diff options
| -rw-r--r-- | drivers/iio/adc/at91-sama5d2_adc.c | 142 |
1 files changed, 72 insertions, 70 deletions
diff --git a/drivers/iio/adc/at91-sama5d2_adc.c b/drivers/iio/adc/at91-sama5d2_adc.c index 77a7169a2759..60f7aef906e0 100644 --- a/drivers/iio/adc/at91-sama5d2_adc.c +++ b/drivers/iio/adc/at91-sama5d2_adc.c @@ -728,7 +728,6 @@ static int at91_adc_configure_trigger(struct iio_trigger *trig, bool state) struct iio_dev *indio = iio_trigger_get_drvdata(trig); struct at91_adc_state *st = iio_priv(indio); u32 status = at91_adc_readl(st, AT91_SAMA5D2_TRGR); - u8 bit; /* clear TRGMOD */ status &= ~AT91_SAMA5D2_TRGR_TRGMOD_MASK; @@ -739,48 +738,6 @@ static int at91_adc_configure_trigger(struct iio_trigger *trig, bool state) /* set/unset hw trigger */ at91_adc_writel(st, AT91_SAMA5D2_TRGR, status); - for_each_set_bit(bit, indio->active_scan_mask, indio->num_channels) { - struct iio_chan_spec const *chan = at91_adc_chan_get(indio, bit); - u32 cor; - - if (!chan) - continue; - /* these channel types cannot be handled by this trigger */ - if (chan->type == IIO_POSITIONRELATIVE || - chan->type == IIO_PRESSURE) - continue; - - if (state) { - cor = at91_adc_readl(st, AT91_SAMA5D2_COR); - - if (chan->differential) - cor |= (BIT(chan->channel) | - BIT(chan->channel2)) << - AT91_SAMA5D2_COR_DIFF_OFFSET; - else - cor &= ~(BIT(chan->channel) << - AT91_SAMA5D2_COR_DIFF_OFFSET); - - at91_adc_writel(st, AT91_SAMA5D2_COR, cor); - } - - if (state) - at91_adc_writel(st, AT91_SAMA5D2_CHER, - BIT(chan->channel)); - else - at91_adc_writel(st, AT91_SAMA5D2_CHDR, - BIT(chan->channel)); - } - - /* Nothing to do if using DMA */ - if (st->dma_st.dma_chan) - return 0; - - if (state) - at91_adc_writel(st, AT91_SAMA5D2_IER, AT91_SAMA5D2_IER_DRDY); - else - at91_adc_writel(st, AT91_SAMA5D2_IDR, AT91_SAMA5D2_IER_DRDY); - return 0; } @@ -905,9 +862,22 @@ static int at91_adc_dma_start(struct iio_dev *indio_dev) return 0; } +static bool at91_adc_buffer_check_use_irq(struct iio_dev *indio, + struct at91_adc_state *st) +{ + /* if using DMA, we do not use our own IRQ (we use DMA-controller) */ + if (st->dma_st.dma_chan) + return false; + /* if the trigger is not ours, then it has its own IRQ */ + if (iio_trigger_validate_own_device(indio->trig, indio)) + return false; + return true; +} + static int at91_adc_buffer_postenable(struct iio_dev *indio_dev) { int ret; + u8 bit; struct at91_adc_state *st = iio_priv(indio_dev); /* check if we are enabling triggered buffer or the touchscreen */ @@ -928,6 +898,36 @@ static int at91_adc_buffer_postenable(struct iio_dev *indio_dev) return ret; } + for_each_set_bit(bit, indio_dev->active_scan_mask, + indio_dev->num_channels) { + struct iio_chan_spec const *chan = + at91_adc_chan_get(indio_dev, bit); + u32 cor; + + if (!chan) + continue; + /* these channel types cannot be handled by this trigger */ + if (chan->type == IIO_POSITIONRELATIVE || + chan->type == IIO_PRESSURE) + continue; + + cor = at91_adc_readl(st, AT91_SAMA5D2_COR); + + if (chan->differential) + cor |= (BIT(chan->channel) | BIT(chan->channel2)) << + AT91_SAMA5D2_COR_DIFF_OFFSET; + else + cor &= ~(BIT(chan->channel) << + AT91_SAMA5D2_COR_DIFF_OFFSET); + + at91_adc_writel(st, AT91_SAMA5D2_COR, cor); + + at91_adc_writel(st, AT91_SAMA5D2_CHER, BIT(chan->channel)); + } + + if (at91_adc_buffer_check_use_irq(indio_dev, st)) + at91_adc_writel(st, AT91_SAMA5D2_IER, AT91_SAMA5D2_IER_DRDY); + return iio_triggered_buffer_postenable(indio_dev); } @@ -948,21 +948,11 @@ static int at91_adc_buffer_predisable(struct iio_dev *indio_dev) if (!