diff options
Diffstat (limited to 'Documentation/power')
| -rw-r--r-- | Documentation/power/00-INDEX | 4 | ||||
| -rw-r--r-- | Documentation/power/apm-acpi.txt | 32 | ||||
| -rw-r--r-- | Documentation/power/pm.txt | 257 | ||||
| -rw-r--r-- | Documentation/power/pm_qos_interface.txt | 7 | ||||
| -rw-r--r-- | Documentation/power/power_supply_class.txt | 4 | ||||
| -rw-r--r-- | Documentation/power/regulator/consumer.txt | 182 | ||||
| -rw-r--r-- | Documentation/power/regulator/machine.txt | 101 | ||||
| -rw-r--r-- | Documentation/power/regulator/overview.txt | 171 | ||||
| -rw-r--r-- | Documentation/power/regulator/regulator.txt | 30 |
9 files changed, 528 insertions, 260 deletions
diff --git a/Documentation/power/00-INDEX b/Documentation/power/00-INDEX index a55d7f1c836d..fb742c213c9e 100644 --- a/Documentation/power/00-INDEX +++ b/Documentation/power/00-INDEX @@ -1,5 +1,7 @@ 00-INDEX - This file +apm-acpi.txt + - basic info about the APM and ACPI support. basic-pm-debugging.txt - Debugging suspend and resume devices.txt @@ -14,8 +16,6 @@ notifiers.txt - Registering suspend notifiers in device drivers pci.txt - How the PCI Subsystem Does Power Management -pm.txt - - info on Linux power management support. pm_qos_interface.txt - info on Linux PM Quality of Service interface power_supply_class.txt diff --git a/Documentation/power/apm-acpi.txt b/Documentation/power/apm-acpi.txt new file mode 100644 index 000000000000..1bd799dc17e8 --- /dev/null +++ b/Documentation/power/apm-acpi.txt @@ -0,0 +1,32 @@ +APM or ACPI? +------------ +If you have a relatively recent x86 mobile, desktop, or server system, +odds are it supports either Advanced Power Management (APM) or +Advanced Configuration and Power Interface (ACPI). ACPI is the newer +of the two technologies and puts power management in the hands of the +operating system, allowing for more intelligent power management than +is possible with BIOS controlled APM. + +The best way to determine which, if either, your system supports is to +build a kernel with both ACPI and APM enabled (as of 2.3.x ACPI is +enabled by default). If a working ACPI implementation is found, the +ACPI driver will override and disable APM, otherwise the APM driver +will be used. + +No, sorry, you cannot have both ACPI and APM enabled and running at +once. Some people with broken ACPI or broken APM implementations +would like to use both to get a full set of working features, but you +simply cannot mix and match the two. Only one power management +interface can be in control of the machine at once. Think about it.. + +User-space Daemons +------------------ +Both APM and ACPI rely on user-space daemons, apmd and acpid +respectively, to be completely functional. Obtain both of these +daemons from your Linux distribution or from the Internet (see below) +and be sure that they are started sometime in the system boot process. +Go ahead and start both. If ACPI or APM is not available on your +system the associated daemon will exit gracefully. + + apmd: http://worldvisions.ca/~apenwarr/apmd/ + acpid: http://acpid.sf.net/ diff --git a/Documentation/power/pm.txt b/Documentation/power/pm.txt deleted file mode 100644 index be841507e43f..000000000000 --- a/Documentation/power/pm.txt +++ /dev/null @@ -1,257 +0,0 @@ - Linux Power Management Support - -This document briefly describes how to use power management with your -Linux system and how to add power management support to Linux drivers. - -APM or ACPI? ------------- -If you have a relatively recent x86 mobile, desktop, or server system, -odds are it supports either Advanced Power Management (APM) or -Advanced Configuration and Power Interface (ACPI). ACPI is the newer -of the two technologies and puts power management in the hands of the -operating system, allowing for more intelligent power management than -is possible with BIOS controlled APM. - -The best way to determine which, if either, your system supports is to -build a kernel with both ACPI and APM enabled (as of 2.3.x ACPI is -enabled by default). If a working ACPI implementation is found, the -ACPI driver will override and disable APM, otherwise the APM driver -will be used. - -No, sorry, you cannot have both ACPI and APM enabled and running at -once. Some people with broken ACPI or broken APM implementations -would like to use both to get a full set of working features, but you -simply cannot mix and match the two. Only one power management -interface can be in control of the machine at once. Think about it.. - -User-space Daemons ------------------- -Both APM and ACPI rely on user-space daemons, apmd and acpid -respectively, to be completely