diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
45 files changed, 484 insertions, 169 deletions
diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt index 1e6111333fa8..80ae87a0784b 100644 --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt @@ -3,8 +3,10 @@ Required properties: - compatible : should contain one of the following: - "renesas,sata-r8a7779" for R-Car H1 - - "renesas,sata-r8a7790" for R-Car H2 - - "renesas,sata-r8a7791" for R-Car M2 + - "renesas,sata-r8a7790-es1" for R-Car H2 ES1 + - "renesas,sata-r8a7790" for R-Car H2 other than ES1 + - "renesas,sata-r8a7791" for R-Car M2-W + - "renesas,sata-r8a7793" for R-Car M2-N - reg : address and length of the SATA registers; - interrupts : must consist of one interrupt specifier. diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt index ce6a1a072028..8a3c40829899 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt @@ -30,10 +30,6 @@ should only be used when a device has multiple interrupt parents. Example: interrupts-extended = <&intc1 5 1>, <&intc2 1 0>; -A device node may contain either "interrupts" or "interrupts-extended", but not -both. If both properties are present, then the operating system should log an -error and use only the data in "interrupts". - 2) Interrupt controller nodes ----------------------------- diff --git a/Documentation/devicetree/bindings/mailbox/mailbox.txt b/Documentation/devicetree/bindings/mailbox/mailbox.txt new file mode 100644 index 000000000000..1a2cd3d266db --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/mailbox.txt @@ -0,0 +1,38 @@ +* Generic Mailbox Controller and client driver bindings + +Generic binding to provide a way for Mailbox controller drivers to +assign appropriate mailbox channel to client drivers. + +* Mailbox Controller + +Required property: +- #mbox-cells: Must be at least 1. Number of cells in a mailbox + specifier. + +Example: + mailbox: mailbox { + ... + #mbox-cells = <1>; + }; + + +* Mailbox Client + +Required property: +- mboxes: List of phandle and mailbox channel specifiers. + +Optional property: +- mbox-names: List of identifier strings for each mailbox channel + required by the client. The use of this property + is discouraged in favor of using index in list of + 'mboxes' while requesting a mailbox. Instead the + platforms may define channel indices, in DT headers, + to something legible. + +Example: + pwr_cntrl: power { + ... + mbox-names = "pwr-ctrl", "rpc"; + mboxes = <&mailbox 0 + &mailbox 1>; + }; diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt index 0f8487b88822..e77e167593db 100644 --- a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -11,3 +11,5 @@ Optional properties: are supported on the device. Valid value for SMSC LAN91c111 are 1, 2 or 4. If it's omitted or invalid, the size would be 2 meaning 16-bit access only. +- power-gpios: GPIO to control the PWRDWN pin +- reset-gpios: GPIO to control the RESET pin diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 41aeed38926d..f8fbe9af7b2f 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -7,3 +7,14 @@ And for the interrupt mapping part: Open Firmware Recommended Practice: Interrupt Mapping http://www.openfirmware.org/1275/practice/imap/imap0_9d.pdf + +Additionally to the properties specified in the above standards a host bridge +driver implementation may support the following properties: + +- linux,pci-domain: + If present this property assigns a fixed PCI domain number to a host bridge, + otherwise an unstable (across boots) unique number will be assigned. + It is required to either not set this property at all or set it for all + host bridges in the system, otherwise potentially conflicting domain numbers + may be assigned to root buses behind different host bridges. The domain + number for each host bridge in the system must be unique. diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt index a186181c402b..51b943cc9770 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090-PDC's pin configuration nodes act as a container for an abitrary number +TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt index 4b27c99f7f9d..49d0e6050940 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -TZ1090's pin configuration nodes act as a container for an abitrary number of +TZ1090's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt index daa768956069..ac4da9fe07bd 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt index b5469db1d7ad..e89b4677567d 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Lantiq's pin configuration nodes act as a container for an abitrary number of +Lantiq's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those group(s), and two pin configuration parameters: diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt index 61e73cde9ae9..3c8ce28baad6 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt @@ -9,7 +9,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Tegra's pin configuration