(indio_dev->currentmode & INDIO_ALL_TRIGGERED_MODES)) return -EINVAL; - /* continue with the triggered buffer */ - ret = iio_triggered_buffer_predisable(indio_dev); - if (ret < 0) - dev_err(&indio_dev->dev, "buffer predisable failed\n"); - - if (!st->dma_st.dma_chan) - return ret; - - /* if we are using DMA we must clear registers and end DMA */ - dmaengine_terminate_sync(st->dma_st.dma_chan); - /* - * For each enabled channel we must read the last converted value + * For each enable channel we must disable it in hardware. + * In the case of DMA, we must read the last converted value * to clear EOC status and not get a possible interrupt later. - * This value is being read by DMA from LCDR anyway + * This value is being read by DMA from LCDR anyway, so it's not lost. */ for_each_set_bit(bit, indio_dev->active_scan_mask, indio_dev->num_channels) { @@ -975,12 +965,28 @@ static int at91_adc_buffer_predisable(struct iio_dev *indio_dev) if (chan->type == IIO_POSITIONRELATIVE || chan->type == IIO_PRESSURE) continue; + + at91_adc_writel(st, AT91_SAMA5D2_CHDR, BIT(chan->channel)); + if (st->dma_st.dma_chan) at91_adc_readl(st, chan->address); } + if (at91_adc_buffer_check_use_irq(indio_dev, st)) + at91_adc_writel(st, AT91_SAMA5D2_IDR, AT91_SAMA5D2_IER_DRDY); + /* read overflow register to clear possible overflow status */ at91_adc_readl(st, AT91_SAMA5D2_OVER); + + /* continue with the triggered buffer */ + ret = iio_triggered_buffer_predisable(indio_dev); + if (ret < 0) + dev_err(&indio_dev->dev, "buffer predisable failed\n"); + + /* if we are using DMA we must clear registers and end DMA */ + if (st->dma_st.dma_chan) + dmaengine_terminate_sync(st->dma_st.dma_chan); + return ret; } @@ -1135,6 +1141,13 @@ static irqreturn_t at91_adc_trigger_handler(int irq, void *p) struct iio_dev *indio_dev = pf->indio_dev; struct at91_adc_state *st = iio_priv(indio_dev); + /* + * If it's not our trigger, start a conversion now, as we are + * actually polling the trigger now. + */ + if (iio_trigger_validate_own_device(indio_dev->trig, indio_dev)) + at91_adc_writel(st, AT91_SAMA5D2_CR, AT91_SAMA5D2_CR_START); + if (st->dma_st.dma_chan) at91_adc_trigger_handler_dma(indio_dev); else @@ -1147,20 +1160,9 @@ static irqreturn_t at91_adc_trigger_handler(int irq, void *p) static int at91_adc_buffer_init(struct iio_dev *indio) { - struct at91_adc_state *st = iio_priv(indio); - - if (st->selected_trig->hw_trig) { - return devm_iio_triggered_buffer_setup(&indio->dev, indio, - &iio_pollfunc_store_time, - &at91_adc_trigger_handler, &at91_buffer_setup_ops); - } - /* - * we need to prepare the buffer ops in case we will get - * another buffer attached (like a callback buffer for the touchscreen) - */ - indio->setup_ops = &at91_buffer_setup_ops; - - return 0; + return devm_iio_triggered_buffer_setup(&indio->dev, indio, + &iio_pollfunc_store_time, + &at91_adc_trigger_handler, &at91_buffer_setup_ops); } static unsigned at91_adc_startup_time(unsigned startup_time_min, |