functional. Obtain both of these -daemons from your Linux distribution or from the Internet (see below) -and be sure that they are started sometime in the system boot process. -Go ahead and start both. If ACPI or APM is not available on your -system the associated daemon will exit gracefully. - - apmd: http://worldvisions.ca/~apenwarr/apmd/ - acpid: http://acpid.sf.net/ - -Driver Interface -- OBSOLETE, DO NOT USE! -----------------************************* - -Note: pm_register(), pm_access(), pm_dev_idle() and friends are -obsolete. Please do not use them. Instead you should properly hook -your driver into the driver model, and use its suspend()/resume() -callbacks to do this kind of stuff. - -If you are writing a new driver or maintaining an old driver, it -should include power management support. Without power management -support, a single driver may prevent a system with power management -capabilities from ever being able to suspend (safely). - -Overview: -1) Register each instance of a device with "pm_register" -2) Call "pm_access" before accessing the hardware. - (this will ensure that the hardware is awake and ready) -3) Your "pm_callback" is called before going into a - suspend state (ACPI D1-D3) or after resuming (ACPI D0) - from a suspend. -4) Call "pm_dev_idle" when the device is not being used - (optional but will improve device idle detection) -5) When unloaded, unregister the device with "pm_unregister" - -/* - * Description: Register a device with the power-management subsystem - * - * Parameters: - * type - device type (PCI device, system device, ...) - * id - instance number or unique identifier - * cback - request handler callback (suspend, resume, ...) - * - * Returns: Registered PM device or NULL on error - * - * Examples: - * dev = pm_register(PM_SYS_DEV, PM_SYS_VGA, vga_callback); - * - * struct pci_dev *pci_dev = pci_find_dev(...); - * dev = pm_register(PM_PCI_DEV, PM_PCI_ID(pci_dev), callback); - */ -struct pm_dev *pm_register(pm_dev_t type, unsigned long id, pm_callback cback); - -/* - * Description: Unregister a device with the power management subsystem - * - * Parameters: - * dev - PM device previously returned from pm_register - */ -void pm_unregister(struct pm_dev *dev); - -/* - * Description: Unregister all devices with a matching callback function - * - * Parameters: - * cback - previously registered request callback - * - * Notes: Provided for easier porting from old APM interface - */ -void pm_unregister_all(pm_callback cback); - -/* - * Power management request callback - * - * Parameters: - * dev - PM device previously returned from pm_register - * rqst - request type - * data - data, if any, associated with the request - * - * Returns: 0 if the request is successful - * EINVAL if the request is not supported - * EBUSY if the device is now busy and cannot handle the request - * ENOMEM if the device was unable to handle the request due to memory - * - * Details: The device request callback will be called before the - * device/system enters a suspend state (ACPI D1-D3) or - * or after the device/system resumes from suspend (ACPI D0). - * For PM_SUSPEND, the ACPI D-state being entered is passed - * as the "data" argument to the callback. The device - * driver should save (PM_SUSPEND) or restore (PM_RESUME) - * device context when the request callback is called. - * - * Once a driver returns 0 (success) from a suspend - * request, it should not process any further requests or - * access the device hardware until a call to "pm_access" is made. - */ -typedef int (*pm_callback)(struct pm_dev *dev, pm_request_t rqst, void *data); - -Driver Details --------------- -This is just a quick Q&A as a stopgap until a real driver writers' -power management guide is available. - -Q: When is a device suspended? - -Devices can be suspended based on direct user request (eg. laptop lid -closes), system power policy (eg. sleep after 30 minutes of console -inactivity), or device power policy (eg. power down device after 5 -minutes of inactivity) - -Q: Must a driver honor a suspend request? - -No, a driver can return -EBUSY from a suspend request and this -will stop the system from suspending. When a suspend request -fails, all suspended devices are resumed and the system continues -to run. Suspend can be retried at a later time. - -Q: Can the driver block suspend/resume requests? - -Yes, a driver can delay its return from a suspend or resume -request until the device is ready to handle requests. It -is advantageous to return as quickly as possible from a -request as suspend/resume are done serially. - -Q: What context is a suspend/resume