diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
8 files changed, 599 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/tps6507x.txt b/Documentation/devicetree/bindings/mfd/tps6507x.txt new file mode 100755 index 000000000000..8fffa3c5ed40 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps6507x.txt @@ -0,0 +1,91 @@ +TPS6507x Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps6507x" +- reg: I2C slave address +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the + given device need to be present. The definition for each of these nodes + is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. + + The valid regulator-compatible values are: + tps6507x: vdcdc1, vdcdc2, vdcdc3, vldo1, vldo2 +- xxx-supply: Input voltage supply regulator. + These entries are required if regulators are enabled for a device. + Missing of these properties can cause the regulator registration + fails. + If some of input supply is powered through battery or always-on + supply then also it is require to have these parameters with proper + node handle of always on power supply. + tps6507x: + vindcdc1_2-supply: VDCDC1 and VDCDC2 input. + vindcdc3-supply : VDCDC3 input. + vldo1_2-supply : VLDO1 and VLDO2 input. + +Regulator Optional properties: +- defdcdc_default: It's property of DCDC2 and DCDC3 regulators. + 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND. + 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH. + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps6507x@48 { + compatible = "ti,tps6507x"; + reg = <0x48>; + + vindcdc1_2-supply = <&vbat>; + vindcdc3-supply = <...>; + vinldo1_2-supply = <...>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vdcdc1_reg: regulator@0 { + regulator-compatible = "VDCDC1"; + reg = <0>; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + }; + vdcdc2_reg: regulator@1 { + regulator-compatible = "VDCDC2"; + reg = <1>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + vdcdc3_reg: regulator@2 { + regulator-compatible = "VDCDC3"; + reg = <2>; + regulator-min-microvolt = <950000> + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + ldo1_reg: regulator@3 { + regulator-compatible = "LDO1"; + reg = <3>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <1890000>; + regulator-always-on; + regulator-boot-on; + }; + ldo2_reg: regulator@4 { + regulator-compatible = "LDO2"; + reg = <4>; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1320000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt new file mode 100644 index 000000000000..dff0e5f995e2 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -0,0 +1,60 @@ +* Allwinner A1X Pin Controller + +The pins controlled by sunXi pin controller are organized in banks, +each bank has 32 pins. Each pin has 7 multiplexing functions, with +the first two functions being GPIO in and out. The configuration on +the pins includes drive strength and pull-up. + +Required properties: +- compatible: "allwinner,<soc>-pinctrl". Supported SoCs for now are: + sun5i-a13. +- reg: Should contain the register physical address and length for the + pin controller. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices. + +A pinctrl node should contain at least one subnodes representing the +pinctrl groups available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, drive strength and pullups. If one of these options is +not set, its actual value will be unspecified. + +Required subnode-properties: + +- allwinner,pins: List of strings containing the pin name. +- allwinner,function: Function to mux the pins listed above to. + +Optional subnode-properties: +- allwinner,drive: Integer. Represents the current sent to the pin + 0: 10 mA + 1: 20 mA + 2: 30 mA + 3: 40 mA +- allwinner,pull: Integer. + 0: No resistor + 1: Pull-up resistor + 2: Pull-down resistor + +Examples: + +pinctrl@01c20800 { + compatible = "allwinner,sun5i-a13-pinctrl"; + reg = <0x01c20800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + uart1_pins_a: uart1@0 { + allwinner,pins = "PE10", "PE11"; + allwinner,function = "uart1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + uart1_pins_b: uart1@1 { + allwinner,pins = "PG3", "PG4"; + allwinner,function = "uart1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt new file mode 100644 index 000000000000..e204d009f16c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt @@ -0,0 +1,120 @@ +NVIDIA Tegra114 pinmux controller + +The Tegra114 pinctrl binding is very similar to the Tegra20 and Tegra30 +pinctrl binding, as described in nvidia,tegra20-pinmux.txt and +nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as +a baseline, and only documents the differences between the two bindings. + +Required properties: +- compatible: "nvidia,tegra114-pinmux" +- reg: Should contain the register physical address and length for each of + the pad control and mux registers. The first bank of address must be the + driver strength pad control register address and second bank address must + be pinmux register address. + +Tegra114 adds the following optional properties for pin configuration subnodes: +- nvidia,enable-input: Integer. Enable the pin's input path. 0: no, 1: yes. +- nvidia,open-drain: Integer. Enable open drain mode. 0: no, 1: yes. +- nvidia,lock: Integer. Lock the pin configuration against further changes + until reset. 