nodes act as a container for an abitrary number of +Tegra's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt index c596a6ad3285..5f55be59d914 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt @@ -13,7 +13,7 @@ Optional properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SiRFprimaII's pinmux nodes act as a container for an abitrary number of subnodes. +SiRFprimaII's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a group of pins. Required subnode-properties: diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt index b4480d5c3aca..458615596946 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt @@ -32,7 +32,7 @@ Required properties: Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices. -SPEAr's pinmux nodes act as a container for an abitrary number of subnodes. Each +SPEAr's pinmux nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents muxing for a pin, a group, or a list of pins or groups. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt index 2fb90b37aa09..a7bde64798c7 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt index ffafa1990a30..c4ea61ac56f2 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt @@ -47,7 +47,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -The pin configuration nodes act as a container for an abitrary number of +The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt index e33e4dcdce79..6e88e91feb11 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt index 93b7de91b9f6..eb8d8aa41f20 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt @@ -47,7 +47,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -The pin configuration nodes act as a container for an abitrary number of +The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index d2ea80dc43eb..e4d6a9d20f7d 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -18,7 +18,7 @@ Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". -Qualcomm's pin configuration nodes act as a container for an abitrary number of +Qualcomm's pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt index 0bda229a6171..3899d6a557c1 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt @@ -1,5 +1,20 @@ Freescale FlexTimer Module (FTM) PWM controller +The same FTM PWM device can have a different endianness on different SoCs. The +device tree provides a property to describing this so that an operating system +device driver can handle all variants of the device. Refer to the table below +for the endianness of the FTM PWM block as integrated into the existing SoCs: + + SoC | FTM-PWM endianness + --------+------------------- + Vybrid | LE + LS1 | BE + LS2 | LE + +Please see ../regmap/regmap.txt for more detail about how to specify endian +modes in device tree. + + Required properties: - compatible: Should be "fsl,vf610-ftm-pwm". - reg: Physical base address and length of the controller's registers @@ -16,7 +31,8 @@ Required properties: - pinctrl-names: Must contain a "default" entry. - pinctrl-NNN: One property must exist for each entry in pinctrl-names. See pinctrl/pinctrl-bindings.txt for details of the property values. - +- big-endian: Boolean property, required if the FTM PWM registers use a big- + endian rather than little-endian layout. Example: @@ -32,4 +48,5 @@ pwm0: pwm@40038000 { <&clks VF610_CLK_FTM0_EXT_FIX_EN>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pwm0_1>; + big-endian; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt index d47d15a6a298..b8be3d09ee26 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt @@ -7,8 +7,8 @@ Required properties: "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC - reg: physical base address and length of the controller's registers - clocks: phandle and clock specifier of the PWM reference clock - - #pwm-cells: should be 2. See pwm.txt in this directory for a - description of the cell format. + - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory + for a description of the cell format. Example: diff --git a/Documentation/devicetree/bindings/sound/arndale.txt b/Documentation/devicetree/bindings/sound/arndale.txt new file mode 100644 index 000000000000..0e76946385ae --- /dev/null +++ b/Documentation/devicetree/bindings/sound/arndale.txt @@ -0,0 +1,24 @@ +Audio Binding for Arndale boards + +Required properties: +- compatible : Can be the following, + "samsung,arndale-rt5631" + +- samsung,audio-cpu: The phandle of the Samsung I2S controller +- samsung,audio-codec: The phandle of the audio codec + +Optional: +- samsung,model: The name of the sound-card + +Arndale Boards has many audio daughter cards, one of them is +rt5631/alc5631. Below example shows audio bindings for rt5631/ +alc5631 based codec. + +Example: + +sound { + compatible = "samsung,arndale-rt5631"; + + samsung,audio-cpu = <&i2s0> + samsung,audio-codec = <&rt5631>; +}; diff --git a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt index 60ca07996458..46bc9829c71a 100644 --- a/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt +++ b/Documentation/devicetree/bindings/sound/davinci-mcasp-audio.txt @@ -32,7 +32,7 @@ Optional properties: - rx-num-evt : FIFO levels. - sram-size-playback : size of sram to be allocated during playback - sram-size-capture : size of sram to be allocated during capture -- interrupts : Interrupt numbers for McASP, currently not used by the driver +- interrupts : Interrupt numbers for McASP - interrupt-names : Known interrupt names are "tx" and "rx" - pinctrl-0: Should specify pin control group used for this controller. - pinctrl-names: Should contain only one value - "default", for more details diff --git a/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt index 0d7985c864af..6dfa88c4dc1e 100644 --- a/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt +++ b/Documentation/devicetree/bindings/sound/eukrea-tlv320.txt @@ -1,11 +1,16 @@ Audio complex for Eukrea boards with tlv320aic23 codec. Required properties: -- compatible : "eukrea,asoc-tlv320" -- eukrea,model : The user-visible name of this sound complex. -- ssi-controller : The phandle of the SSI controller. -- fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX). -- fsl,mux-ext-port : The external port of the i.MX audio muxer. + + - compatible : "eukrea,asoc-tlv320" + + - eukrea,model : The user-visible name of this sound complex. + + - ssi-controller : The phandle of the SSI controller. + + - fsl,mux-int-port : The internal port of the i.MX audio muxer (AUDMUX). + + - fsl,mux-ext-port : The external port of the i.MX audio muxer. Note: The AUDMUX port numbering should start at 1, which is consistent with hardware manual. diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index 52f5b6bf3e8e..d3b6b5f48010 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -7,37 +7,39 @@ other DSPs. It has up to six transmitters and four receivers. Required properties: - - compatible : Compatible list, must contain "fsl,imx35-esai" or - "fsl,vf610-esai" + - compatible : Compatible list, must contain "fsl,imx35-esai" or + "fsl,vf610-esai" - - reg : Offset and length of the register set for the device. + - reg : Offset and length of the register set for the device. - - interrupts : Contains the spdif interrupt. + - interrupts : Contains the spdif interrupt. - - dmas : Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. - - dma-names : Two dmas have to be defined, "tx" and "rx". + - dma-names : Two dmas have to be defined, "tx" and "rx". - - clocks: Contains an entry for each entry in clock-names. + - clocks : Contains an entry for each entry in clock-names. - - clock-names : Includes the following entries: - "core" The core clock used to access registers - "extal" The esai baud clock for esai controller used to derive - HCK, SCK and FS. - "fsys" The system clock derived from ahb clock used to derive - HCK, SCK and FS. + - clock-names : Includes the following entries: + "core" The core clock used to access registers + "extal" The esai baud clock for esai controller used to + derive HCK, SCK and FS. + "fsys" The system clock derived from ahb clock used to + derive HCK, SCK and FS. - - fsl,fifo-depth: The number of elements in the transmit and receive FIFOs. - This number is the maximum allowed value for TFCR[TFWM] or RFCR[RFWM]. + - fsl,fifo-depth : The number of elements in the transmit and receive + FIFOs. This number is the maximum allowed value for + TFCR[TFWM] or RFCR[RFWM]. - fsl,esai-synchronous: This is a boolean property. If present, indicating - that ESAI would work in the synchronous mode, which means all the settings - for Receiving would be duplicated from Transmition related registers. + that ESAI would work in the synchronous mode, which + means all the settings for Receiving would be + duplicated from Transmition related registers. - - big-endian : If this property is absent, the native endian mode will - be in use as default, or the big endian mode will be in use for all the - device registers. + - big-endian : If this property is absent, the native endian mode + will be in use as default, or the big endian mode + will be in use for all the device registers. Example: diff --git a/Documentation/devicetree/bindings/sound/fsl,spdif.txt b/Documentation/devicetree/bindings/sound/fsl,spdif.txt index 3e9e82c8eab3..b5ee32ee3706 100644 --- a/Documentation/devicetree/bindings/sound/fsl,spdif.txt +++ b/Documentation/devicetree/bindings/sound/fsl,spdif.txt @@ -6,32 +6,31 @@ a fibre cable. Required properties: - - compatible : Compatible list, must contain "fsl,imx35-spdif". + - compatible : Compatible list, must contain "fsl,imx35-spdif". - - reg : Offset and length of the register set for the device. + - reg : Offset and length of the register set for the device. - - interrupts : Contains the spdif interrupt. + - interrupts : Contains the spdif interrupt. - - dmas : Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. - - dma-names : Two dmas have to be