diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
-rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio-mvebu.txt | 6 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio_atmel.txt | 10 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/gpio/ingenic,gpio.txt | 46 |
3 files changed, 57 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt index 2c5304ff467c..38ca2201e8ae 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt @@ -51,9 +51,9 @@ Required properties: Optional properties: In order to use the GPIO lines in PWM mode, some additional optional -properties are required. Only Armada 370 and XP support these properties. +properties are required. -- compatible: Must contain "marvell,armada-370-xp-gpio" +- compatible: Must contain "marvell,armada-370-gpio" - reg: an additional register set is needed, for the GPIO Blink Counter on/off registers. @@ -81,7 +81,7 @@ Example: }; gpio1: gpio@18140 { - compatible = "marvell,armada-370-xp-gpio"; + compatible = "marvell,armada-370-gpio"; reg = <0x18140 0x40>, <0x181c8 0x08>; reg-names = "gpio", "pwm"; ngpios = <17>; diff --git a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt index 85f8c0d084fa..29416f9c3220 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_atmel.txt +++ b/Documentation/devicetree/bindings/gpio/gpio_atmel.txt @@ -5,9 +5,13 @@ Required properties: - reg: Should contain GPIO controller registers location and length - interrupts: Should be the port interrupt shared by all the pins. - #gpio-cells: Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify optional parameters to declare if the GPIO + is active high or low. See gpio.txt. - gpio-controller: Marks the device node as a GPIO controller. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. The first cell is the pin number and the + second cell is used to specify irq type flags, see the two cell description + in interrupt-controller/interrupts.txt for details. optional properties: - #gpio-lines: Number of gpio if absent 32. @@ -21,5 +25,7 @@ Example: #gpio-cells = <2>; gpio-controller; #gpio-lines = <19>; + interrupt-controller; + #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt b/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt new file mode 100644 index 000000000000..7988aeb725f4 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/ingenic,gpio.txt @@ -0,0 +1,46 @@ +Ingenic jz47xx GPIO controller + +That the Ingenic GPIO driver node must be a sub-node of the Ingenic pinctrl +driver node. + +Required properties: +-------------------- + + - compatible: Must contain one of: + - "ingenic,jz4740-gpio" + - "ingenic,jz4770-gpio" + - "ingenic,jz4780-gpio" + - reg: The GPIO bank number. + - interrupt-controller: Marks the device node as an interrupt controller. + - interrupts: Interrupt specifier for the controllers interrupt. + - #interrupt-cells: Should be 2. Refer to + ../interrupt-controller/interrupts.txt for more details. + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + - gpio-ranges: Range of pins managed by the GPIO controller. Refer to + 'gpio.txt' in this directory for more details. + +Example: +-------- + +&pinctrl { + #address-cells = <1>; + #size-cells = <0>; + + gpa: gpio@0 { + compatible = "ingenic,jz4740-gpio"; + reg = <0>; + + gpio-controller; + gpio-ranges = <&pinctrl 0 0 32>; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&intc>; + interrupts = <28>; + }; +}; |