initiated from? - -A suspend or resume is initiated from a kernel thread context. -It is safe to block, allocate memory, initiate requests -or anything else you can do within the kernel. - -Q: Will requests continue to arrive after a suspend? - -Possibly. It is the driver's responsibility to queue(*), -fail, or drop any requests that arrive after returning -success to a suspend request. It is important that the -driver not access its device until after it receives -a resume request as the device's bus may no longer -be active. - -(*) If a driver queues requests for processing after - resume be aware that the device, network, etc. - might be in a different state than at suspend time. - It's probably better to drop requests unless - the driver is a storage device. - -Q: Do I have to manage bus-specific power management registers - -No. It is the responsibility of the bus driver to manage -PCI, USB, etc. power management registers. The bus driver -or the power management subsystem will also enable any -wake-on functionality that the device has. - -Q: So, really, what do I need to do to support suspend/resume? - -You need to save any device context that would -be lost if the device was powered off and then restore -it at resume time. When ACPI is active, there are -three levels of device suspend states; D1, D2, and D3. -(The suspend state is passed as the "data" argument -to the device callback.) With D3, the device is powered -off and loses all context, D1 and D2 are shallower power -states and require less device context to be saved. To -play it safe, just save everything at suspend and restore -everything at resume. - -Q: Where do I store device context for suspend? - -Anywhere in memory, kmalloc a buffer or store it -in the device descriptor. You are guaranteed that the -contents of memory will be restored and accessible -before resume, even when the system suspends to disk. - -Q: What do I need to do for ACPI vs. APM vs. etc? - -Drivers need not be aware of the specific power management -technology that is active. They just need to be aware -of when the overlying power management system requests -that they suspend or resume. - -Q: What about device dependencies? - -When a driver registers a device, the power management -subsystem uses the information provided to build a -tree of device dependencies (eg. USB device X is on -USB controller Y which is on PCI bus Z) When power -management wants to suspend a device, it first sends -a suspend request to its driver, then the bus driver, -and so on up to the system bus. Device resumes -proceed in the opposite direction. - -Q: Who do I contact for additional information about - enabling power management for my specific driver/device? - -ACPI Development mailing list: linux-acpi@vger.kernel.org - -System Interface -- OBSOLETE, DO NOT USE! -----------------************************* -If you are providing new power management support to Linux (ie. -adding support for something like APM or ACPI), you should -communicate with drivers through the existing generic power -management interface. - -/* - * Send a request to all devices - * - * Parameters: - * rqst - request type - * data - data, if any, associated with the request - * - * Returns: 0 if the request is successful - * See "pm_callback" return for errors - * - * Details: Walk list of registered devices and call pm_send - * for each until complete or an error is encountered. - * If an error is encountered for a suspend request, - * return all devices to the state they were in before - * the suspend request. - */ -int pm_send_all(pm_request_t rqst, void *data); - -/* - * Find a matching device - * - * Parameters: - * type - device type (PCI device, system device, or 0 to match all devices) - * from - previous match or NULL to start from the beginning - * - * Returns: Matching device or NULL if none found - */ -struct pm_dev *pm_find(pm_dev_t type, struct pm_dev *from); diff --git a/Documentation/power/pm_qos_interface.txt b/Documentation/power/pm_qos_interface.txt index 49adb1a33514..c40866e8b957 100644 --- a/Documentation/power/pm_qos_interface.txt +++ b/Documentation/power/pm_qos_interface.txt @@ -1,4 +1,4 @@ -PM quality of Service interface. +PM Quality Of Service Interface. This interface provides a kernel and user mode interface for registering performance expectations by drivers, subsystems and user space applications on @@ -7,6 +7,11 @@ one of the parameters. Currently we have {cpu_dma_latency, network_latency, network_throughput} as the initial set of pm_qos parameters. +Each parameters have defined units: + * latency: usec + * timeout: usec + * throughput: kbs (kilo bit / sec) + The infrastructure exposes multiple misc device nodes one per implemented parameter. The set of parameters implement is defined by pm_qos_power_init() and pm_qos_params.h. This is done because having the available parameters diff --git a/Documentation/power/power_supply_class.txt b/Documentation/power/power_supply_class.txt index a8686e5a6857..c6cd4956047c 100644 --- a/Documentation/power/power_supply_class.txt +++ b/Documentation/power/power_supply_class.txt @@ -101,6 +101,10 @@ of charge when battery became full/empty". It also could mean "value of charge when battery considered full/empty at given conditions (temperature, age)". I.e. these attributes represents real thresholds, not design values. +CHARGE_COUNTER - the current charge counter (in µAh). This could easily +be negative; there is no empty or full value. It is only useful for +relative, time-based measurements. + ENERGY_FULL, ENERGY_EMPTY - same as above but for energy. CAPACITY - capacity in percents. diff --git a/Documentation/power/regulator/consumer.txt b/Documentation/power/regulator/consumer.txt new file mode 100644 index 000000000000..82b7a43aadba --- /dev/null +++ b/Documentation/power/regulator/consumer.txt @@ -0,0 +1,182 @@ +Regulator Consumer Driver Interface +=================================== + +This text describes the regulator interface for consumer device drivers. +Please see overview.txt for a description of the terms used in this text. + + +1. Consumer Regulator Access (static & dynamic drivers) +======================================================= + +A consumer driver can get access to it's supply regulator by calling :- + +regulator = regulator_get(dev, "Vcc"); + +The consumer passes in it's struct device pointer and power supply ID. The core +then finds the correct regulator by consulting a machine specific lookup table. +If the lookup is successful then this call will return a pointer to the struct +regulator that supplies this consumer. + +To release the regulator the consumer driver should call :- + +regulator_put(regulator); + +Consumers can be supplied by more than one regulator e.g. codec consumer with +analog and digital supplies :- + +digital = regulator_get(dev, "Vcc"); /* digital core */ +analog = regulator_get(dev, "Avdd"); /* analog */ + +The regulator access functions regulator_get() and regulator_put() will +usually be called in your device drivers probe() and remove() respectively. + + +2. Regulator Output Enable & Disable (static & dynamic drivers) +==================================================================== + +A consumer can enable it's power supply by calling:- + +int regulator_enable(regulator); + +NOTE: The supply may already be enabled before regulator_enabled() is called. +This may happen if the consumer shares the regulator or the regulator has been +previously enabled by bootloader or kernel board initialization code. + +A consumer can determine if a regulator is enabled by calling :- + +int regulator_is_enabled(regulator); + +This will return > zero when the regulator is enabled. + + +A consumer can disable it's supply when no longer needed by calling :- + +int regulator_disable(regulator); + +NOTE: This may not disable the supply if it's shared with other consumers. The +regulator will only be disabled when the enabled reference count is zero. + +Finally, a regulator can be forcefully disabled in the case of an emergency :- + +int regulator_force_disable(regulator); + +NOTE: this will immediately and forcefully shutdown the regulator output. All +consumers will be powered off. + + +3. Regulator Voltage Control & Status (dynamic drivers) +====================================================== + +Some consumer drivers need to be able to dynamically change their supply +voltage to match system operating points. e.g. CPUfreq drivers can scale +voltage along with frequency to save power, SD drivers may need to select the +correct card voltage, etc. + +Consumers can control their supply voltage by calling :- + +int regulator_set_voltage(regulator, min_uV, max_uV); + +Where min_uV and max_uV are the minimum and maximum acceptable voltages in +microvolts. + +NOTE: this can be called when the regulator is enabled or disabled. If called +when enabled, then the voltage changes instantly, otherwise the voltage +configuration changes and the voltage is physically set when the regulator is +next enabled. + +The regulators configured voltage output can be found by calling :- + +int regulator_get_voltage(regulator); + +NOTE: get_voltage() will return the configured output voltage whether the +regulator is enabled or