Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Pull networking fixes from David Miller:
 "Fixes here and there, a couple new device IDs, as usual:

   1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei.

   2) Fix 64-bit division in iwlwifi, from Arnd Bergmann.

   3) Fix documentation for some eBPF helpers, from Quentin Monnet.

   4) Some UAPI bpf header sync with tools, also from Quentin Monnet.

   5) Set descriptor ownership bit at the right time for jumbo frames in
      stmmac driver, from Aaro Koskinen.

   6) Set IFF_UP properly in tun driver, from Eric Dumazet.

   7) Fix load/store doubleword instruction generation in powerpc eBPF
      JIT, from Naveen N. Rao.

   8) nla_nest_start() return value checks all over, from Kangjie Lu.

   9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this
      merge window. From Marcelo Ricardo Leitner and Xin Long.

  10) Fix memory corruption with large MTUs in stmmac, from Aaro
      Koskinen.

  11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric
      Dumazet.

  12) Fix topology subscription cancellation in tipc, from Erik Hugne.

  13) Memory leak in genetlink error path, from Yue Haibing.

  14) Valid control actions properly in packet scheduler, from Davide
      Caratti.

  15) Even if we get EEXIST, we still need to rehash if a shrink was
      delayed. From Herbert Xu.

  16) Fix interrupt mask handling in interrupt handler of r8169, from
      Heiner Kallweit.

  17) Fix leak in ehea driver, from Wen Yang"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits)
  dpaa2-eth: fix race condition with bql frame accounting
  chelsio: use BUG() instead of BUG_ON(1)
  net: devlink: skip info_get op call if it is not defined in dumpit
  net: phy: bcm54xx: Encode link speed and activity into LEDs
  tipc: change to check tipc_own_id to return in tipc_net_stop
  net: usb: aqc111: Extend HWID table by QNAP device
  net: sched: Kconfig: update reference link for PIE
  net: dsa: qca8k: extend slave-bus implementations
  net: dsa: qca8k: remove leftover phy accessors
  dt-bindings: net: dsa: qca8k: support internal mdio-bus
  dt-bindings: net: dsa: qca8k: fix example
  net: phy: don't clear BMCR in genphy_soft_reset
  bpf, libbpf: clarify bump in libbpf version info
  bpf, libbpf: fix version info and add it to shared object
  rxrpc: avoid clang -Wuninitialized warning
  tipc: tipc clang warning
  net: sched: fix cleanup NULL pointer exception in act_mirr
  r8169: fix cable re-plugging issue
  net: ethernet: ti: fix possible object reference leak
  net: ibm: fix possible object reference leak
  ...

1 files changed, 66 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
index bbcb255c3150..93a7469e70d4 100644
--- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt
+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt
@@ -12,10 +12,15 @@ Required properties:
 Subnodes:
 
 The integrated switch subnode should be specified according to the binding
-described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of
-port and PHY id, each subnode describing a port needs to have a valid phandle
-referencing the internal PHY connected to it. The CPU port of this switch is
-always port 0.
+described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external
+mdio-bus each subnode describing a port needs to have a valid phandle
+referencing the internal PHY it is connected to. This is because there's no
+N:N mapping of port and PHY id.
+
+Don't use mixed external and internal mdio-bus configurations, as this is
+not supported by the hardware.
+
+The CPU port of this switch is always port 0.
 
 A CPU port node has the following optional node:
 
@@ -31,8 +36,9 @@ For QCA8K the 'fixed-link' sub-node supports only the following properties:
 - 'full-duplex' (boolean, optional), to indicate that full duplex is
   used. When absent, half duplex is assumed.
 
-Example:
+Examples:
 
+for the external mdio-bus configuration:
 
 	&mdio0 {
 		phy_port1: phy@0 {
@@ -55,12 +61,12 @@ Example:
 			reg = <4>;
 		};
 
-		switch0@0 {
+		switch@10 {
 			compatible = "qca,qca8337";
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			reg = <0>;
+			reg = <0x10>;
 
 			ports {
 				#address-cells = <1>;
@@ -108,3 +114,56 @@ Example:
 			};
 		};
 	};
+
+for the internal master mdio-bus configuration:
+
+	&mdio0 {
+		switch@10 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+					fixed-link {
+						speed = 1000;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "wan";
+				};
+			};
+		};
+	};