defined, "tx" and "rx". + - dma-names : Two dmas have to be defined, "tx" and "rx". - - clocks : Contains an entry for each entry in clock-names. + - clocks : Contains an entry for each entry in clock-names. - - clock-names : Includes the following entries: - "core" The core clock of spdif controller - "rxtx<0-7>" Clock source list for tx and rx clock. - This clock list should be identical to - the source list connecting to the spdif - clock mux in "SPDIF Transceiver Clock - Diagram" of SoC reference manual. It - can also be referred to TxClk_Source - bit of register SPDIF_STC. + - clock-names : Includes the following entries: + "core" The core clock of spdif controller. + "rxtx<0-7>" Clock source list for tx and rx clock. + This clock list should be identical to the source + list connecting to the spdif clock mux in "SPDIF + Transceiver Clock Diagram" of SoC reference manual. + It can also be referred to TxClk_Source bit of + register SPDIF_STC. - - big-endian : If this property is absent, the native endian mode will - be in use as default, or the big endian mode will be in use for all the - device registers. + - big-endian : If this property is absent, the native endian mode + will be in use as default, or the big endian mode + will be in use for all the device registers. Example: diff --git a/Documentation/devicetree/bindings/sound/fsl-sai.txt b/Documentation/devicetree/bindings/sound/fsl-sai.txt index 4956b14d4b06..044e5d76e2dd 100644 --- a/Documentation/devicetree/bindings/sound/fsl-sai.txt +++ b/Documentation/devicetree/bindings/sound/fsl-sai.txt @@ -5,32 +5,48 @@ which provides a synchronous audio interface that supports fullduplex serial interfaces with frame synchronization such as I2S, AC97, TDM, and codec/DSP interfaces. - Required properties: -- compatible: Compatible list, contains "fsl,vf610-sai" or "fsl,imx6sx-sai". -- reg: Offset and length of the register set for the device. -- clocks: Must contain an entry for each entry in clock-names. -- clock-names : Must include the "bus" for register access and "mclk1" "mclk2" - "mclk3" for bit clock and frame clock providing. -- dmas : Generic dma devicetree binding as described in - Documentation/devicetree/bindings/dma/dma.txt. -- dma-names : Two dmas have to be defined, "tx" and "rx". -- pinctrl-names: Must contain a "default" entry. -- pinctrl-NNN: One property must exist for each entry in pinctrl-names. - See ../pinctrl/pinctrl-bindings.txt for details of the property values. -- big-endian: Boolean property, required if all the FTM_PWM registers - are big-endian rather than little-endian. -- lsb-first: Configures whether the LSB or the MSB is transmitted first for - the fifo data. If this property is absent, the MSB is transmitted first as - default, or the LSB is transmitted first. -- fsl,sai-synchronous-rx: This is a boolean property. If present, indicating - that SAI will work in the synchronous mode (sync Tx with Rx) which means - both the transimitter and receiver will send and receive data by following - receiver's bit clocks and frame sync clocks. -- fsl,sai-asynchronous: This is a boolean property. If present, indicating - that SAI will work in the asynchronous mode, which means both transimitter - and receiver will send and receive data by following their own bit clocks - and frame sync clocks separately. + + - compatible : Compatible list, contains "fsl,vf610-sai" or + "fsl,imx6sx-sai". + + - reg : Offset and length of the register set for the device. + + - clocks : Must contain an entry for each entry in clock-names. + + - clock-names : Must include the "bus" for register access and + "mclk1", "mclk2", "mclk3" for bit clock and frame + clock providing. + - dmas : Generic dma devicetree binding as described in + Documentation/devicetree/bindings/dma/dma.txt. + + - dma-names : Two dmas have to be defined, "tx" and "rx". + + - pinctrl-names : Must contain a "default" entry. + + - pinctrl-NNN : One property must exist for each entry in + pinctrl-names. See ../pinctrl/pinctrl-bindings.txt + for details of the property values. + + - big-endian : Boolean property, required if all the FTM_PWM + registers are big-endian rather than little-endian. + + - lsb-first : Configures whether the LSB or the MSB is transmitted + first for the fifo data. If this property is absent, + the MSB is transmitted first as default, or the LSB + is transmitted first. + + - fsl,sai-synchronous-rx: This is a boolean property. If present, indicating + that SAI will work in the synchronous mode (sync Tx + with Rx) which means both the transimitter and the + receiver will send and receive data by following + receiver's bit clocks and frame sync clocks. + + - fsl,sai-asynchronous: This is a boolean property. If present, indicating + that SAI will work in the asynchronous mode, which + means both transimitter and receiver will send and + receive data by following their own bit clocks and + frame sync