1 files changed, 0 insertions, 154 deletions
diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
deleted file mode 100644
index c06863badfbd..000000000000
--- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
+++ /dev/null
@@ -1,154 +0,0 @@
-Binding for Qualcomm Technologies, Inc. WLED driver
-
-WLED (White Light Emitting Diode) driver is used for controlling display
-backlight that is part of PMIC on Qualcomm Technologies, Inc. reference
-platforms. The PMIC is connected to the host processor via SPMI bus.
-
-- compatible
-	Usage:        required
-	Value type:   <string>
-	Definition:   should be one of:
-			"qcom,pm8941-wled"
-			"qcom,pmi8998-wled"
-			"qcom,pm660l-wled"
-
-- reg
-	Usage:        required
-	Value type:   <prop encoded array>
-	Definition:   Base address of the WLED modules.
-
-- default-brightness
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   brightness value on boot, value from: 0-4095.
-		      Default: 2048
-
-- label
-	Usage:        required
-	Value type:   <string>
-	Definition:   The name of the backlight device
-
-- qcom,cs-out
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   enable current sink output.
-		      This property is supported only for PM8941.
-
-- qcom,cabc
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   enable content adaptive backlight control.
-
-- qcom,ext-gen
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   use externally generated modulator signal to dim.
-		      This property is supported only for PM8941.
-
-- qcom,current-limit
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   mA; per-string current limit; value from 0 to 25 with
-		      1 mA step. Default 20 mA.
-		      This property is supported only for pm8941.
-
-- qcom,current-limit-microamp
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   uA; per-string current limit; value from 0 to 30000 with
-		      2500 uA step. Default 25 mA.
-
-- qcom,current-boost-limit
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   mA; boost current limit.
-		      For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400,
-		      1680. Default: 805 mA.
-		      For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300,
-		      1500. Default: 970 mA.
-
-- qcom,switching-freq
-	Usage:        optional
-	Value type:   <u32>
-	 Definition:   kHz; switching frequency; one of: 600, 640, 685, 738,
-		       800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200,
-		       4800, 9600.
-		       Default: for pm8941: 1600 kHz
-				for pmi8998: 800 kHz
-
-- qcom,ovp
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   V; Over-voltage protection limit; one of:
-		      27, 29, 32, 35. Default: 29V
-		      This property is supported only for PM8941.
-
-- qcom,ovp-millivolt
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   mV; Over-voltage protection limit;
-		      For pmi8998: one of 18100, 19600, 29600, 31100.
-		      Default 29600 mV.
-		      If this property is not specified for PM8941, it
-		      falls back to "qcom,ovp" property.
-
-- qcom,num-strings
-	Usage:        optional
-	Value type:   <u32>
-	Definition:   #; number of led strings attached;
-		      value: For PM8941 from 1 to 3. Default: 2
-			     For PMI8998 from 1 to 4.
-
-- interrupts
-	Usage:        optional
-	Value type:   <prop encoded array>
-	Definition:   Interrupts associated with WLED. This should be
-		      "short" and "ovp" interrupts. Interrupts can be
-		      specified as per the encoding listed under
-		      Documentation/devicetree/bindings/spmi/
-		      qcom,spmi-pmic-arb.txt.
-
-- interrupt-names
-	Usage:        optional
-	Value type:   <string>
-	Definition:   Interrupt names associated with the interrupts.
-		      Must be "short" and "ovp". The short circuit detection
-		      is not supported for PM8941.
-
-- qcom,enabled-strings
-	Usage:        optional
-	Value tyoe:   <u32 array>
-	Definition:   Array of the WLED strings numbered from 0 to 3. Each
-		      string of leds are operated individually. Specify the
-		      list of strings used by the device. Any combination of
-		      led strings can be used.
-
-- qcom,external-pfet
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   Specify if external PFET control for short circuit
-		      protection is used. This property is supported only
-		      for PMI8998.
-
-- qcom,auto-string-detection
-	Usage:        optional
-	Value type:   <bool>
-	Definition:   Enables auto-detection of the WLED string configuration.
-		      This feature is not supported for PM8941.
-
-
-Example:
-
-pm8941-wled@d800 {
-	compatible = "qcom,pm8941-wled";
-	reg = <0xd800>;
-	label = "backlight";
-
-	qcom,cs-out;
-	qcom,current-limit = <20>;
-	qcom,current-boost-limit = <805>;
-	qcom,switching-freq = <1600>;
-	qcom,ovp = <29>;
-	qcom,num-strings = <2>;
-	qcom,enabled-strings = <0 1>;
-};