", "lsc1", "lsck", + "lsda", "lsdi", "lspi", "lvp0", "lvp1", + "lvs"; + nvidia,function = "displaya"; + }; + owc { + nvidia,pins = "owc", "spdi", "spdo", "uac"; + nvidia,function = "rsvd2"; + }; + pmc { + nvidia,pins = "pmc"; + nvidia,function = "pwr_on"; + }; + rm { + nvidia,pins = "rm"; + nvidia,function = "i2c1"; + }; + sdb { + nvidia,pins = "sdb", "sdc", "sdd"; + nvidia,function = "pwm"; + }; + sdio1 { + nvidia,pins = "sdio1"; + nvidia,function = "sdio1"; + }; + slxc { + nvidia,pins = "slxc", "slxd"; + nvidia,function = "spdif"; + }; + spid { + nvidia,pins = "spid", "spie", "spif"; + nvidia,function = "spi1"; + }; + spig { + nvidia,pins = "spig", "spih"; + nvidia,function = "spi2_alt"; + }; + uaa { + nvidia,pins = "uaa", "uab", "uda"; + nvidia,function = "ulpi"; + }; + uad { + nvidia,pins = "uad"; + nvidia,function = "irda"; + }; + uca { + nvidia,pins = "uca", "ucb"; + nvidia,function = "uartc"; + }; + conf_ata { + nvidia,pins = "ata", "atb", "atc", "atd", "ate", + "cdev1", "cdev2", "dap1", "dtb", "gma", + "gmb", "gmc", "gmd", "gme", "gpu7", + "gpv", "i2cp", "pta", "rm", "slxa", + "slxk", "spia", "spib", "uac"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + conf_ck32 { + nvidia,pins = "ck32", "ddrc", "pmca", "pmcb", + "pmcc", "pmcd", "pmce", "xm2c", "xm2d"; + nvidia,pull = <0>; + }; + conf_csus { + nvidia,pins = "csus", "spid", "spif"; + nvidia,pull = <1>; + nvidia,tristate = <1>; + }; + conf_crtp { + nvidia,pins = "crtp", "dap2", "dap3", "dap4", + "dtc", "dte", "dtf", "gpu", "sdio1", + "slxc", "slxd", "spdi", "spdo", "spig", + "uda"; + nvidia,pull = <0>; + nvidia,tristate = <1>; + }; + conf_ddc { + nvidia,pins = "ddc", "dta", "dtd", "kbca", + "kbcb", "kbcc", "kbcd", "kbce", "kbcf", + "sdc"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + conf_hdint { + nvidia,pins = "hdint", "lcsn", "ldc", "lm1", + "lpw1", "lsc1", "lsck", "lsda", "lsdi", + "lvp0", "owc", "sdb"; + nvidia,tristate = <1>; + }; + conf_irrx { + nvidia,pins = "irrx", "irtx", "sdd", "spic", + "spie", "spih", "uaa", "uab", "uad", + "uca", "ucb"; + nvidia,pull = <2>; + nvidia,tristate = <1>; + }; + conf_lc { + nvidia,pins = "lc", "ls"; + nvidia,pull = <2>; + }; + conf_ld0 { + nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4", + "ld5", "ld6", "ld7", "ld8", "ld9", + "ld10", "ld11", "ld12", "ld13", "ld14", + "ld15", "ld16", "ld17", "ldi", "lhp0", + "lhp1", "lhp2", "lhs", "lm0", "lpp", + "lpw0", "lpw2", "lsc0", "lspi", "lvp1", + "lvs", "pmc"; + nvidia,tristate = <0>; + }; + conf_ld17_0 { + nvidia,pins = "ld17_0", "ld19_18", "ld21_20", + "ld23_22"; + nvidia,pull = <1>; + }; + }; + }; + pmc@7000f400 { nvidia,invert-interrupt; }; @@ -100,6 +324,7 @@ cd-gpios = <&gpio 69 0>; /* gpio PI5 */ wp-gpios = <&gpio 57 0>; /* gpio PH1 */ power-gpios = <&gpio 155 0>; /* gpio PT3 */ + bus-width = <4>; }; sdhci@c8000400 { @@ -111,5 +336,10 @@ wp-gpios = <&gpio 59 0>; /* gpio PH3 */ power-gpios = <&gpio 70 0>; /* gpio PI6 */ support-8bit; + bus-width = <8>; + }; + + usb@c5004000 { + nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */ }; }; diff --git a/arch/arm/boot/dts/tegra-paz00.dts b/arch/arm/boot/dts/tegra-paz00.dts index 6c02abb469d4..8d625e4c5de5 100644 --- a/arch/arm/boot/dts/tegra-paz00.dts +++ b/arch/arm/boot/dts/tegra-paz00.dts @@ -10,6 +10,222 @@ reg = <0x00000000 0x20000000>; }; + pinmux@70000000 { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ata { + nvidia,pins = "ata", "atc", "atd", "ate", + "dap2", "gmb", "gmc", "gmd", "spia", + "spib", "spic", "spid", "spie"; + nvidia,function = "gmi"; + }; + atb { + nvidia,pins = "atb", "gma", "gme"; + nvidia,function = "sdio4"; + }; + cdev1 { + nvidia,pins = "cdev1"; + nvidia,function = "plla_out"; + }; + cdev2 { + nvidia,pins = "cdev2"; + nvidia,function = "pllp_out4"; + }; + crtp { + nvidia,pins = "crtp"; + nvidia,function = "crt"; + }; + csus { + nvidia,pins = "csus"; + nvidia,function = "pllc_out1"; + }; + dap1 { + nvidia,pins = "dap1"; + nvidia,function = "dap1"; + }; + dap3 { + nvidia,pins = "dap3"; + nvidia,function = "dap3"; + }; + dap4 { + nvidia,pins = "dap4"; + nvidia,function = "dap4"; + }; + ddc { + nvidia,pins = "ddc"; + nvidia,function = "i2c2"; + }; + dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte"; + nvidia,function = "rsvd1"; + }; + dtf { + nvidia,pins = "dtf"; + nvidia,function = "i2c3"; + }; + gpu { + nvidia,pins = "gpu", "sdb", "sdd"; + nvidia,function = "pwm"; + }; + gpu7 { + nvidia,pins = "gpu7"; + nvidia,function = "rtck"; + }; + gpv { + nvidia,pins = "gpv", "slxa", "slxk"; + nvidia,function = "pcie"; + }; + hdint { + nvidia,pins = "hdint", "pta"; + nvidia,function = "hdmi"; + }; + i2cp { + nvidia,pins = "i2cp"; + nvidia,function = "i2cp"; + }; + irrx { + nvidia,pins = "irrx", "irtx"; + nvidia,function = "uarta"; + }; + kbca { + nvidia,pins = "kbca", "kbcc", "kbce", "kbcf"; + nvidia,function = "kbc"; + }; + kbcb { + nvidia,pins = "kbcb", "kbcd"; + nvidia,function = "sdio2"; + }; + lcsn { + nvidia,pins = "lcsn", "ld0", "ld1", "ld2", + "ld3", "ld4", "ld5", "ld6", "ld7", + "ld8", "ld9", "ld10", "ld11", "ld12", + "ld13", "ld14", "ld15", "ld16", "ld17", + "ldc", "ldi", "lhp0", "lhp1", "lhp2", + "lhs", "lm0", "lm1", "lpp", "lpw0", + "lpw1", "lpw2", "lsc0", "lsc1", "lsck", + "lsda", "lsdi", "lspi", "lvp0", "lvp1", + "lvs"; + nvidia,function = "displaya"; + }; + owc { + nvidia,pins = "owc"; + nvidia,function = "owr"; + }; + pmc { + nvidia,pins = "pmc"; + nvidia,function = "pwr_on"; + }; + rm { + nvidia,pins = "rm"; + nvidia,function = "i2c1"; + }; + sdc { + nvidia,pins = "sdc"; + nvidia,function = "twc"; + }; + sdio1 { + nvidia,pins = "sdio1"; + nvidia,function = "sdio1"; + }; + slxc { + nvidia,pins = "slxc", "slxd"; + nvidia,function = "spi4"; + }; + spdi { + nvidia,pins = "spdi", "spdo"; + nvidia,function = "rsvd2"; + }; + spif { + nvidia,pins = "spif", "uac"; + nvidia,function = "rsvd4"; + }; + spig { + nvidia,pins = "spig", "spih"; + nvidia,function = "spi2_alt"; + }; + uaa { + nvidia,pins = "uaa", "uab", "uda"; + nvidia,function = "ulpi"; + }; + uad { + nvidia,pins = "uad"; + nvidia,function = "spdif"; + }; + uca { + nvidia,pins = "uca", "ucb"; + nvidia,function = "uartc"; + }; + conf_ata { + nvidia,pins = "ata", "atb", "atc", "atd", "ate", + "cdev1", "cdev2", "dap1", "dap2", "dtf", + "gma", "gmb", "gmc", "gmd", "gme", + "gpu", "gpu7", "gpv", "i2cp", "pta", + "rm", "sdio1", "slxk", "spdo", "uac", + "uda"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + conf_ck32 { + nvidia,pins = "ck32", "ddrc", "pmca", "pmcb", + "pmcc", "pmcd", "pmce", "xm2c", "xm2d"; + nvidia,pull = <0>; + }; + conf_crtp { + nvidia,pins = "crtp", "dap3", "dap4", "dtb", + "dtc", "dte", "slxa", "slxc", "slxd", + "spdi"; + nvidia,pull = <0>; + nvidia,tristate = <1>; + }; + conf_csus { + nvidia,pins = "csus", "spia", "spib", "spid", + "spif"; + nvidia,pull = <1>; + nvidia,tristate = <1>; + }; + conf_ddc { + nvidia,pins = "ddc", "irrx", "irtx", "kbca", + "kbcb", "kbcc", "kbcd", "kbce", "kbcf", + "spic", "spig", "uaa", "uab"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + conf_dta { + nvidia,pins = "dta", "dtd", "owc", "sdc", "sdd", + "spie", "spih", "uad", "uca", "ucb"; + nvidia,pull = <2>; + nvidia,tristate = <1>; + }; + conf_hdint { + nvidia,pins = "hdint", "ld0", "ld1", "ld2", + "ld3", "ld4", "ld5", "ld6", "ld7", + "ld8", "ld9", "ld10", "ld11", "ld12", + "ld13", "ld14", "ld15", "ld16", "ld17", + "ldc", "ldi", "lhs", "lsc0", "lspi", + "lvs", "pmc"; + nvidia,tristate = <0>; + }; + conf_lc { + nvidia,pins = "lc", "ls"; + nvidia,pull = <2>; + }; + conf_lcsn { + nvidia,pins = "lcsn", "lhp0", "lhp1", "lhp2", + "lm0", "lm1", "lpp", "lpw0", "lpw1", + "lpw2", "lsc1", "lsck", "lsda", "lsdi", + "lvp0", "lvp1", "sdb"; + nvidia,tristate = <1>; + }; + conf_ld17_0 { + nvidia,pins = "ld17_0", "ld19_18", "ld21_20", + "ld23_22"; + nvidia,pull = <1>; + }; + }; + }; + i2c@7000c000 { clock-frequency = <400000>; @@ -97,6 +313,7 @@ cd-gpios = <&gpio 173 0>; /* gpio PV5 */ wp-gpios = <&gpio 57 0>; /* gpio PH1 */ power-gpios = <&gpio 169 0>; /* gpio PV1 */ + bus-width = <4>; }; sdhci@c8000200 { @@ -109,6 +326,7 @@ sdhci@c8000600 { support-8bit; + bus-width = <8>; }; gpio-keys { @@ -131,4 +349,8 @@ linux,default-trigger = "rfkill0"; }; }; + + usb@c5004000 { + nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */ + }; }; diff --git a/arch/arm/boot/dts/tegra-seaboard.dts b/arch/arm/boot/dts/tegra-seaboard.dts index dbf1c5a171c2..315971993cfd 100644 --- a/arch/arm/boot/dts/tegra-seaboard.dts +++ b/arch/arm/boot/dts/tegra-seaboard.dts @@ -11,6 +11,249 @@ reg = < 0x00000000 0x40000000 >; }; + pinmux@70000000 { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ata { + nvidia,pins = "ata"; + nvidia,function = "ide"; + }; + atb { + nvidia,pins = "atb", "gma", "gme"; + nvidia,function = "sdio4"; + }; + atc { + nvidia,pins = "atc"; + nvidia,function = "nand"; + }; + atd { + nvidia,pins = "atd", "ate", "gmb", "spia", + "spib", "spic"; + nvidia,function = "gmi"; + }; + cdev1 { + nvidia,pins = "cdev1"; + nvidia,function = "plla_out"; + }; + cdev2 { + nvidia,pins = "cdev2"; + nvidia,function = "pllp_out4"; + }; + crtp { + nvidia,pins = "crtp", "lm1"; + nvidia,function = "crt"; + }; + csus { + nvidia,pins = "csus"; + nvidia,function = "vi_sensor_clk"; + }; + dap1 { + nvidia,pins = "dap1"; + nvidia,function = "dap1"; + }; + dap2 { + nvidia,pins = "dap2"; + nvidia,function = "dap2"; + }; + dap3 { + nvidia,pins = "dap3"; + nvidia,function = "dap3"; + }; + dap4 { + nvidia,pins = "dap4"; + nvidia,function = "dap4"; + }; + ddc { + nvidia,pins = "ddc", "owc", "spdi", "spdo", + "uac"; + nvidia,function = "rsvd2"; + }; + dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte"; + nvidia,function = "vi"; + }; + dtf { + nvidia,pins = "dtf"; + nvidia,function = "i2c3"; + }; + gmc { + nvidia,pins = "gmc"; + nvidia,function = "uartd"; + }; + gmd { + nvidia,pins = "gmd"; + nvidia,function = "sflash"; + }; + gpu { + nvidia,pins = "gpu"; + nvidia,function = "pwm"; + }; + gpu7 { + nvidia,pins = "gpu7"; + nvidia,function = "rtck"; + }; + gpv { + nvidia,pins = "gpv", "slxa", "slxk"; + nvidia,function = "pcie"; + }; + hdint { + nvidia,pins = "hdint", "lpw0", "lpw2", "lsc1", + "lsck", "lsda", "pta"; + nvidia,function = "hdmi"; + }; + i2cp { + nvidia,pins = "i2cp"; + nvidia,function = "i2cp"; + }; + irrx { + nvidia,pins = "irrx", "irtx"; + nvidia,function = "uartb"; + }; + kbca { + nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd", + "kbce", "kbcf"; + nvidia,function = "kbc"; + }; + lcsn { + nvidia,pins = "lcsn", "ldc", "lm0", "lpw1", + "lsdi", "lvp0"; + nvidia,function = "rsvd4"; + }; + ld0 { + nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4", + "ld5", "ld6", "ld7", "ld8", "ld9", + "ld10", "ld11", "ld12", "ld13", "ld14", + "ld15", "ld16", "ld17", "ldi", "lhp0", + "lhp1", "lhp2", "lhs", "lpp", "lsc0", + "lspi", "lvp1", "lvs"; + nvidia,function = "displaya"; + }; + pmc { + nvidia,pins = "pmc"; + nvidia,function = "pwr_on"; + }; + rm { + nvidia,pins = "rm"; + nvidia,function = "i2c1"; + }; + sdb { + nvidia,pins = "sdb", "sdc", "sdd"; + nvidia,function = "sdio3"; + }; + sdio1 { + nvidia,pins = "sdio1"; + nvidia,function = "sdio1"; + }; + slxc { + nvidia,pins = "slxc", "slxd"; + nvidia,function = "spdif"; + }; + spid { + nvidia,pins = "spid", "spie", "spif"; + nvidia,function = "spi1"; + }; + spig { + nvidia,pins = "spig", "spih"; + nvidia,function = "spi2_alt"; + }; + uaa { + nvidia,pins = "uaa", "uab", "uda"; + nvidia,function = "ulpi"; + }; + uad { + nvidia,pins = "uad"; + nvidia,function = "irda"; + }; + uca { + nvidia,pins = "uca", "ucb"; + nvidia,function = "uartc"; + }; + conf_ata { + nvidia,pins = "ata", "atb", "atc", "atd", + "cdev1", "cdev2", "dap1", "dap2", + "dap4", "dtf", "gma", "gmc", "gmd", + "gme", "gpu", "gpu7", "i2cp", "irrx", + "irtx", "pta", "rm", "sdc", "sdd", + "slxd", "slxk", "spdi", "spdo", "uac", + "uad", "uca", "ucb", "uda"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + conf_ate { + nvidia,pins = "ate", "csus", "dap3", "ddc", + "gpv", "owc", "slxc", "spib", "spid", + "spie"; + nvidia,pull = <0>; + nvidia,tristate = <1>; + }; + conf_ck32 { + nvidia,pins = "ck32", "ddrc", "pmca", "pmcb", + "pmcc", "pmcd", "pmce", "xm2c", "xm2d"; + nvidia,pull = <0>; + }; + conf_crtp { + nvidia,pins = "crtp", "gmb", "slxa", "spia", + "spig", "spih"; + nvidia,pull = <2>; + nvidia,tristate = <1>; + }; + conf_dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd"; + nvidia,pull = <1>; + nvidia,tristate = <0>; + }; + conf_dte { + nvidia,pins = "dte", "spif"; + nvidia,pull = <1>; + nvidia,tristate = <1>; + }; + conf_hdint { + nvidia,pins = "hdint", "lcsn", "ldc", "lm1", + "lpw1", "lsc1", "lsck", "lsda", "lsdi", + "lvp0"; + nvidia,tristate = <1>; + }; + conf_kbca { + nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd", + "kbce", "kbcf", "sdio1", "spic", "uaa", + "uab"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + conf_lc { + nvidia,pins = "lc", "ls"; + nvidia,pull = <2>; + }; + conf_ld0 { + nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4", + "ld5", "ld6", "ld7", "ld8", "ld9", + "ld10", "ld11", "ld12", "ld13", "ld14", + "ld15", "ld16", "ld17", "ldi", "lhp0", + "lhp1", "lhp2", "lhs", "lm0", "lpp", + "lpw0", "lpw2", "lsc0", "lspi", "lvp1", + "lvs", "pmc", "sdb"; + nvidia,tristate = <0>; + }; + conf_ld17_0 { + nvidia,pins = "ld17_0", "ld19_18", "ld21_20", + "ld23_22"; + nvidia,pull = <1>; + }; + drive_sdio1 { + nvidia,pins = "drive_sdio1"; + nvidia,high-speed-mode = <0>; + nvidia,schmitt = <0>; + nvidia,low-power-mode = <3>; + nvidia,pull-down-strength = <31>; + nvidia,pull-up-strength = <31>; + nvidia,slew-rate-rising = <3>; + nvidia,slew-rate-falling = <3>; + }; + }; + }; + i2c@7000c000 { clock-frequency = <400000>; @@ -104,10 +347,12 @@ cd-gpios = <&gpio 69 0>; /* gpio PI5 */ wp-gpios = <&gpio 57 0>; /* gpio PH1 */ power-gpios = <&gpio 70 0>; /* gpio PI6 */ + bus-width = <4>; }; sdhci@c8000600 { support-8bit; + bus-width = <8>; }; usb@c5000000 { @@ -172,4 +417,8 @@ 0x00000000 0x00000000 0x00000000 0x00000000 >; }; }; + + usb@c5004000 { + nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */ + }; }; diff --git a/arch/arm/boot/dts/tegra-trimslice.dts b/arch/arm/boot/dts/tegra-trimslice.dts index 252476867b54..e4fcf9a8178a 100644 --- a/arch/arm/boot/dts/tegra-trimslice.dts +++ b/arch/arm/boot/dts/tegra-trimslice.dts @@ -10,6 +10,236 @@ reg = < 0x00000000 0x40000000 >; }; + pinmux@70000000 { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ata { + nvidia,pins = "ata"; + nvidia,function = "ide"; + }; + atb { + nvidia,pins = "atb", "gma"; + nvidia,function = "sdio4"; + }; + atc { + nvidia,pins = "atc", "gmb"; + nvidia,function = "nand"; + }; + atd { + nvidia,pins = "atd", "ate", "gme", "pta"; + nvidia,function = "gmi"; + }; + cdev1 { + nvidia,pins = "cdev1"; + nvidia,function = "plla_out"; + }; + cdev2 { + nvidia,pins = "cdev2"; + nvidia,function = "pllp_out4"; + }; + crtp { + nvidia,pins = "crtp"; + nvidia,function = "crt"; + }; + csus { + nvidia,pins = "csus"; + nvidia,function = "vi_sensor_clk"; + }; + dap1 { + nvidia,pins = "dap1"; + nvidia,function = "dap1"; + }; + dap2 { + nvidia,pins = "dap2"; + nvidia,function = "dap2"; + }; + dap3 { + nvidia,pins = "dap3"; + nvidia,function = "dap3"; + }; + dap4 { + nvidia,pins = "dap4"; + nvidia,function = "dap4"; + }; + ddc { + nvidia,pins = "ddc"; + nvidia,function = "i2c2"; + }; + dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte"; + nvidia,function = "vi"; + }; + dtf { + nvidia,pins = "dtf"; + nvidia,function = "i2c3"; + }; + gmc { + nvidia,pins = "gmc", "gmd"; + nvidia,function = "sflash"; + }; + gpu { + nvidia,pins = "gpu"; + nvidia,function = "uarta"; + }; + gpu7 { + nvidia,pins = "gpu7"; + nvidia,function = "rtck"; + }; + gpv { + nvidia,pins = "gpv", "slxa", "slxk"; + nvidia,function = "pcie"; + }; + hdint { + nvidia,pins = "hdint"; + nvidia,function = "hdmi"; + }; + i2cp { + nvidia,pins = "i2cp"; + nvidia,function = "i2cp"; + }; + irrx { + nvidia,pins = "irrx", "irtx"; + nvidia,function = "uartb"; + }; + kbca { + nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd", + "kbce", "kbcf"; + nvidia,function = "kbc"; + }; + lcsn { + nvidia,pins = "lcsn", "ld0", "ld1", "ld2", + "ld3", "ld4", "ld5", "ld6", "ld7", + "ld8", "ld9", "ld10", "ld11", "ld12", + "ld13", "ld14", "ld15", "ld16", "ld17", + "ldc", "ldi", "lhp0", "lhp1", "lhp2", + "lhs", "lm0", "lm1", "lpp", "lpw0", + "lpw1", "lpw2", "lsc0", "lsc1", "lsck", + "lsda", "lsdi", "lspi", "lvp0", "lvp1", + "lvs"; + nvidia,function = "displaya"; + }; + owc { + nvidia,pins = "owc", "uac"; + nvidia,function = "rsvd2"; + }; + pmc { + nvidia,pins = "pmc"; + nvidia,function = "pwr_on"; + }; + rm { + nvidia,pins = "rm"; + nvidia,function = "i2c1"; + }; + sdb { + nvidia,pins = "sdb", "sdc", "sdd"; + nvidia,function = "pwm"; + }; + sdio1 { + nvidia,pins = "sdio1"; + nvidia,function = "sdio1"; + }; + slxc { + nvidia,pins = "slxc", "slxd"; + nvidia,function = "sdio3"; + }; + spdi { + nvidia,pins = "spdi", "spdo"; + nvidia,function = "spdif"; + }; + spia { + nvidia,pins = "spia", "spib", "spic"; + nvidia,function = "spi2"; + }; + spid { + nvidia,pins = "spid", "spie", "spif"; + nvidia,function = "spi1"; + }; + spig { + nvidia,pins = "spig", "spih"; + nvidia,function = "spi2_alt"; + }; + uaa { + nvidia,pins = "uaa", "uab", "uda"; + nvidia,function = "ulpi"; + }; + uad { + nvidia,pins = "uad"; + nvidia,function = "irda"; + }; + uca { + nvidia,pins = "uca", "ucb"; + nvidia,function = "uartc"; + }; + conf_ata { + nvidia,pins = "ata", "atc", "atd", "ate", + "crtp", "dap2", "dap3", "dap4", "dta", + "dtb", "dtc", "dtd", "dte", "gmb", + "gme", "i2cp", "pta", "slxc", "slxd", + "spdi", "spdo", "uda"; + nvidia,pull = <0>; + nvidia,tristate = <1>; + }; + conf_atb { + nvidia,pins = "atb", "cdev1", "cdev2", "dap1", + "gma", "gmc", "gmd", "gpu", "gpu7", + "gpv", "sdio1", "slxa", "slxk", "uac"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + conf_ck32 { + nvidia,pins = "ck32", "ddrc", "pmca", "pmcb", + "pmcc", "pmcd", "pmce", "xm2c", "xm2d"; + nvidia,pull = <0>; + }; + conf_csus { + nvidia,pins = "csus", "spia", "spib", + "spid", "spif"; + nvidia,pull = <1>; + nvidia,tristate = <1>; + }; + conf_ddc { + nvidia,pins = "ddc", "dtf", "rm", "sdc", "sdd"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + conf_hdint { + nvidia,pins = "hdint", "lcsn", "ldc", "lm1", + "lpw1", "lsc1", "lsck", "lsda", "lsdi", + "lvp0", "pmc"; + nvidia,tristate = <1>; + }; + conf_irrx { + nvidia,pins = "irrx", "irtx", "kbca", "kbcb", + "kbcc", "kbcd", "kbce", "kbcf", "owc", + "spic", "spie", "spig", "spih", "uaa", + "uab", "uad", "uca", "ucb"; + nvidia,pull = <2>; + nvidia,tristate = <1>; + }; + conf_lc { + nvidia,pins = "lc", "ls"; + nvidia,pull = <2>; + }; + conf_ld0 { + nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4", + "ld5", "ld6", "ld7", "ld8", "ld9", + "ld10", "ld11", "ld12", "ld13", "ld14", + "ld15", "ld16", "ld17", "ldi", "lhp0", + "lhp1", "lhp2", "lhs", "lm0", "lpp", + "lpw0", "lpw2", "lsc0", "lspi", "lvp1", + "lvs", "sdb"; + nvidia,tristate = <0>; + }; + conf_ld17_0 { + nvidia,pins = "ld17_0", "ld19_18", "ld21_20", + "ld23_22"; + nvidia,pull = <1>; + }; + }; + }; + i2c@7000c000 { clock-frequency = <400000>; }; @@ -74,4 +304,8 @@ cd-gpios = <&gpio 121 0>; wp-gpios = <&gpio 122 0>; }; + + usb@c5004000 { + nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */ + }; }; diff --git a/arch/arm/boot/dts/tegra-ventana.dts b/arch/arm/boot/dts/tegra-ventana.dts index 2dcff8728e90..b922a26747e7 100644 --- a/arch/arm/boot/dts/tegra-ventana.dts +++ b/arch/arm/boot/dts/tegra-ventana.dts @@ -10,6 +10,236 @@ reg = < 0x00000000 0x40000000 >; }; + pinmux@70000000 { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ata { + nvidia,pins = "ata"; + nvidia,function = "ide"; + }; + atb { + nvidia,pins = "atb", "gma", "gme"; + nvidia,function = "sdio4"; + }; + atc { + nvidia,pins = "atc"; + nvidia,function = "nand"; + }; + atd { + nvidia,pins = "atd", "ate", "gmb", "spia", + "spib", "spic"; + nvidia,function = "gmi"; + }; + cdev1 { + nvidia,pins = "cdev1"; + nvidia,function = "plla_out"; + }; + cdev2 { + nvidia,pins = "cdev2"; + nvidia,function = "pllp_out4"; + }; + crtp { + nvidia,pins = "crtp", "lm1"; + nvidia,function = "crt"; + }; + csus { + nvidia,pins = "csus"; + nvidia,function = "vi_sensor_clk"; + }; + dap1 { + nvidia,pins = "dap1"; + nvidia,function = "dap1"; + }; + dap2 { + nvidia,pins = "dap2"; + nvidia,function = "dap2"; + }; + dap3 { + nvidia,pins = "dap3"; + nvidia,function = "dap3"; + }; + dap4 { + nvidia,pins = "dap4"; + nvidia,function = "dap4"; + }; + ddc { + nvidia,pins = "ddc", "owc", "spdi", "spdo", + "uac"; + nvidia,function = "rsvd2"; + }; + dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte"; + nvidia,function = "vi"; + }; + dtf { + nvidia,pins = "dtf"; + nvidia,function = "i2c3"; + }; + gmc { + nvidia,pins = "gmc"; + nvidia,function = "uartd"; + }; + gmd { + nvidia,pins = "gmd"; + nvidia,function = "sflash"; + }; + gpu { + nvidia,pins = "gpu"; + nvidia,function = "pwm"; + }; + gpu7 { + nvidia,pins = "gpu7"; + nvidia,function = "rtck"; + }; + gpv { + nvidia,pins = "gpv", "slxa", "slxk"; + nvidia,function = "pcie"; + }; + hdint { + nvidia,pins = "hdint", "pta"; + nvidia,function = "hdmi"; + }; + i2cp { + nvidia,pins = "i2cp"; + nvidia,function = "i2cp"; + }; + irrx { + nvidia,pins = "irrx", "irtx"; + nvidia,function = "uartb"; + }; + kbca { + nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd", + "kbce", "kbcf"; + nvidia,function = "kbc"; + }; + lcsn { + nvidia,pins = "lcsn", "ldc", "lm0", "lpw1", + "lsdi", "lvp0"; + nvidia,function = "rsvd4"; + }; + ld0 { + nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4", + "ld5", "ld6", "ld7", "ld8", "ld9", + "ld10", "ld11", "ld12", "ld13", "ld14", + "ld15", "ld16", "ld17", "ldi", "lhp0", + "lhp1", "lhp2", "lhs", "lpp", "lpw0", + "lpw2", "lsc0", "lsc1", "lsck", "lsda", + "lspi", "lvp1", "lvs"; + nvidia,function = "displaya"; + }; + pmc { + nvidia,pins = "pmc"; + nvidia,function = "pwr_on"; + }; + rm { + nvidia,pins = "rm"; + nvidia,function = "i2c1"; + }; + sdb { + nvidia,pins = "sdb", "sdc", "sdd", "slxc"; + nvidia,function = "sdio3"; + }; + sdio1 { + nvidia,pins = "sdio1"; + nvidia,function = "sdio1"; + }; + slxd { + nvidia,pins = "slxd"; + nvidia,function = "spdif"; + }; + spid { + nvidia,pins = "spid", "spie", "spif"; + nvidia,function = "spi1"; + }; + spig { + nvidia,pins = "spig", "spih"; + nvidia,function = "spi2_alt"; + }; + uaa { + nvidia,pins = "uaa", "uab", "uda"; + nvidia,function = "ulpi"; + }; + uad { + nvidia,pins = "uad"; + nvidia,function = "irda"; + }; + uca { + nvidia,pins = "uca", "ucb"; + nvidia,function = "uartc"; + }; + conf_ata { + nvidia,pins = "ata", "atb", "atc", "atd", + "cdev1", "cdev2", "dap1", "dap2", + "dap4", "ddc", "dtf", "gma", "gmc", + "gme", "gpu", "gpu7", "i2cp", "irrx", + "irtx", "pta", "rm", "sdc", "sdd", + "slxc", "slxd", "slxk", "spdi", "spdo", + "uac", "uad", "uca", "ucb", "uda"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + conf_ate { + nvidia,pins = "ate", "csus", "dap3", "gmd", + "gpv", "owc", "spia", "spib", "spic", + "spid", "spie", "spig"; + nvidia,pull = <0>; + nvidia,tristate = <1>; + }; + conf_ck32 { + nvidia,pins = "ck32", "ddrc", "pmca", "pmcb", + "pmcc", "pmcd", "pmce", "xm2c", "xm2d"; + nvidia,pull = <0>; + }; + conf_crtp { + nvidia,pins = "crtp", "gmb", "slxa", "spih"; + nvidia,pull = <2>; + nvidia,tristate = <1>; + }; + conf_dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd"; + nvidia,pull = <1>; + nvidia,tristate = <0>; + }; + conf_dte { + nvidia,pins = "dte", "spif"; + nvidia,pull = <1>; + nvidia,tristate = <1>; + }; + conf_hdint { + nvidia,pins = "hdint", "lcsn", "ldc", "lm1", + "lpw1", "lsck", "lsda", "lsdi", "lvp0"; + nvidia,tristate = <1>; + }; + conf_kbca { + nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd", + "kbce", "kbcf", "sdio1", "uaa", "uab"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + conf_lc { + nvidia,pins = "lc", "ls"; + nvidia,pull = <2>; + }; + conf_ld0 { + nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4", + "ld5", "ld6", "ld7", "ld8", "ld9", + "ld10", "ld11", "ld12", "ld13", "ld14", + "ld15", "ld16", "ld17", "ldi", "lhp0", + "lhp1", "lhp2", "lhs", "lm0", "lpp", + "lpw0", "lpw2", "lsc0", "lsc1", "lspi", + "lvp1", "lvs", "pmc", "sdb"; + nvidia,tristate = <0>; + }; + conf_ld17_0 { + nvidia,pins = "ld17_0", "ld19_18", "ld21_20", + "ld23_22"; + nvidia,pull = <1>; + }; + }; + }; + i2c@7000c000 { clock-frequency = <400000>; @@ -100,9 +330,15 @@ cd-gpios = <&gpio 69 0>; /* gpio PI5 */ wp-gpios = <&gpio 57 0>; /* gpio PH1 */ power-gpios = <&gpio 70 0>; /* gpio PI6 */ + bus-width = <4>; }; sdhci@c8000600 { support-8bit; + bus-width = <8>; + }; + + usb@c5004000 { + nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */ }; }; diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index 62a7b39f1c9a..15200a949a81 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -183,4 +183,45 @@ reg = < 0x70000868 0xd0 /* Pad control registers */ 0x70003000 0x3e0 >; /* Mux registers */ }; + + ahub { + compatible = "nvidia,tegra30-ahub"; + reg = <0x70080000 0x200 0x70080200 0x100>; + interrupts = < 0 103 0x04 >; + nvidia,dma-request-selector = <&apbdma 1>; + + ranges; + #address-cells = <1>; + #size-cells = <1>; + + tegra_i2s0: i2s@70080300 { + compatible = "nvidia,tegra30-i2s"; + reg = <0x70080300 0x100>; + nvidia,ahub-cif-ids = <4 4>; + }; + + tegra_i2s1: i2s@70080400 { + compatible = "nvidia,tegra30-i2s"; + reg = <0x70080400 0x100>; + nvidia,ahub-cif-ids = <5 5>; + }; + + tegra_i2s2: i2s@70080500 { + compatible = "nvidia,tegra30-i2s"; + reg = <0x70080500 0x100>; + nvidia,ahub-cif-ids = <6 6>; + }; + + tegra_i2s3: i2s@70080600 { + compatible = "nvidia,tegra30-i2s"; + reg = <0x70080600 0x100>; + nvidia,ahub-cif-ids = <7 7>; + }; + + tegra_i2s4: i2s@70080700 { + compatible = "nvidia,tegra30-i2s"; + reg = <0x70080700 0x100>; + nvidia,ahub-cif-ids = <8 8>; + }; + }; }; diff --git a/arch/arm/boot/dts/tny_a9260.dts b/arch/arm/boot/dts/tny_a9260.dts new file mode 100644 index 000000000000..367a16dcd5ef --- /dev/null +++ b/arch/arm/boot/dts/tny_a9260.dts @@ -0,0 +1,15 @@ +/* + * tny_a9260.dts - Device Tree file for Caloa TNY A9260 board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ +/dts-v1/; +/include/ "at91sam9260.dtsi" +/include/ "tny_a9260_common.dtsi" + +/ { + model = "Calao TNY A9260"; + compatible = "calao,tny-a9260", "atmel,at91sam9260", "atmel,at91sam9"; +}; diff --git a/arch/arm/boot/dts/tny_a9260_common.dtsi b/arch/arm/boot/dts/tny_a9260_common.dtsi new file mode 100644 index 000000000000..0e6d3de2e09e --- /dev/null +++ b/arch/arm/boot/dts/tny_a9260_common.dtsi @@ -0,0 +1,83 @@ +/* + * tny_a9260_common.dtsi - Device Tree file for Caloa TNY A926x board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ + +/ { + chosen { + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock6 rw rootfstype=ubifs"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + oftree@80000 { + label = "oftree"; + reg = <0xa0000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xc0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4c0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7cc0000 0x8340000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/tny_a9263.dts b/arch/arm/boot/dts/tny_a9263.dts new file mode 100644 index 