diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
3 files changed, 111 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt new file mode 100644 index 000000000000..515b2f9542e5 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt @@ -0,0 +1,42 @@ +* Synopsys DesignWare PCIe root complex in ECAM shift mode + +In some cases, firmware may already have configured the Synopsys DesignWare +PCIe controller in RC mode with static ATU window mappings that cover all +config, MMIO and I/O spaces in a [mostly] ECAM compatible fashion. +In this case, there is no need for the OS to perform any low level setup +of clocks, PHYs or device registers, nor is there any reason for the driver +to reconfigure ATU windows for config and/or IO space accesses at runtime. + +In cases where the IP was synthesized with a minimum ATU window size of +64 KB, it cannot be supported by the generic ECAM driver, because it +requires special config space accessors that filter accesses to device #1 +and beyond on the first bus. + +Required properties: +- compatible: "marvell,armada8k-pcie-ecam" or + "socionext,synquacer-pcie-ecam" or + "snps,dw-pcie-ecam" (must be preceded by a more specific match) + +Please refer to the binding document of "pci-host-ecam-generic" in the +file host-generic-pci.txt for a description of the remaining required +and optional properties. + +Example: + + pcie1: pcie@7f000000 { + compatible = "socionext,synquacer-pcie-ecam", "snps,dw-pcie-ecam"; + device_type = "pci"; + reg = <0x0 0x7f000000 0x0 0xf00000>; + bus-range = <0x0 0xe>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x1000000 0x00 0x00010000 0x00 0x7ff00000 0x0 0x00010000>, + <0x2000000 0x00 0x70000000 0x00 0x70000000 0x0 0x0f000000>, + <0x3000000 0x3f 0x00000000 0x3f 0x00000000 0x1 0x00000000>; + + #interrupt-cells = <0x1>; + interrupt-map-mask = <0x0 0x0 0x0 0x0>; + interrupt-map = <0x0 0x0 0x0 0x0 &gic 0x0 0x0 0x0 182 0x4>; + msi-map = <0x0 &its 0x0 0x10000>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt new file mode 100644 index 000000000000..c84bc027930b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt @@ -0,0 +1,68 @@ +HiSilicon STB PCIe host bridge DT description + +The HiSilicon STB PCIe host controller is based on the DesignWare PCIe core. +It shares common functions with the DesignWare PCIe core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Additional properties are described here: + +Required properties +- compatible: Should be one of the following strings: + "hisilicon,hi3798cv200-pcie" +- reg: Should contain sysctl, rc_dbi, config registers location and length. +- reg-names: Must include the following entries: + "control": control registers of PCIe controller; + "rc-dbi": configuration space of PCIe controller; + "config": configuration transaction space of PCIe controller. +- bus-range: PCI bus numbers covered. +- interrupts: MSI interrupt. +- interrupt-names: Must include "msi" entries. +- clocks: List of phandle and clock specifier pairs as listed in clock-names + property. +- clock-name: Must include the following entries: + "aux": auxiliary gate clock; + "pipe": pipe gate clock; + "sys": sys gate clock; + "bus": bus gate clock. +- resets: List of phandle and reset specifier pairs as listed in reset-names + property. +- reset-names: Must include the following entries: + "soft": soft reset; + "sys": sys reset; + "bus": bus reset. + +Optional properties: +- reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal. +- phys: List of phandle and phy mode specifier, should be 0. +- phy-names: Must be "phy". + +Example: + pcie@f9860000 { + compatible = "hisilicon,hi3798cv200-pcie"; + reg = <0xf9860000 0x1000>, + <0xf0000000 0x2000>, + <0xf2000000 0x01000000>; + reg-names = "control", "rc-dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0 15>; + num-lanes = <1>; + ranges=<0x81000000 0 0 0xf4000000 0 0x00010000 + 0x82000000 0 0xf3000000 0xf3000000 0 0x01000000>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg PCIE_AUX_CLK>, + <&crg PCIE_PIPE_CLK>, + <&crg PCIE_SYS_CLK>, + <&crg PCIE_BUS_CLK>; + clock-names = "aux", "pipe", "sys", "bus"; + resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>; + reset-names = "soft", "sys", "bus"; + phys = <&combphy1 PHY_TYPE_PCIE>; + phy-names = "phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index c0484da0f20d..66df1e81e0b8 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -18,6 +18,7 @@ Required properties: "fsl,ls2088a-pcie" "fsl,ls1088a-pcie" "fsl,ls1046a-pcie" + "fsl,ls1012a-pcie" - reg: base addresses and lengths of the PCIe controller register blocks. - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. |