clocks separately. Note: - If both fsl,sai-asynchronous and fsl,sai-synchronous-rx are absent, the diff --git a/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt b/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt index e4acdd891e49..2f89db88fd57 100644 --- a/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/imx-audio-sgtl5000.txt @@ -1,33 +1,40 @@ Freescale i.MX audio complex with SGTL5000 codec Required properties: -- compatible : "fsl,imx-audio-sgtl5000" -- model : The user-visible name of this sound complex -- ssi-controller : The phandle of the i.MX SSI controller -- audio-codec : The phandle of the SGTL5000 audio codec -- audio-routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names could be power - supplies, SGTL5000 pins, and the jacks on the board: - - Power supplies: - * Mic Bias - - SGTL5000 pins: - * MIC_IN - * LINE_IN - * HP_OUT - * LINE_OUT - - Board connectors: - * Mic Jack - * Line In Jack - * Headphone Jack - * Line Out Jack - * Ext Spk - -- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) -- mux-ext-port : The external port of the i.MX audio muxer + + - compatible : "fsl,imx-audio-sgtl5000" + + - model : The user-visible name of this sound complex + + - ssi-controller : The phandle of the i.MX SSI controller + + - audio-codec : The phandle of the SGTL5000 audio codec + + - audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, SGTL5000 + pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + SGTL5000 pins: + * MIC_IN + * LINE_IN + * HP_OUT + * LINE_OUT + + Board connectors: + * Mic Jack + * Line In Jack + * Headphone Jack + * Line Out Jack + * Ext Spk + + - mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) + + - mux-ext-port : The external port of the i.MX audio muxer Note: The AUDMUX port numbering should start at 1, which is consistent with hardware manual. diff --git a/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt b/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt index 7d13479f9c3c..da84a442ccea 100644 --- a/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt +++ b/Documentation/devicetree/bindings/sound/imx-audio-spdif.txt @@ -2,23 +2,25 @@ Freescale i.MX audio complex with S/PDIF transceiver Required properties: - - compatible : "fsl,imx-audio-spdif" + - compatible : "fsl,imx-audio-spdif" - - model : The user-visible name of this sound complex + - model : The user-visible name of this sound complex - - spdif-controller : The phandle of the i.MX S/PDIF controller + - spdif-controller : The phandle of the i.MX S/PDIF controller Optional properties: - - spdif-out : This is a boolean property. If present, the transmitting - function of S/PDIF will be enabled, indicating there's a physical - S/PDIF out connector/jack on the board or it's connecting to some - other IP block, such as an HDMI encoder/display-controller. + - spdif-out : This is a boolean property. If present, the + transmitting function of S/PDIF will be enabled, + indicating there's a physical S/PDIF out connector + or jack on the board or it's connecting to some + other IP block, such as an HDMI encoder or + display-controller. - - spdif-in : This is a boolean property. If present, the receiving - function of S/PDIF will be enabled, indicating there's a physical - S/PDIF in connector/jack on the board. + - spdif-in : This is a boolean property. If present, the receiving + function of S/PDIF will be enabled, indicating there + is a physical S/PDIF in connector/jack on the board. * Note: At least one of these two properties should be set in the DT binding. diff --git a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt index f49450a87890..acea71bee34f 100644 --- a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt +++ b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt @@ -1,25 +1,32 @@ Freescale i.MX audio complex with WM8962 codec Required properties: -- compatible : "fsl,imx-audio-wm8962" -- model : The user-visible name of this sound complex -- ssi-controller : The phandle of the i.MX SSI controller -- audio-codec : The phandle of the WM8962 audio codec -- audio-routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the connection's sink, - the second being the connection's source. Valid names could be power - supplies, WM8962 pins, and the jacks on the board: - - Power supplies: - * Mic Bias - - Board connectors: - * Mic Jack - * Headphone Jack - * Ext Spk - -- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) -- mux-ext-port : The external port of the i.MX audio muxer + + - compatible : "fsl,imx-audio-wm8962" + + - model : The user-visible name of this sound complex + + - ssi-controller : The phandle of the i.MX SSI controller + + - audio-codec : The phandle of the WM8962 audio codec + + - audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's + source. Valid names could be power supplies, WM8962 + pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + Board connectors: + * Mic Jack + * Headphone Jack + * Ext Spk + + - mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) + + - mux-ext-port : The external port of the i.MX audio muxer Note: The AUDMUX port numbering should start at 1, which is consistent with hardware manual. diff --git a/Documentation/devicetree/bindings/sound/imx-audmux.txt b/Documentation/devicetree/bindings/sound/imx-audmux.txt index f88a00e54c63..b30a737e209e 100644 --- a/Documentation/devicetree/bindings/sound/imx-audmux.txt +++ b/Documentation/devicetree/bindings/sound/imx-audmux.txt @@ -1,18 +1,24 @@ Freescale Digital Audio Mux (AUDMUX) device Required properties: -- compatible : "fsl,imx21-audmux" for AUDMUX version firstly used on i.MX21, - or "fsl,imx31-audmux" for the version firstly used on i.MX31. -- reg : Should contain AUDMUX registers location and length + + - compatible : "fsl,imx21-audmux" for AUDMUX version firstly used + on i.MX21, or "fsl,imx31-audmux" for the version + firstly used on i.MX31. + + - reg : Should contain AUDMUX registers location and length. An initial configuration can be setup using child nodes. Required properties of optional child nodes: -- fsl,audmux-port : Integer of the audmux port that is configured by this - child node. -- fsl,port-config : List of configuration options for the specific port. For - imx31-audmux and above, it is a list of tuples <ptcr pdcr>. For - imx21-audmux it is a list of pcr values. + + - fsl,audmux-port : Integer of the audmux port that is configured by this + child node. + + - fsl,port-config : List of configuration options for the specific port. + For imx31-audmux and above, it is a list of tuples + <ptcr pdcr>. For imx21-audmux it is a list of pcr + values. Example: diff --git a/Documentation/devicetree/bindings/sound/max98090.txt b/Documentation/devicetree/bindings/sound/max98090.txt index c454e67f54bb..aa802a274520 100644 --- a/Documentation/devicetree/bindings/sound/max98090.txt +++ b/Documentation/devicetree/bindings/sound/max98090.txt @@ -16,6 +16,8 @@ Optional properties: - clock-names: Should be "mclk" +- maxim,dmic-freq: Frequency at which to clock DMIC + Pins on the device (for linking into audio routes): * MIC1 diff --git a/Documentation/devicetree/bindings/sound/renesas,fsi.txt b/Documentation/devicetree/bindings/sound/renesas,fsi.txt index c5be003f413e..0d0ab51105b0 100644 --- a/Documentation/devicetree/bindings/sound/renesas,fsi.txt +++ b/Documentation/devicetree/bindings/sound/renesas,fsi.txt @@ -1,11 +1,16 @@ Renesas FSI Required properties: -- compatible : "renesas,sh_fsi2" or "renesas,sh_fsi" +- compatible : "renesas,fsi2-<soctype>", + "renesas,sh_fsi2" or "renesas,sh_fsi" as + fallback. + Examples with soctypes are: + - "renesas,fsi2-r8a7740" (R-Mobile A1) + - "renesas,fsi2-sh73a0" (SH-Mobile AG5) - reg : Should contain the register physical address and length - interrupts : Should contain FSI interrupt -- fsia,spdif-connection : FSI is connected by S/PDFI +- fsia,spdif-connection : FSI is connected by S/PDIF - fsia,stream-mode-support : FSI supports 16bit stream mode. - fsia,use-internal-clock : FSI uses internal clock when master mode. diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index aa697abf337e..2dd690bc19cc 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -1,8 +1,12 @@ Renesas R-Car sound Required properties: -- compatible : "renesas,rcar_sound-gen1" if generation1 +- compatible : "renesas,rcar_sound-<soctype>", fallbacks + "renesas,rcar_sound-gen1" if generation1, and "renesas,rcar_sound-gen2" if generation2 + Examples with soctypes are: + - "renesas,rcar_sound-r8a7790" (R-Car H2) + - "renesas,rcar_sound-r8a7791" (R-Car M2-W) - reg : Should contain the register physical address. required register is SRU/ADG/SSI if generation1 @@ -35,9 +39,9 @@ DAI subnode properties: Example: -rcar_sound: rcar_sound@0xffd90000 { +rcar_sound: rcar_sound@ec500000 { #sound-dai-cells = <1>; - compatible = "renesas,rcar_sound-gen2"; + compatible = "renesas,rcar_sound-r8a7791", "renesas,rcar_sound-gen2"; reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ diff --git a/Documentation/devicetree/bindings/sound/rt5631.txt b/Documentation/devicetree/bindings/sound/rt5631.txt new file mode 100644 index 000000000000..92b986ca337b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5631.txt @@ -0,0 +1,48 @@ +ALC5631/RT5631 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "realtek,alc5631" or "realtek,rt5631" + + - reg : the I2C address of the device. + +Pins on the device (for linking into audio routes): + + * SPK_OUT_R_P + * SPK_OUT_R_N + * SPK_OUT_L_P + * SPK_OUT_L_N + * HP_OUT_L + * HP_OUT_R + * AUX_OUT2_LP + * AUX_OUT2_RN + * AUX_OUT1_LP + * AUX_OUT1_RN + * AUX_IN_L_JD + * AUX_IN_R_JD + * MONO_IN_P + * MONO_IN_N + * MIC1_P + * MIC1_N + * MIC2_P + * MIC2_N + * MONO_OUT_P + * MONO_OUT_N + * MICBIAS1 + * MICBIAS2 + +Example: + +alc5631: alc5631@1a { + compatible = "realtek,alc5631"; + reg = <0x1a>; +}; + +or + +rt5631: rt5631@1a { + compatible = "realtek,rt5631"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5677.txt b/Documentation/devicetree/bindings/sound/rt5677.txt index 0701b834fc73..740ff771aa8b 100644 --- a/Documentation/devicetree/bindings/sound/rt5677.txt +++ b/Documentation/devicetree/bindings/sound/rt5677.txt @@ -27,6 +27,21 @@ Optional properties: Boolean. Indicate MIC1/2 input and LOUT1/2/3 outputs are differential, rather than single-ended. +- realtek,gpio-config + Array of six 8bit elements that configures GPIO. + 0 - floating (reset value) + 1 - pull down + 2 - pull up + +- realtek,jd1-gpio + Configures GPIO Mic Jack detection 1. + Select 0 ~ 3 as OFF, GPIO1, GPIO2 and GPIO3 respectively. + +- realtek,jd2-gpio +- realtek,jd3-gpio + Configures GPIO Mic Jack detection 2 and 3. + Select 0 ~ 3 as OFF, GPIO4, GPIO5 and GPIO6 respectively. + Pins on the device (for linking into audio routes): * IN1P @@ -56,4 +71,6 @@ rt5677 { realtek,pow-ldo2-gpio = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; realtek,in1-differential = "true"; + realtek,gpio-config = /bits/ 8 <0 0 0 0 0 2>; /* pull up GPIO6 */ + realtek,jd2-gpio = <3>; /* Enables Jack detection for GPIO6 */ }; diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt index 7386d444ada1..d188296bb6ec 100644 --- a/Documentation/devicetree/bindings/sound/samsung-i2s.txt +++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt @@ -6,10 +6,17 @@ Required SoC Specific Properties: - samsung,s3c6410-i2s: for 8/16/24bit stereo I2S. - samsung,s5pv210-i2s: for 8/16/24bit multichannel(5.1) I2S with secondary fifo, s/w reset control and internal mux for root clk src. - - samsung,exynos5420-i2s: for 8/16/24bit multichannel(7.1) I2S with - secondary fifo, s/w reset control, internal mux for root clk src and - TDM support. TDM (Time division multiplexing) is to allow transfer of - multiple channel audio data on single data line. + - samsung,exynos5420-i2s: for 8/16/24bit multichannel(5.1) I2S for + playback, sterio channel capture, secondary fifo using internal + or external dma, s/w reset control, internal mux for root clk src + and 7.1 channel TDM support for playback. TDM (Time division multiplexing) + is to allow transfer of multiple channel audio data on single data line. + - samsung,exynos7-i2s: with all the available features of exynos5 i2s, + exynos7 I2S has 7.1 channel TDM support for capture, secondary fifo + with only external dma and more no.of root clk sampling frequencies. + - samsung,exynos7-i2s1: I2S1 on previous samsung platforms supports + stereo channels. exynos7 i2s1 upgraded to 5.1 multichannel with + slightly modified bit offsets. - reg: physical base address of the controller and length of memory mapped region. diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 955df60a118c..0e5e4eb3ef1b 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -7,10 +7,33 @@ Required properties: - clocks : the clock provider of SYS_MCLK +- micbias-resistor-k-ohms : the bias resistor to be used in kOmhs + The resistor can take values of 2k, 4k or 8k. + If set to 0 it will be off. + If this node is not mentioned or if the value is unknown, then + micbias resistor is set to 4K. + +- micbias-voltage-m-volts : the bias voltage to be used in mVolts + The voltage can take values from 1.25V to 3V by 250mV steps + If this node is not mentionned or the value is unknown, then + the value is set to 1.25V. + +- VDDA-supply : the regulator provider of VDDA + +- VDDIO-supply: the regulator provider of VDDIO + +Optional properties: + +- VDDD-supply : the regulator provider of VDDD + Example: codec: sgtl5000@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; clocks = <&clks 150>; + micbias-resistor-k-ohms = <2>; + micbias-voltage-m-volts = <2250>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; }; diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt index 042a0273b8ba..b7ba01ad1426 100644 --- a/Documentation/devicetree/bindings/submitting-patches.txt +++ b/Documentation/devicetree/bindings/submitting-patches.txt @@ -12,6 +12,9 @@ I. For patch submitters devicetree@vger.kernel.org + 3) The Documentation/ portion of the patch should come in the series before + the code implementing the binding. + II. For kernel maintainers 1) If you aren't comfortable reviewing a given binding, reply to it and ask diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.txt b/Documentation/devicetree/bindings/thermal/imx-thermal.txt index 1f0f67234a91..3c67bd50aa10 100644 --- a/Documentation/devicetree/bindings/thermal/imx-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.txt @@ -1,7 +1,10 @@ * Temperature Monitor (TEMPMON) on Freescale i.MX SoCs Required properties: -- compatible : "fsl,imx6q-thermal" +- compatible : "fsl,imx6q-tempmon" for i.MX6Q, "fsl,imx6sx-tempmon" for i.MX6SX. + i.MX6SX has two more IRQs than i.MX6Q, one is IRQ_LOW and the other is IRQ_PANIC, + when temperature is below than