000000000000..dee9c571306b --- /dev/null +++ b/arch/arm/boot/dts/tny_a9263.dts @@ -0,0 +1,97 @@ +/* + * usb_a9263.dts - Device Tree file for Caloa USB A9293 board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 only + */ +/dts-v1/; +/include/ "at91sam9263.dtsi" + +/ { + model = "Calao TNY A9263"; + compatible = "atmel,tny-a9263", "atmel,at91sam9263", "atmel,at91sam9"; + + chosen { + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + dbgu: serial@ffffee00 { + status = "okay"; + }; + + usb1: gadget@fff78000 { + atmel,vbus-gpio = <&pioB 11 0>; + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + oftree@80000 { + label = "oftree"; + reg = <0xa0000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xc0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4c0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7cc0000 0x8340000>; + }; + }; + }; + + i2c@0 { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/tny_a9g20.dts b/arch/arm/boot/dts/tny_a9g20.dts new file mode 100644 index 000000000000..e1ab64c72dba --- /dev/null +++ b/arch/arm/boot/dts/tny_a9g20.dts @@ -0,0 +1,15 @@ +/* + * tny_a9g20.dts - Device Tree file for Caloa TNY A9G20 board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ +/dts-v1/; +/include/ "at91sam9g20.dtsi" +/include/ "tny_a9260_common.dtsi" + +/ { + model = "Calao TNY A9G20"; + compatible = "calao,tny-a9g20", "atmel,at91sam9g20", "atmel,at91sam9"; +}; diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi new file mode 100644 index 000000000000..22f4d1394ed3 --- /dev/null +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -0,0 +1,47 @@ +/* + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Integrated Power Management Chip + */ +&twl { + compatible = "ti,twl4030"; + interrupt-controller; + #interrupt-cells = <1>; + + rtc { + compatible = "ti,twl4030-rtc"; + interrupts = <11>; + }; + + vdac: regulator@0 { + compatible = "ti,twl4030-vdac"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vpll2: regulator@1 { + compatible = "ti,twl4030-vpll2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vmmc1: regulator@2 { + compatible = "ti,twl4030-vmmc1"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; + }; + + twl_gpio: gpio { + compatible = "ti,twl4030-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; +}; diff --git a/arch/arm/boot/dts/twl6030.dtsi b/arch/arm/boot/dts/twl6030.dtsi new file mode 100644 index 000000000000..3b2f3510d7eb --- /dev/null +++ b/arch/arm/boot/dts/twl6030.dtsi @@ -0,0 +1,86 @@ +/* + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Integrated Power Management Chip + * http://www.ti.com/lit/ds/symlink/twl6030.pdf + */ +&twl { + compatible = "ti,twl6030"; + interrupt-controller; + #interrupt-cells = <1>; + + rtc { + compatible = "ti,twl4030-rtc"; + interrupts = <11>; + }; + + vaux1: regulator@0 { + compatible = "ti,twl6030-vaux1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; + + vaux2: regulator@1 { + compatible = "ti,twl6030-vaux2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2800000>; + }; + + vaux3: regulator@2 { + compatible = "ti,twl6030-vaux3"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + }; + + vmmc: regulator@3 { + compatible = "ti,twl6030-vmmc"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + }; + + vpp: regulator@4 { + compatible = "ti,twl6030-vpp"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2500000>; + }; + + vusim: regulator@5 { + compatible = "ti,twl6030-vusim"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2900000>; + }; + + vdac: regulator@6 { + compatible = "ti,twl6030-vdac"; + }; + + vana: regulator@7 { + compatible = "ti,twl6030-vana"; + }; + + vcxio: regulator@8 { + compatible = "ti,twl6030-vcxio"; + }; + + vusb: regulator@9 { + compatible = "ti,twl6030-vusb"; + }; + + v1v8: regulator@10 { + compatible = "ti,twl6030-v1v8"; + }; + + v2v1: regulator@11 { + compatible = "ti,twl6030-v2v1"; + }; + + clk32kg: regulator@12 { + compatible = "ti,twl6030-clk32kg"; + }; +}; diff --git a/arch/arm/boot/dts/usb_a9260.dts b/arch/arm/boot/dts/usb_a9260.dts new file mode 100644 index 000000000000..296216058c11 --- /dev/null +++ b/arch/arm/boot/dts/usb_a9260.dts @@ -0,0 +1,23 @@ +/* + * usb_a9260.dts - Device Tree file for Caloa USB A9260 board + * + * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 or later. + */ +/dts-v1/; +/include/ "at91sam9260.dtsi" +/include/ "usb_a9260_common.dtsi" + +/ { + model = "Calao USB A9260"; + compatible = "calao,usb-a9260", "atmel,at91sam9260", "atmel,at91sam9"; + + chosen { + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; +}; diff --git a/arch/arm/boot/dts/usb_a9260_common.dtsi b/arch/arm/boot/dts/usb_a9260_common.dtsi new file mode 100644 index 000000000000..e70d229baef5 --- /dev/null +++ b/arch/arm/boot/dts/usb_a9260_common.dtsi @@ -0,0 +1,117 @@ +/* + * usb_a926x.dts - Device Tree file for Caloa USB A926x board + * + * Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 or later. + */ + +/ { + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + + macb0: ethernet@fffc4000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fffa4000 { + atmel,vbus-gpio = <&pioC 5 0>; + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + oftree@80000 { + label = "oftree"; + reg = <0xa0000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xc0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4c0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7cc0000 0x8340000>; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + user_led { + label = "user_led"; + gpios = <&pioB 21 1>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + user_pb { + label = "user_pb"; + gpios = <&pioB 10 1>; + linux,code = <28>; + gpio-key,wakeup; + }; + }; + + i2c@0 { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/usb_a9263.dts b/arch/arm/boot/dts/usb_a9263.dts new file mode 100644 index 000000000000..6fe05ccb6203 --- /dev/null +++ b/arch/arm/boot/dts/usb_a9263.dts @@ -0,0 +1,131 @@ +/* + * usb_a9263.dts - Device Tree file for Caloa USB A9293 board + * + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2 only + */ +/dts-v1/; +/include/ "at91sam9263.dtsi" + +/ { + model = "Calao USB A9263"; + compatible = "atmel,usb-a9263", "atmel,at91sam9263", "atmel,at91sam9"; + + chosen { + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; + }; + + memory { + reg = <0x20000000 0x4000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + dbgu: serial@ffffee00 { + status = "okay"; + }; + + macb0: ethernet@fffbc000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fff78000 { + atmel,vbus-gpio = <&pioB 11 0>; + status = "okay"; + }; + + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + oftree@80000 { + label = "oftree"; + reg = <0xa0000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xc0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4c0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7cc0000 0x8340000>; + }; + }; + + usb0: ohci@00a00000 { + num-ports = <2>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + user_led { + label = "user_led"; + gpios = <&pioB 21 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + user_pb { + label = "user_pb"; + gpios = <&pioB 10 1>; + linux,code = <28>; + gpio-key,wakeup; + }; + }; + + i2c@0 { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/usb_a9g20.dts b/arch/arm/boot/dts/usb_a9g20.dts index 7c2399c532e5..2dacb16ce4ae 100644 --- a/arch/arm/boot/dts/usb_a9g20.dts +++ b/arch/arm/boot/dts/usb_a9g20.dts @@ -7,6 +7,7 @@ */ /dts-v1/; /include/ "at91sam9g20.dtsi" +/include/ "usb_a9260_common.dtsi" / { model = "Calao USB A9G20"; @@ -20,108 +21,7 @@ reg = <0x20000000 0x4000000>; }; - clocks { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - main_clock: clock@0 { - compatible = "atmel,osc", "fixed-clock"; - clock-frequency = <12000000>; - }; - }; - - ahb { - apb { - dbgu: serial@fffff200 { - status = "okay"; - }; - - macb0: ethernet@fffc4000 { - phy-mode = "rmii"; - status = "okay"; - }; - - usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; - status = "okay"; - }; - }; - - nand0: nand@40000000 { - nand-bus-width = <8>; - nand-ecc-mode = "soft"; - nand-on-flash-bbt; - status = "okay"; - - at91bootstrap@0 { - label = "at91bootstrap"; - reg = <0x0 0x20000>; - }; - - barebox@20000 { - label = "barebox"; - reg = <0x20000 0x40000>; - }; - - bareboxenv@60000 { - label = "bareboxenv"; - reg = <0x60000 0x20000>; - }; - - bareboxenv2@80000 { - label = "bareboxenv2"; - reg = <0x80000 0x20000>; - }; - - kernel@a0000 { - label = "kernel"; - reg = <0xa0000 0x400000>; - }; - - rootfs@4a0000 { - label = "rootfs"; - reg = <0x4a0000 0x7800000>; - }; - - data@7ca0000 { - label = "data"; - reg = <0x7ca0000 0x8360000>; - }; - }; - - usb0: ohci@00500000 { - num-ports = <2>; - status = "okay"; - }; - }; - - leds { - compatible = "gpio-leds"; - - user_led { - label = "user_led"; - gpios = <&pioB 21 1>; - linux,default-trigger = "heartbeat"; - }; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - - user_pb { - label = "user_pb"; - gpios = <&pioB 10 1>; - linux,code = <28>; - gpio-key,wakeup; - }; - }; - i2c@0 { - status = "okay"; - rv3029c2@56 { compatible = "rv3029c2"; reg = <0x56>; |