0: no, 1: yes. +- nvidia,io-reset: Integer. Reset the IO path. 0: no, 1: yes. +- nvidia,rcv-sel: Integer. Select VIL/VIH receivers. 0: normal, 1: high. +- nvidia,drive-type: Integer. Valid range 0...3. + +As with Tegra20 and Terga30, see the Tegra TRM for complete details regarding +which groups support which functionality. + +Valid values for pin and group names are: + + per-pin mux groups: + + These all support nvidia,function, nvidia,tristate, nvidia,pull, + nvidia,enable-input, nvidia,lock. Some support nvidia,open-drain, + nvidia,io-reset and nvidia,rcv-sel. + + ulpi_data0_po1, ulpi_data1_po2, ulpi_data2_po3, ulpi_data3_po4, + ulpi_data4_po5, ulpi_data5_po6, ulpi_data6_po7, ulpi_data7_po0, + ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3, dap3_fs_pp0, + dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3, pv0, pv1, sdmmc1_clk_pz0, + sdmmc1_cmd_pz1, sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6, + sdmmc1_dat0_py7, clk2_out_pw5, clk2_req_pcc5, hdmi_int_pn7, ddc_scl_pv4, + ddc_sda_pv5, uart2_rxd_pc3, uart2_txd_pc2, uart2_rts_n_pj6, + uart2_cts_n_pj5, uart3_txd_pw6, uart3_rxd_pw7, uart3_cts_n_pa1, + uart3_rts_n_pc0, pu0, pu1, pu2, pu3, pu4, pu5, pu6, gen1_i2c_sda_pc5, + gen1_i2c_scl_pc4, dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6, dap4_sclk_pp7, + clk3_out_pee0, clk3_req_pee1, gmi_wp_n_pc7, gmi_iordy_pi5, gmi_wait_pi7, + gmi_adv_n_pk0, gmi_clk_pk1, gmi_cs0_n_pj0, gmi_cs1_n_pj2, gmi_cs2_n_pk3, + gmi_cs3_n_pk4, gmi_cs4_n_pk2, gmi_cs6_n_pi3, gmi_cs7_n_pi6, gmi_ad0_pg0, + gmi_ad1_pg1, gmi_ad2_pg2, gmi_ad3_pg3, gmi_ad4_pg4, gmi_ad5_pg5, + gmi_ad6_pg6, gmi_ad7_pg7, gmi_ad8_ph0, gmi_ad9_ph1, gmi_ad10_ph2, + gmi_ad11_ph3, gmi_ad12_ph4, gmi_ad13_ph5, gmi_ad14_ph6, gmi_ad15_ph7, + gmi_a16_pj7, gmi_a17_pb0, gmi_a18_pb1, gmi_a19_pk7, gmi_wr_n_pi0, + gmi_oe_n_pi1, gmi_dqs_p_pj3, gmi_rst_n_pi4, gen2_i2c_scl_pt5, + gen2_i2c_sda_pt6, sdmmc4_clk_pcc4, sdmmc4_cmd_pt7, sdmmc4_dat0_paa0, + sdmmc4_dat1_paa1, sdmmc4_dat2_paa2, sdmmc4_dat3_paa3, sdmmc4_dat4_paa4, + sdmmc4_dat5_paa5, sdmmc4_dat6_paa6, sdmmc4_dat7_paa7, cam_mclk_pcc0, + pcc1, pbb0, cam_i2c_scl_pbb1, cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, + pbb7, pcc2, pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, kb_row0_pr0, kb_row1_pr1, + kb_row2_pr2, kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, + kb_row7_pr7, kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_col0_pq0, + kb_col1_pq1, kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5, + kb_col6_pq6, kb_col7_pq7, clk_32k_out_pa0, sys_clk_req_pz5, core_pwr_req, + cpu_pwr_req, pwr_int_n, owr, dap1_fs_pn0, dap1_din_pn1, dap1_dout_pn2, + dap1_sclk_pn3, clk1_req_pee2, clk1_out_pw4, spdif_in_pk6, spdif_out_pk5, + dap2_fs_pa2, dap2_din_pa4, dap2_dout_pa5, dap2_sclk_pa3, dvfs_pwm_px0, + gpio_x1_aud_px1, gpio_x3_aud_px3, dvfs_clk_px2, gpio_x4_aud_px4, + gpio_x5_aud_px5, gpio_x6_aud_px6, gpio_x7_aud_px7, sdmmc3_clk_pa6, + sdmmc3_cmd_pa7, sdmmc3_dat0_pb7, sdmmc3_dat1_pb6, sdmmc3_dat2_pb5, + sdmmc3_dat3_pb4, hdmi_cec_pee3, sdmmc1_wp_n_pv3, sdmmc3_cd_n_pv2, + gpio_w2_aud_pw2, gpio_w3_aud_pw3, usb_vbus_en0_pn4, usb_vbus_en1_pn5, + sdmmc3_clk_lb_in_pee5, sdmmc3_clk_lb_out_pee4, reset_out_n. + + drive groups: + + These all support nvidia,pull-down-strength, nvidia,pull-up-strength, + nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all + support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode + and nvidia,drive-type. + + ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, dap1, dap2, dap3, dap4, + dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg, + gmh, owr, uda. + +Example: + + pinmux: pinmux { + compatible = "nvidia,tegra114-pinmux"; + reg = <0x70000868 0x148 /* Pad control registers */ + 0x70003000 0x40c>; /* PinMux registers */ + }; + +Example board file extract: + + pinctrl { + sdmmc4_default: pinmux { + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4", + nvidia,function = "sdmmc4"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + sdmmc4_dat0_paa0 { + nvidia,pins = "sdmmc4_dat0_paa0", + "sdmmc4_dat1_paa1", + "sdmmc4_dat2_paa2", + "sdmmc4_dat3_paa3", + "sdmmc4_dat4_paa4", + "sdmmc4_dat5_paa5", + "sdmmc4_dat6_paa6", + "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + }; + }; + + sdhci@78000400 { + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc4_default>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt new file mode 100644 index 000000000000..9a2f3f420526 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt @@ -0,0 +1,140 @@ +ST Ericsson Nomadik pinmux controller + +Required properties: +- compatible: "stericsson,nmk-pinctrl", "stericsson,nmk-pinctrl-db8540", + "stericsson,nmk-pinctrl-stn8815" +- reg: Should contain the register physical address and length of the PRCMU. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +ST Ericsson's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as input, output, pull up, pull down... + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Required subnode-properties: +- ste,pins : An array of strings. Each string contains the name of a pin or + group. + +Optional subnode-properties: +- ste,function: A string containing the name of the function to mux to the + pin or group. + +- ste,config: Handle of pin configuration node (e.g. ste,config = <&slpm_in_wkup_pdis>) + +- ste,input : <0/1/2> + 0: input with no pull + 1: input with pull up, + 2: input with pull down, + +- ste,output: <0/1/2> + 0: output low, + 1: output high, + 2: output (value is not specified). + +- ste,sleep: <0/1> + 0: sleep mode disable, + 1: sleep mode enable. + +- ste,sleep-input: <0/1/2/3> + 0: sleep input with no pull, + 1: sleep input with pull up, + 2: sleep input with pull down. + 3: sleep input and keep last input configuration (no pull, pull up or pull down). + +- ste,sleep-output: <0/1/2> + 0: sleep output low, + 1: sleep output high, + 2: sleep output (value is not specified). + +- ste,sleep-gpio: <0/1> + 0: disable sleep gpio mode, + 1: enable sleep gpio mode. + +- ste,sleep-wakeup: <0/1> + 0: wake-up detection enabled, + 1: wake-up detection disabled. + +- ste,sleep-pull-disable: <0/1> + 0: GPIO pull-up or pull-down resistor is enabled, when pin is an input, + 1: GPIO pull-up and pull-down resistor are disabled. + +Example board file extract: + + pinctrl@80157000 { + compatible = "stericsson,nmk-pinctrl"; + reg = <0x80157000 0x2000>; + + pinctrl-names = "default"; + + slpm_in_wkup_pdis: slpm_in_wkup_pdis { + ste,sleep = <1>; + ste,sleep-input = <3>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + slpm_out_hi_wkup_pdis: slpm_out_hi_wkup_pdis { + ste,sleep = <1>; + ste,sleep-output = <1>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + slpm_out_wkup_pdis: slpm_out_wkup_pdis { + ste,sleep = <1>; + ste,sleep-output = <2>; + ste,sleep-wakeup = <1>; + ste,sleep-pull-disable = <0>; + }; + + uart0 { + uart0_default_mux: uart0_mux { + u0_default_mux { + ste,function = "u0"; + ste,pins = "u0_a_1"; + }; + }; + uart0_default_mode: uart0_default { + uart0_default_cfg1 { + ste,pins = "GPIO0", "GPIO2"; + ste,input = <1>; + }; + + uart0_default_cfg2 { + ste,pins = "GPIO1", "GPIO3"; + ste,output = <1>; + }; + }; + uart0_sleep_mode: uart0_sleep { + uart0_sleep_cfg1 { + ste,pins = "GPIO0", "GPIO2"; + ste,config = <&slpm_in_wkup_pdis>; + }; + uart0_sleep_cfg2 { + ste,pins = "GPIO1"; + ste,config = <&slpm_out_hi_wkup_pdis>; + }; + uart0_sleep_cfg3 { + ste,pins = "GPIO3"; + ste,config = <&slpm_out_wkup_pdis>; + }; + }; + }; + }; + + uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 0x4>; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>; + pinctrl-1 = <&uart0_sleep_mode>; + }; diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt index 357758cb6e92..758eae24082a 100644 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt @@ -9,6 +9,11 @@ Required properties: - anatop-min-voltage: Minimum voltage of this regulator - anatop-max-voltage: Maximum voltage of this regulator +Optional properties: +- anatop-delay-reg-offset: Anatop MFD step time register offset +- anatop-delay-bit-shift: Bit shift for the step time register +- anatop-delay-bit-width: Number of bits used in the step time register + Any property defined as part of the core regulator binding, defined in regulator.txt, can also be used. @@ -23,6 +28,9 @@ Example: anatop-reg-offset = <0x140>; anatop-vol-bit-shift = <9>; anatop-vol-bit-width = <5>; + anatop-delay-reg-offset = <0x170>; + anatop-delay-bit-shift = <24>; + anatop-delay-bit-width = <2>; anatop-min-bit-val = <1>; anatop-min-voltage = <725000>; anatop-max-voltage = <1300000>; diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt new file mode 100644 index 000000000000..a35ff99003a5 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -0,0 +1,152 @@ +* Samsung S5M8767 Voltage and Current Regulator + +The Samsung S5M8767 is a multi-function device which includes volatage and +current regulators, rtc, charger controller and other sub-blocks. It is +interfaced to the host controller using a i2c interface. Each sub-block is +addressed by the host system using different i2c slave address. This document +describes the bindings for 'pmic' sub-block of s5m8767. + +Required properties: +- compatible: Should be "samsung,s5m8767-pmic". +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck2 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck3 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV) + units for buck4 when changing voltage using gpio dvs. Refer to [1] below + for additional information. + +- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used + for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines. + +[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage' + property should specify atleast one voltage level (which would be a + safe operating voltage). + + If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional + property is specified, then all the eight voltage values for the + 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s5m8767 are delivered to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for 'irq1' interrupt. + - Second interrupt specifier is for 'alert' interrupt. +- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs. +- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs. +- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs. + +Additional properties required if either of the optional properties are used: + +- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from + the possible 8 options selectable by the dvs gpios. The value of this + property should be between 0 and 7. If not specified or if out of range, the + default value of this property is set to 0. + +- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used + for dvs. The format of the gpio specifier depends in the gpio controller. + +Regulators: The regulators of s5m8767 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE_1.0V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; /* Normal Mode */ + }; + }; +The above regulator entries are defined in regulator bindings documentation +except op_mode description. + - op_mode: describes the different operating modes of the LDO's with + power mode change in SOC. The different possible values are, + 0 - always off mode + 1 - on in normal mode + 2 - low power mode + 3 - suspend mode + +The following are the names of the regulators that the s5m8767 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s5m8767. + + - LDOn + - valid values for n are 1 to 28 + - Example: LDO0, LD01, LDO28 + - BUCKn + - valid values for n are 1 to 9. + - Example: BUCK1, BUCK2, BUCK9 + +The bindings inside the regulator nodes use the standard regulator bindings +which are documented elsewhere. + +Example: + + s5m8767_pmic@66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + + s5m8767,pmic-buck2-uses-gpio-dvs; + s5m8767,pmic-buck3-uses-gpio-dvs; + s5m8767,pmic-buck4-uses-gpio-dvs; + + s5m8767,pmic-buck-default-dvs-idx = <0>; + + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */ + <&gpx0 1 1 0 0>, /* DVS2 */ + <&gpx0 2 1 0 0>; /* DVS3 */ + + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */ + <&gpx2 4 1 0 0>, /* SET2 */ + <&gpx2 5 1 0 0>; /* SET3 */ + + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + op_mode = <1>; /* Normal Mode */ + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt new file mode 100644 index 000000000000..2f7e44a96414 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/tps51632-regulator.txt @@ -0,0 +1,27 @@ +TPS51632 Voltage regulators + +Required properties: +- compatible: Must be "ti,tps51632" +- reg: I2C slave address + +Optional properties: +- ti,enable-pwm-dvfs: Enable the DVFS voltage control through the PWM interface. +- ti,dvfs-step-20mV: The 20mV step voltage when PWM DVFS enabled. Missing this + will set 10mV step voltage in PWM DVFS mode. In normal mode, the voltage + step is 10mV as per datasheet. + +Any property defined as part of the core regulator binding, defined in +regulator.txt, can also be used. + +Example: + + tps51632 { + compatible = "ti,tps51632"; + reg = <0x43>; + regulator-name = "tps51632-vout"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + ti,enable-pwm-dvfs; + ti,dvfs-step-20mV; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 902b1b1f568e..15321373ec8d 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -50,6 +50,7 @@ simtek sirf SiRF Technology, Inc. snps Synopsys, Inc. st STMicroelectronics +ste ST-Ericsson stericsson ST-Ericsson ti Texas Instruments via VIA Technologies, Inc. |