disabled and should NOT be used to determine regulator +output state. However this can be used in conjunction with is_enabled() to +determine the regulator physical output voltage. + + +4. Regulator Current Limit Control & Status (dynamic drivers) +=========================================================== + +Some consumer drivers need to be able to dynamically change their supply +current limit to match system operating points. e.g. LCD backlight driver can +change the current limit to vary the backlight brightness, USB drivers may want +to set the limit to 500mA when supplying power. + +Consumers can control their supply current limit by calling :- + +int regulator_set_current_limit(regulator, min_uV, max_uV); + +Where min_uA and max_uA are the minimum and maximum acceptable current limit in +microamps. + +NOTE: this can be called when the regulator is enabled or disabled. If called +when enabled, then the current limit changes instantly, otherwise the current +limit configuration changes and the current limit is physically set when the +regulator is next enabled. + +A regulators current limit can be found by calling :- + +int regulator_get_current_limit(regulator); + +NOTE: get_current_limit() will return the current limit whether the regulator +is enabled or disabled and should not be used to determine regulator current +load. + + +5. Regulator Operating Mode Control & Status (dynamic drivers) +============================================================= + +Some consumers can further save system power by changing the operating mode of +their supply regulator to be more efficient when the consumers operating state +changes. e.g. consumer driver is idle and subsequently draws less current + +Regulator operating mode can be changed indirectly or directly. + +Indirect operating mode control. +-------------------------------- +Consumer drivers can request a change in their supply regulator operating mode +by calling :- + +int regulator_set_optimum_mode(struct regulator *regulator, int load_uA); + +This will cause the core to recalculate the total load on the regulator (based +on all it's consumers) and change operating mode (if necessary and permitted) +to best match the current operating load. + +The load_uA value can be determined from the consumers datasheet. e.g.most +datasheets have tables showing the max current consumed in certain situations. + +Most consumers will use indirect operating mode control since they have no +knowledge of the regulator or whether the regulator is shared with other +consumers. + +Direct operating mode control. +------------------------------ +Bespoke or tightly coupled drivers may want to directly control regulator +operating mode depending on their operating point. This can be achieved by +calling :- + +int regulator_set_mode(struct regulator *regulator, unsigned int mode); +unsigned int regulator_get_mode(struct regulator *regulator); + +Direct mode will only be used by consumers that *know* about the regulator and +are not sharing the regulator with other consumers. + + +6. Regulator Events +=================== +Regulators can notify consumers of external events. Events could be received by +consumers under regulator stress or failure conditions. + +Consumers can register interest in regulator events by calling :- + +int regulator_register_notifier(struct regulator *regulator, + struct notifier_block *nb); + +Consumers can uregister interest by calling :- + +int regulator_unregister_notifier(struct regulator *regulator, + struct notifier_block *nb); + +Regulators use the kernel notifier framework to send event to thier interested +consumers. diff --git a/Documentation/power/regulator/machine.txt b/Documentation/power/regulator/machine.txt new file mode 100644 index 000000000000..c9a35665cf70 --- /dev/null +++ b/Documentation/power/regulator/machine.txt @@ -0,0 +1,101 @@ +Regulator Machine Driver Interface +=================================== + +The regulator machine driver interface is intended for board/machine specific +initialisation code to configure the regulator subsystem. Typical things that +machine drivers would do are :- + + 1. Regulator -> Device mapping. + 2. Regulator supply configuration. + 3. Power Domain constraint setting. + + + +1. Regulator -> device mapping +============================== +Consider the following machine :- + + Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V] + | + +-> [Consumer B @ 3.3V] + +The drivers for consumers A & B must be mapped to the correct regulator in +order to control their power supply. This mapping can be achieved in machine +initialisation code by calling :- + +int regulator_set_device_supply(const char *regulator, struct device *dev, + const char *supply); + +and is shown with the following code :- + +regulator_set_device_supply("Regulator-1", devB, "Vcc"); +regulator_set_device_supply("Regulator-2", devA, "Vcc"); + +This maps Regulator-1 to the 'Vcc' supply for Consumer B and maps Regulator-2 +to the 'Vcc' supply for Consumer A. + + +2. Regulator supply configuration. +================================== +Consider the following machine (again) :- + + Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V] + | + +-> [Consumer B @ 3.3V] + +Regulator-1 supplies power to Regulator-2. This relationship must be registered +with the core so that Regulator-1 is also enabled when Consumer A enables it's +supply (Regulator-2). + +This relationship can be register with the core via :- + +int regulator_set_supply(const char *regulator, const char *regulator_supply); + +In this example we would use the following code :- + +regulator_set_supply("Regulator-2", "Regulator-1"); + +Relationships can be queried by calling :- + +const char *regulator_get_supply(const char *regulator); + + +3. Power Domain constraint setting. +=================================== +Each power domain within a system has physical constraints on voltage and +current. This must be defined in software so that the power domain is always +operated within specifications. + +Consider the following machine (again) :- + + Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V] + | + +-> [Consumer B @ 3.3V] + +This gives us two regulators and two power domains: + + Domain 1: Regulator-2, Consumer B. + Domain 2: Consumer A. + +Constraints can be registered by calling :- + +int regulator_set_platform_constraints(const char *regulator, + struct regulation_constraints *constraints); + +The example is defined as follows :- + +struct regulation_constraints domain_1 = { + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, +}; + +struct regulation_constraints domain_2 = { + .min_uV = 1800000, + .max_uV = 2000000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, + .valid_modes_mask = REGULATOR_MODE_NORMAL, +}; + +regulator_set_platform_constraints("Regulator-1", &domain_1); +regulator_set_platform_constraints("Regulator-2", &domain_2); diff --git a/Documentation/power/regulator/overview.txt b/Documentation/power/regulator/overview.txt new file mode 100644 index 000000000000..bdcb332bd7fb --- /dev/null +++ b/Documentation/power/regulator/overview.txt @@ -0,0 +1,171 @@ +Linux voltage and current regulator framework +============================================= + +About +===== + +This framework is designed to provide a standard kernel interface to control +voltage and current regulators. + +The intention is to allow systems to dynamically control regulator power output +in order to save power and prolong battery life. This applies to both voltage +regulators (where voltage output is controllable) and current sinks (where +current limit is controllable). + +(C) 2008 Wolfson Microelectronics PLC. +Author: Liam Girdwood <lg@opensource.wolfsonmicro.com> + + +Nomenclature +============ + +Some terms used in this document:- + + o Regulator - Electronic device that supplies power to other devices. + Most regulators can enable and disable their output whilst + some can control their output voltage and or current. + + Input Voltage -> Regulator -> Output Voltage + + + o PMIC - Power Management IC. An IC that contains numerous regulators + and often contains other susbsystems. + + + o Consumer - Electronic device that is supplied power by a regulator. + Consumers can be classified into two types:- + + Static: consumer does not change it's supply voltage or + current limit. It only needs to enable or disable it's + power supply. It's supply voltage is set by the hardware, + bootloader, firmware or kernel board initialisation code. + + Dynamic: consumer needs to change it's supply voltage or + current limit to meet operation demands. + + + o Power Domain - Electronic circuit that is supplied it's input power by the + output power of a regulator, switch or by another power + domain. + + The supply regulator may be behind a switch(s). i.e. + + Regulator -+-> Switch-1 -+-> Switch-2 --> [Consumer A] + | | + | +-> [Consumer B], [Consumer C] + | + +-> [Consumer D], [Consumer E] + + That is one regulator and three power domains: + + Domain 1: Switch-1, Consumers D & E. + Domain 2: Switch-2, Consumers B & C. + Domain 3: Consumer A. + + and this represents a "supplies" relationship: + + Domain-1 --> Domain-2 --> Domain-3. + + A power domain may have regulators that are supplied