diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/acpi/enumeration.txt | 2 | ||||
| -rw-r--r-- | Documentation/cpu-freq/intel-pstate.txt | 8 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt | 110 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/pci/versatile.txt | 59 | ||||
| -rw-r--r-- | Documentation/filesystems/xfs.txt | 22 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 3 | ||||
| -rw-r--r-- | Documentation/power/s2ram.txt | 4 |
7 files changed, 195 insertions, 13 deletions
diff --git a/Documentation/acpi/enumeration.txt b/Documentation/acpi/enumeration.txt index b60d2ab69497..9b121a569ab4 100644 --- a/Documentation/acpi/enumeration.txt +++ b/Documentation/acpi/enumeration.txt @@ -243,7 +243,7 @@ input driver: .owner = THIS_MODULE, .pm = &mpu3050_pm, .of_match_table = mpu3050_of_match, - .acpi_match_table ACPI_PTR(mpu3050_acpi_match), + .acpi_match_table = ACPI_PTR(mpu3050_acpi_match), }, .probe = mpu3050_probe, .remove = mpu3050_remove, diff --git a/Documentation/cpu-freq/intel-pstate.txt b/Documentation/cpu-freq/intel-pstate.txt index 765d7fc0e692..655750743fb0 100644 --- a/Documentation/cpu-freq/intel-pstate.txt +++ b/Documentation/cpu-freq/intel-pstate.txt @@ -37,6 +37,14 @@ controlling P state selection. These files have been added to no_turbo: limits the driver to selecting P states below the turbo frequency range. + turbo_pct: displays the percentage of the total performance that + is supported by hardware that is in the turbo range. This number + is independent of whether turbo has been disabled or not. + + num_pstates: displays the number of pstates that are supported + by hardware. This number is independent of whether turbo has + been disabled or not. + For contemporary Intel processors, the frequency is controlled by the processor itself and the P-states exposed to software are related to performance levels. The idea that frequency can be set to a single diff --git a/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt new file mode 100644 index 000000000000..b54bf3a2ff57 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt @@ -0,0 +1,110 @@ + +* Samsung Exynos PPMU (Platform Performance Monitoring Unit) device + +The Samsung Exynos SoC has PPMU (Platform Performance Monitoring Unit) for +each IP. PPMU provides the primitive values to get performance data. These +PPMU events provide information of the SoC's behaviors so that you may +use to analyze system performance, to make behaviors visible and to count +usages of each IP (DMC, CPU, RIGHTBUS, LEFTBUS, CAM interface, LCD, G3D, MFC). +The Exynos PPMU driver uses the devfreq-event class to provide event data +to various devfreq devices. The devfreq devices would use the event data when +derterming the current state of each IP. + +Required properties: +- compatible: Should be "samsung,exynos-ppmu". +- reg: physical base address of each PPMU and length of memory mapped region. + +Optional properties: +- clock-names : the name of clock used by the PPMU, "ppmu" +- clocks : phandles for clock specified in "clock-names" property +- #clock-cells: should be 1. + +Example1 : PPMU nodes in exynos3250.dtsi are listed below. + + ppmu_dmc0: ppmu_dmc0@106a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106a0000 0x2000>; + status = "disabled"; + }; + + ppmu_dmc1: ppmu_dmc1@106b0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106b0000 0x2000>; + status = "disabled"; + }; + + ppmu_cpu: ppmu_cpu@106c0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106c0000 0x2000>; + status = "disabled"; + }; + + ppmu_rightbus: ppmu_rightbus@112a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x112a0000 0x2000>; + clocks = <&cmu CLK_PPMURIGHT>; + clock-names = "ppmu"; + status = "disabled"; + }; + + ppmu_leftbus: ppmu_leftbus0@116a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x116a0000 0x2000>; + clocks = <&cmu CLK_PPMULEFT>; + clock-names = "ppmu"; + status = "disabled"; + }; + +Example2 : Events of each PPMU node in exynos3250-rinato.dts are listed below. + + &ppmu_dmc0 { + status = "okay"; + + events { + ppmu_dmc0_3: ppmu-event3-dmc0 { + event-name = "ppmu-event3-dmc0"; + }; + + ppmu_dmc0_2: ppmu-event2-dmc0 { + event-name = "ppmu-event2-dmc0"; + }; + + ppmu_dmc0_1: ppmu-event1-dmc0 { + event-name = "ppmu-event1-dmc0"; + }; + + ppmu_dmc0_0: ppmu-event0-dmc0 { + event-name = "ppmu-event0-dmc0"; + }; + }; + }; + + &ppmu_dmc1 { + status = "okay"; + + events { + ppmu_dmc1_3: ppmu-event3-dmc1 { + event-name = "ppmu-event3-dmc1"; + }; + }; + }; + + &ppmu_leftbus { + status = "okay"; + + events { + ppmu_leftbus_3: ppmu-event3-leftbus { + event-name = "ppmu-event3-leftbus"; + }; + }; + }; + + &ppmu_rightbus { + status = "okay"; + + events { + ppmu_rightbus_3: ppmu-event3-rightbus { + event-name = "ppmu-event3-rightbus"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/versatile.txt b/Documentation/devicetree/bindings/pci/versatile.txt new file mode 100644 index 000000000000..ebd1e7d0403e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/versatile.txt @@ -0,0 +1,59 @@ +* ARM Versatile Platform Baseboard PCI interface + +PCI host controller found on the ARM Versatile PB board's FPGA. + +Required properties: +- compatible: should contain "arm,versatile-pci" to identify the Versatile PCI + controller. +- reg: base addresses and lengths of the pci controller. There must be 3 + entries: + - Versatile-specific registers + - Self Config space + - Config space +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- bus-range: set to <0 0xff> +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties to define + the mapping of the PCI interface to interrupt numbers. + +Example: + +pci-controller@10001000 { + compatible = "arm,versatile-pci"; + device_type = "pci"; + reg = <0x10001000 0x1000 + 0x41000000 0x10000 + 0x42000000 0x100000>; + bus-range = <0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + ranges = <0x01000000 0 0x00000000 0x43000000 0 0x00010000 /* downstream I/O */ + 0x02000000 0 0x50000000 0x50000000 0 0x10000000 /* non-prefetchable memory */ + 0x42000000 0 0x60000000 0x60000000 0 0x10000000>; /* prefetchable memory */ + + interrupt-map-mask = <0x1800 0 0 7>; + interrupt-map = <0x1800 0 0 1 &sic 28 + 0x1800 0 0 2 &sic 29 + 0x1800 0 0 3 &sic 30 + 0x1800 0 0 4 &sic 27 + + 0x1000 0 0 1 &sic 27 + 0x1000 0 0 2 &sic 28 + 0x1000 0 0 3 &sic 29 + 0x1000 0 0 4 &sic 30 + + 0x0800 0 0 1 &sic 30 + 0x0800 0 0 2 &sic 27 + 0x0800 0 0 3 &sic 28 + 0x0800 0 0 4 &sic 29 + + 0x0000 0 0 1 &sic 29 + 0x0000 0 0 2 &sic 30 + 0x0000 0 0 3 &sic 27 + 0x0000 0 0 4 &sic 28>; +}; diff --git a/Documentation/filesystems/xfs.txt b/Documentation/filesystems/xfs.txt index 5be51fd888bd..0bfafe108357 100644 --- a/Documentation/filesystems/xfs.txt +++ b/Documentation/filesystems/xfs.txt @@ -287,9 +287,9 @@ The following sysctls are available for the XFS filesystem: XFS_ERRLEVEL_LOW: 1 XFS_ERRLEVEL_HIGH: 5 - fs.xfs.panic_mask (Min: 0 Default: 0 Max: 127) + fs.xfs.panic_mask (Min: 0 Default: 0 Max: 255) Causes certain error conditions to call BUG(). Value is a bitmask; - AND together the tags which represent errors which should cause panics: + OR together the tags which represent errors which should cause panics: XFS_NO_PTAG 0 XFS_PTAG_IFLUSH 0x00000001 @@ -299,6 +299,7 @@ The following sysctls are available for the XFS filesystem: XFS_PTAG_SHUTDOWN_CORRUPT 0x00000010 XFS_PTAG_SHUTDOWN_IOERROR 0x00000020 XFS_PTAG_SHUTDOWN_LOGERROR 0x00000040 + XFS_PTAG_FSBLOCK_ZERO 0x00000080 This option is intended for debugging only. @@ -348,16 +349,13 @@ The following sysctls are available for the XFS filesystem: Deprecated Sysctls ================== - fs.xfs.xfsbufd_centisecs (Min: 50 Default: 100 Max: 3000) - Dirty metadata is now tracked by the log subsystem and - flushing is driven by log space and idling demands. The - xfsbufd no longer exists, so this syctl does nothing. +None at present. - Due for removal in 3.14. - fs.xfs.age_buffer_centisecs (Min: 100 Default: 1500 Max: 720000) - Dirty metadata is now tracked by the log subsystem and - flushing is driven by log space and idling demands. The - xfsbufd no longer exists, so this syctl does nothing. +Removed Sysctls +=============== - Due for removal in 3.14. + Name Removed + ---- ------- + fs.xfs.xfsbufd_centisec v3.20 + fs.xfs.age_buffer_centisecs v3.20 diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 176d4fe4f076..f06f1f609cb7 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1470,6 +1470,9 @@ bytes respectively. Such letter suffixes can also be entirely omitted. no_hwp Do not enable hardware P state control (HWP) if available. + hwp_only + Only load intel_pstate on systems which support + hardware P state control (HWP) if available. intremap= [X86-64, Intel-IOMMU] on enable Interrupt Remapping (default) diff --git a/Documentation/power/s2ram.txt b/Documentation/power/s2ram.txt index 1bdfa0443773..4685aee197fd 100644 --- a/Documentation/power/s2ram.txt +++ b/Documentation/power/s2ram.txt @@ -69,6 +69,10 @@ Reason for this is that the RTC is the only reliably available piece of hardware during resume operations where a value can be set that will survive a reboot. +pm_trace is not compatible with asynchronous suspend, so it turns +asynchronous suspend off (which may work around timing or +ordering-sensitive bugs). + Consequence is that after a resume (even if it is successful) your system clock will have a value corresponding to the magic number instead of the correct date/time! It is therefore advisable to use a program like ntp-date |