diff options
Diffstat (limited to 'Documentation/devicetree')
3 files changed, 23 insertions, 12 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt index 09fc02b99845..a5c1db95b3ec 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/snps,archs-idu-intc.txt @@ -1,20 +1,30 @@ * ARC-HS Interrupt Distribution Unit - This optional 2nd level interrupt controller can be used in SMP configurations for - dynamic IRQ routing, load balancing of common/external IRQs towards core intc. + This optional 2nd level interrupt controller can be used in SMP configurations + for dynamic IRQ routing, load balancing of common/external IRQs towards core + intc. Properties: - compatible: "snps,archs-idu-intc" - interrupt-controller: This is an interrupt controller. -- #interrupt-cells: Must be <1>. - - Value of the cell specifies the "common" IRQ from peripheral to IDU. Number N - of the particular interrupt line of IDU corresponds to the line N+24 of the - core interrupt controller. - - intc accessed via the special ARC AUX register interface, hence "reg" property - is not specified. +- #interrupt-cells: Must be <1> or <2>. + + Value of the first cell specifies the "common" IRQ from peripheral to IDU. + Number N of the particular interrupt line of IDU corresponds to the line N+24 + of the core interrupt controller. + + The (optional) second cell specifies any of the following flags: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 2 = NOT SUPPORTED (high-to-low edge triggered) + 4 = active high level-sensitive <<< DEFAULT + 8 = NOT SUPPORTED (active low level-sensitive) + When no second cell is specified, the interrupt is assumed to be level + sensitive. + + The interrupt controller is accessed via the special ARC AUX register + interface, hence "reg" property is not specified. Example: core_intc: core-interrupt-controller { diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index 4ac21cef370e..113e7ac79aad 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -12,6 +12,7 @@ Required properties: - "microchip,ksz8565" - "microchip,ksz9893" - "microchip,ksz9563" + - "microchip,ksz8563" Optional properties: diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 63c73fafe26d..0b61a90f1592 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -15,10 +15,10 @@ Required properties: Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC. - Use "sifive,fu540-macb" for SiFive FU540-C000 SoC. + Use "sifive,fu540-c000-gem" for SiFive FU540-C000 SoC. Or the generic form: "cdns,emac". - reg: Address and length of the register set for the device - For "sifive,fu540-macb", second range is required to specify the + For "sifive,fu540-c000-gem", second range is required to specify the address and length of the registers for GEMGXL Management block. - interrupts: Should contain macb interrupt - phy-mode: See ethernet.txt file in the same directory. |