power + by other regulators. i.e. + + Regulator-1 -+-> Regulator-2 -+-> [Consumer A] + | + +-> [Consumer B] + + This gives us two regulators and two power domains: + + Domain 1: Regulator-2, Consumer B. + Domain 2: Consumer A. + + and a "supplies" relationship: + + Domain-1 --> Domain-2 + + + o Constraints - Constraints are used to define power levels for performance + and hardware protection. Constraints exist at three levels: + + Regulator Level: This is defined by the regulator hardware + operating parameters and is specified in the regulator + datasheet. i.e. + + - voltage output is in the range 800mV -> 3500mV. + - regulator current output limit is 20mA @ 5V but is + 10mA @ 10V. + + Power Domain Level: This is defined in software by kernel + level board initialisation code. It is used to constrain a + power domain to a particular power range. i.e. + + - Domain-1 voltage is 3300mV + - Domain-2 voltage is 1400mV -> 1600mV + - Domain-3 current limit is 0mA -> 20mA. + + Consumer Level: This is defined by consumer drivers + dynamically setting voltage or current limit levels. + + e.g. a consumer backlight driver asks for a current increase + from 5mA to 10mA to increase LCD illumination. This passes + to through the levels as follows :- + + Consumer: need to increase LCD brightness. Lookup and + request next current mA value in brightness table (the + consumer driver could be used on several different + personalities based upon the same reference device). + + Power Domain: is the new current limit within the domain + operating limits for this domain and system state (e.g. + battery power, USB power) + + Regulator Domains: is the new current limit within the + regulator operating parameters for input/ouput voltage. + + If the regulator request passes all the constraint tests + then the new regulator value is applied. + + +Design +====== + +The framework is designed and targeted at SoC based devices but may also be +relevant to non SoC devices and is split into the following four interfaces:- + + + 1. Consumer driver interface. + + This uses a similar API to the kernel clock interface in that consumer + drivers can get and put a regulator (like they can with clocks atm) and + get/set voltage, current limit, mode, enable and disable. This should + allow consumers complete control over their supply voltage and current + limit. This also compiles out if not in use so drivers can be reused in + systems with no regulator based power control. + + See Documentation/power/regulator/consumer.txt + + 2. Regulator driver interface. + + This allows regulator drivers to register their regulators and provide + operations to the core. It also has a notifier call chain for propagating + regulator events to clients. + + See Documentation/power/regulator/regulator.txt + + 3. Machine interface. + + This interface is for machine specific code and allows the creation of + voltage/current domains (with constraints) for each regulator. It can + provide regulator constraints that will prevent device damage through + overvoltage or over current caused by buggy client drivers. It also + allows the creation of a regulator tree whereby some regulators are + supplied by others (similar to a clock tree). + + See Documentation/power/regulator/machine.txt + + 4. Userspace ABI. + + The framework also exports a lot of useful voltage/current/opmode data to + userspace via sysfs. This could be used to help monitor device power + consumption and status. + + See Documentation/ABI/testing/regulator-sysfs.txt diff --git a/Documentation/power/regulator/regulator.txt b/Documentation/power/regulator/regulator.txt new file mode 100644 index 000000000000..a69050143592 --- /dev/null +++ b/Documentation/power/regulator/regulator.txt @@ -0,0 +1,30 @@ +Regulator Driver Interface +========================== + +The regulator driver interface is relatively simple and designed to allow +regulator drivers to register their services with the core framework. + + +Registration +============ + +Drivers can register a regulator by calling :- + +struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc, + void *reg_data); + +This will register the regulators capabilities and operations the regulator +core. The core does not touch reg_data (private to regulator driver). + +Regulators can be unregistered by calling :- + +void regulator_unregister(struct regulator_dev *rdev); + + +Regulator Events +================ +Regulators can send events (e.g. over temp, under voltage, etc) to consumer +drivers by calling :- + +int regulator_notifier_call_chain(struct regulator_dev *rdev, + unsigned long event, void *data); |