diff options
Diffstat (limited to 'Documentation/devicetree')
10 files changed, 197 insertions, 31 deletions
diff --git a/Documentation/devicetree/bindings/iio/accel/adxl372.txt b/Documentation/devicetree/bindings/iio/accel/adxl372.txt new file mode 100644 index 000000000000..a289964756a7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/adxl372.txt @@ -0,0 +1,33 @@ +Analog Devices ADXL372 3-Axis, +/-(200g) Digital Accelerometer + +http://www.analog.com/media/en/technical-documentation/data-sheets/adxl372.pdf + +Required properties: + - compatible : should be "adi,adxl372" + - reg: the I2C address or SPI chip select number for the device + +Required properties for SPI bus usage: + - spi-max-frequency: Max SPI frequency to use + +Optional properties: + - interrupts: interrupt mapping for IRQ as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example for a I2C device node: + + accelerometer@53 { + compatible = "adi,adxl372"; + reg = <0x53>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + }; + +Example for a SPI device node: + + accelerometer@0 { + compatible = "adi,adxl372"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/mcp3911.txt b/Documentation/devicetree/bindings/iio/adc/mcp3911.txt new file mode 100644 index 000000000000..3071f48fb30b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/mcp3911.txt @@ -0,0 +1,30 @@ +* Microchip MCP3911 Dual channel analog front end (ADC) + +Required properties: + - compatible: Should be "microchip,mcp3911" + - reg: SPI chip select number for the device + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt. + Max frequency for this chip is 20MHz. + +Optional properties: + - clocks: Phandle and clock identifier for sampling clock + - interrupt-parent: Phandle to the parent interrupt controller + - interrupts: IRQ line for the ADC + - microchip,device-addr: Device address when multiple MCP3911 chips are present on the + same SPI bus. Valid values are 0-3. Defaults to 0. + - vref-supply: Phandle to the external reference voltage supply. + +Example: +adc@0 { + compatible = "microchip,mcp3911"; + reg = <0>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_EDGE_RISING>; + spi-max-frequency = <20000000>; + microchip,device-addr = <0>; + vref-supply = <&vref_reg>; + clocks = <&xtal>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt index 0fb46137f936..b3c86f4ac7cd 100644 --- a/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/qcom,spmi-vadc.txt @@ -1,7 +1,9 @@ -Qualcomm's SPMI PMIC voltage ADC +Qualcomm's SPMI PMIC ADC -SPMI PMIC voltage ADC (VADC) provides interface to clients to read -voltage. The VADC is a 15-bit sigma-delta ADC. +- SPMI PMIC voltage ADC (VADC) provides interface to clients to read + voltage. The VADC is a 15-bit sigma-delta ADC. +- SPMI PMIC5 voltage ADC (ADC) provides interface to clients to read + voltage. The VADC is a 16-bit sigma-delta ADC. VADC node: @@ -9,11 +11,13 @@ VADC node: Usage: required Value type: <string> Definition: Should contain "qcom,spmi-vadc". + Should contain "qcom,spmi-adc5" for PMIC5 ADC driver. + Should contain "qcom,spmi-adc-rev2" for PMIC rev2 ADC driver. - reg: Usage: required Value type: <prop-encoded-array> - Definition: VADC base address and length in the SPMI PMIC register map. + Definition: VADC base address in the SPMI PMIC register map. - #address-cells: Usage: required @@ -45,13 +49,26 @@ Channel node properties: Definition: ADC channel number. See include/dt-bindings/iio/qcom,spmi-vadc.h +- label: + Usage: required for "qcom,spmi-adc5" and "qcom,spmi-adc-rev2" + Value type: <empty> + Definition: ADC input of the platform as seen in the schematics. + For thermistor inputs connected to generic AMUX or GPIO inputs + these can vary across platform for the same pins. Hence select + the platform schematics name for this channel. + - qcom,decimation: Usage: optional Value type: <u32> Definition: This parameter is used to decrease ADC sampling rate. Quicker measurements can be made by reducing decimation ratio. - Valid values are 512, 1024, 2048, 4096. - If property is not found, default value of 512 will be used. + - For compatible property "qcom,spmi-vadc", valid values are + 512, 1024, 2048, 4096. If property is not found, default value + of 512 will be used. + - For compatible property "qcom,spmi-adc5", valid values are 250, 420 + and 840. If property is not found, default value of 840 is used. + - For compatible property "qcom,spmi-adc-rev2", valid values are 256, + 512 and 1024. If property is not present, default value is 1024. - qcom,pre-scaling: Usage: optional @@ -66,21 +83,38 @@ Channel node properties: - qcom,ratiometric: Usage: optional Value type: <empty> - Definition: Channel calibration type. If this property is specified - VADC will use the VDD reference (1.8V) and GND for channel - calibration. If property is not found, channel will be - calibrated with 0.625V and 1.25V reference channels, also - known as absolute calibration. + Definition: Channel calibration type. + - For compatible property "qcom,spmi-vadc", if this property is + specified VADC will use the VDD reference (1.8V) and GND for + channel calibration. If property is not found, channel will be + calibrated with 0.625V and 1.25V reference channels, also + known as absolute calibration. + - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2", + if this property is specified VADC will use the VDD reference + (1.875V) and GND for channel calibration. If property is not found, + channel will be calibrated with 0V and 1.25V reference channels, + also known as absolute calibration. - qcom,hw-settle-time: Usage: optional Value type: <u32> Definition: Time between AMUX getting configured and the ADC starting - conversion. Delay = 100us * (value) for value < 11, and - 2ms * (value - 10) otherwise. - Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800, - 900 us and 1, 2, 4, 6, 8, 10 ms - If property is not found, channel will use 0us. + conversion. The 'hw_settle_time' is an index used from valid values + and programmed in hardware to achieve the hardware settling delay. + - For compatible property "qcom,spmi-vadc" and "qcom,spmi-adc-rev2", + Delay = 100us * (hw_settle_time) for hw_settle_time < 11, + and 2ms * (hw_settle_time - 10) otherwise. + Valid values are: 0, 100, 200, 300, 400, 500, 600, 700, 800, + 900 us and 1, 2, 4, 6, 8, 10 ms. + If property is not found, channel will use 0us. + - For compatible property "qcom,spmi-adc5", delay = 15us for + value 0, 100us * (value) for values < 11, + and 2ms * (value - 10) otherwise. + Valid values are: 15, 100, 200, 300, 400, 500, 600, 700, 800, + 900 us and 1, 2, 4, 6, 8, 10 ms + Certain controller digital versions have valid values of + 15, 100, 200, 300, 400, 500, 600, 700, 1, 2, 4, 8, 16, 32, 64, 128 ms + If property is not found, channel will use 15us. - qcom,avg-samples: Usage: optional @@ -89,13 +123,18 @@ Channel node properties: Averaging provides the option to obtain a single measurement from the ADC that is an average of multiple samples. The value selected is 2^(value). - Valid values are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512 - If property is not found, 1 sample will be used. + - For compatible property "qcom,spmi-vadc", valid values + are: 1, 2, 4, 8, 16, 32, 64, 128, 256, 512 + If property is not found, 1 sample will be used. + - For compatible property "qcom,spmi-adc5" and "qcom,spmi-adc-rev2", + valid values are: 1, 2, 4, 8, 16 + If property is not found, 1 sample will be used. NOTE: -Following channels, also known as reference point channels, are used for -result calibration and their channel configuration nodes should be defined: +For compatible property "qcom,spmi-vadc" following channels, also known as +reference point channels, are used for result calibration and their channel +configuration nodes should be defined: VADC_REF_625MV and/or VADC_SPARE1(based on PMIC version) VADC_REF_1250MV, VADC_GND_REF and VADC_VDD_VADC. @@ -104,7 +143,7 @@ Example: /* VADC node */ pmic_vadc: vadc@3100 { compatible = "qcom,spmi-vadc"; - reg = <0x3100 0x100>; + reg = <0x3100>; interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; #address-cells = <1>; #size-cells = <0>; diff --git a/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt b/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt index 8aad960de50b..b4daa15dcf15 100644 --- a/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/sprd,sc27xx-adc.txt @@ -12,6 +12,8 @@ Required properties: - interrupts: The interrupt number for the ADC device. - #io-channel-cells: Number of cells in an IIO specifier. - hwlocks: Reference to a phandle of a hwlock provider node. +- nvmem-cells: A phandle to the calibration cells provided by eFuse device. +- nvmem-cell-names: Should be "big_scale_calib", "small_scale_calib". Example: @@ -32,5 +34,7 @@ Example: interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; #io-channel-cells = <1>; hwlocks = <&hwlock 4>; + nvmem-cells = <&adc_big_scale>, <&adc_small_scale>; + nvmem-cell-names = "big_scale_calib", "small_scale_calib"; }; }; diff --git a/Documentation/devicetree/bindings/iio/dac/ad5758.txt b/Documentation/devicetree/bindings/iio/dac/ad5758.txt index bba01a5cab1b..2f607f41f9d3 100644 --- a/Documentation/devicetree/bindings/iio/dac/ad5758.txt +++ b/Documentation/devicetree/bindings/iio/dac/ad5758.txt @@ -50,6 +50,9 @@ Required properties: Optional properties: + - reset-gpios : GPIO spec for the RESET pin. If specified, it will be + asserted during driver probe. + - adi,dc-dc-ilim-microamp: The dc-to-dc converter current limit The following values are currently supported [uA]: * 150000 @@ -71,6 +74,8 @@ AD5758 Example: spi-max-frequency = <1000000>; spi-cpha; + reset-gpios = <&gpio 22 0>; + adi,dc-dc-mode = <2>; adi,range-microvolt = <0 10000000>; adi,dc-dc-ilim-microamp = <200000>; diff --git a/Documentation/devicetree/bindings/iio/dac/ltc1660.txt b/Documentation/devicetree/bindings/iio/dac/ltc1660.txt new file mode 100644 index 000000000000..c5b5f22d6c64 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/ltc1660.txt @@ -0,0 +1,21 @@ +* Linear Technology Micropower octal 8-Bit and 10-Bit DACs + +Required properties: + - compatible: Must be one of the following: + "lltc,ltc1660" + "lltc,ltc1665" + - reg: SPI chip select number for the device + - vref-supply: Phandle to the voltage reference supply + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt. + Max frequency for this chip is 5 MHz. + +Example: +dac@0 { + compatible = "lltc,ltc1660"; + reg = <0>; + spi-max-frequency = <5000000>; + vref-supply = <&vref_reg>; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt index b2f27da847b8..6ab9a9d196b0 100644 --- a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -20,6 +20,7 @@ Required properties: bindings. Optional properties: + - vddio-supply: regulator phandle for VDDIO supply - mount-matrix: an optional 3x3 mounting rotation matrix - i2c-gate node. These devices also support an auxiliary i2c bus. This is simple enough to be described using the i2c-gate binding. See diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index ea2d6e0ae4c5..879322ad50fd 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -7,6 +7,7 @@ Required properties: "st,lsm6dsl" "st,lsm6dsm" "st,ism330dlc" + "st,lsm6dso" - reg: i2c address of the sensor / spi cs line Optional properties: diff --git a/Documentation/devicetree/bindings/iio/light/tsl2772.txt b/Documentation/devicetree/bindings/iio/light/tsl2772.txt new file mode 100644 index 000000000000..1c5e6f17a1df --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2772.txt @@ -0,0 +1,42 @@ +* AMS/TAOS ALS and proximity sensor + +Required properties: + + - compatible: Should be one of + "amstaos,tsl2571" + "amstaos,tsl2671" + "amstaos,tmd2671" + "amstaos,tsl2771" + "amstaos,tmd2771" + "amstaos,tsl2572" + "amstaos,tsl2672" + "amstaos,tmd2672" + "amstaos,tsl2772" + "amstaos,tmd2772" + "avago,apds9930" + - reg: the I2C address of the device + +Optional properties: + + - amstaos,proximity-diodes - proximity diodes to enable. <0>, <1>, or <0 1> + are the only valid values. + - led-max-microamp - current for the proximity LED. Must be 100000, 50000, + 25000, or 13000. + - vdd-supply: phandle to the regulator that provides power to the sensor. + - vddio-supply: phandle to the regulator that provides power to the bus. + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + +Example: + +tsl2772@39 { + compatible = "amstaos,tsl2772"; + reg = <0x39>; + interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&pm8941_l17>; + vddio-supply = <&pm8941_lvs1>; + amstaos,proximity-diodes = <0>; + led-max-microamp = <100000>; +}; diff --git a/Documentation/devicetree/bindings/trivial-devices.txt b/Documentation/devicetree/bindings/trivial-devices.txt index 763a2808a95c..a977ccef7230 100644 --- a/Documentation/devicetree/bindings/trivial-devices.txt +++ b/Documentation/devicetree/bindings/trivial-devices.txt @@ -21,16 +21,6 @@ adi,adt7490 +/-1C TDM Extended Temp Range I.C adi,adxl345 Three-Axis Digital Accelerometer adi,adxl346 Three-Axis Digital Accelerometer (backward-compatibility value "adi,adxl345" must be listed too) ams,iaq-core AMS iAQ-Core VOC Sensor -amstaos,tsl2571 AMS/TAOS ALS and proximity sensor -amstaos,tsl2671 AMS/TAOS ALS and proximity sensor -amstaos,tmd2671 AMS/TAOS ALS and proximity sensor -amstaos,tsl2771 AMS/TAOS ALS and proximity sensor -amstaos,tmd2771 AMS/TAOS ALS and proximity sensor -amstaos,tsl2572 AMS/TAOS ALS and proximity sensor -amstaos,tsl2672 AMS/TAOS ALS and proximity sensor -amstaos,tmd2672 AMS/TAOS ALS and proximity sensor -amstaos,tsl2772 AMS/TAOS ALS and proximity sensor -amstaos,tmd2772 AMS/TAOS ALS and proximity sensor at,24c08 i2c serial eeprom (24cxx) atmel,at97sc3204t i2c trusted platform module (TPM) capella,cm32181 CM32181: Ambient Light Sensor |