low threshold, IRQ_LOW will be triggered, when temperature + is higher than panic threshold, system will auto reboot by SRC module. - fsl,tempmon : phandle pointer to system controller that contains TEMPMON control registers, e.g. ANATOP on imx6q. - fsl,tempmon-data : phandle pointer to fuse controller that contains TEMPMON diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 0ef00be44b01..43404b197933 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -7,7 +7,10 @@ Required properties: - "renesas,thermal-r8a73a4" (R-Mobile AP6) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - - "renesas,thermal-r8a7791" (R-Car M2) + - "renesas,thermal-r8a7791" (R-Car M2-W) + - "renesas,thermal-r8a7792" (R-Car V2H) + - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a7794" (R-Car E2) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 723999d73744..a344ec2713a5 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -34,6 +34,7 @@ chipidea Chipidea, Inc chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. cirrus Cirrus Logic, Inc. +cnm Chips&Media, Inc. cortina Cortina Systems, Inc. crystalfontz Crystalfontz America, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) @@ -92,6 +93,7 @@ maxim Maxim Integrated Products mediatek MediaTek Inc. micrel Micrel Inc. microchip Microchip Technology Inc. +micron Micron Technology Inc. mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa @@ -127,6 +129,7 @@ renesas Renesas Electronics Corporation ricoh Ricoh Co. Ltd. rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor +sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler seagate Seagate Technology PLC @@ -138,7 +141,7 @@ silergy Silergy Corp. sirf SiRF Technology, Inc. sitronix Sitronix Technology Corporation smsc Standard Microsystems Corporation -snps Synopsys, Inc. +snps Synopsys, Inc. solidrun SolidRun sony Sony Corporation spansion Spansion Inc. diff --git a/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt new file mode 100644 index 000000000000..c3a36ee45552 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/cadence-wdt.txt @@ -0,0 +1,24 @@ +Zynq Watchdog Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Should be "cdns,wdt-r1p2". +- clocks : This is pclk (APB clock). +- interrupts : This is wd_irq - watchdog timeout interrupt. +- interrupt-parent : Must be core interrupt controller. + +Optional properties +- reset-on-timeout : If this property exists, then a reset is done + when watchdog times out. +- timeout-sec : Watchdog timeout value (in seconds). + +Example: + watchdog@f8005000 { + compatible = "cdns,wdt-r1p2"; + clocks = <&clkc 45>; + interrupt-parent = <&intc>; + interrupts = <0 9 1>; + reg = <0xf8005000 0x1000>; + reset-on-timeout; + timeout-sec = <10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt index e52ba2da868c..8dab6fd024aa 100644 --- a/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.txt @@ -7,7 +7,8 @@ Required properties: Optional property: - big-endian: If present the watchdog device's registers are implemented - in big endian mode, otherwise in little mode. + in big endian mode, otherwise in native mode(same with CPU), for more + detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. Examples: diff --git a/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt new file mode 100644 index 000000000000..9200fc2d508c --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/meson6-wdt.txt @@ -0,0 +1,13 @@ +Meson SoCs Watchdog timer + +Required properties: + +- compatible : should be "amlogic,meson6-wdt" +- reg : Specifies base physical address and size of the registers. + +Example: + +wdt: watchdog@c1109900 { + compatible = "amlogic,meson6-wdt"; + reg = <0xc1109900 0x8>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt new file mode 100644 index 000000000000..4726924d034e --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.txt @@ -0,0 +1,24 @@ +Qualcomm Krait Processor Sub-system (KPSS) Watchdog +--------------------------------------------------- + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,kpss-wdt-msm8960" + "qcom,kpss-wdt-apq8064" + "qcom,kpss-wdt-ipq8064" + +- reg : shall contain base register location and length +- clocks : shall contain the input clock + +Optional properties : +- timeout-sec : shall contain the default watchdog timeout in seconds, + if unset, the default timeout is 30 seconds + +Example: + watchdog@208a038 { + compatible = "qcom,kpss-wdt-ipq8064"; + reg = <0x0208a038 0x40>; + clocks = <&sleep_clk>; + timeout-sec = <10>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index cfff37511aac..8f3d96af81d7 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -9,6 +9,7 @@ Required properties: (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs (b) "samsung,exynos5250-wdt" for Exynos5250 (c) "samsung,exynos5420-wdt" for Exynos5420 + (c) "samsung,exynos7-wdt" for Exynos7 - reg : base physical address of the controller and length of memory mapped region. |