Merge tag 'pinctrl-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control changes from Linus Walleij:
 "Here is the bulk of pin control changes for the v3.12 series.  Most of
  the relevant information is in the tag.

  I merged in v3.11-rc7 last week to get rid of a largeish conflict
  within the sunxi (AllWinner) driver in linux-next and fix up the
  non-trivial merge the right way.  That driver had a rather large fix
  adding locking late in the release cycle.

  Overall the bulk changes this time is cleanups and refactorings and
  not much new features, which is nice.

   - Refactorings for generic pin config handling in the core.

   - Factor out a set of device tree utilities for use in all drivers,
     to parse and allocate maps from the device tree.

   - Some fixes to the core such as more nitpicky locking.

   - Pushed down config array iteration into the drivers.

     This patch is necessary for drivers that want to iterate over
     configs and pile up a stack of alterations to the same register(s),
     or if the driver wants to take a local spinlock when committing the
     configuration.

   - A new driver for the Texas Instruments Palmas PMIC by Laxman
     Dewangan.  This is used on the Tegra systems.

   - A major cleanup and modernization of the PFC (Super Hitachi and ARM
     SHmobile) pin controller and subdrivers.

   - Support for the A20 and A31 sunxi (AllWinner) SoCs.

   - A huge pile of fixes and cleanups: Axel Lin, Jingoo Han Dan
     Carpenter, Julia Lawall and Sachin Kamat did an excellent job here"

* tag 'pinctrl-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (124 commits)
  pinctrl: sunxi: Fix off-by-one for valid offset range checking
  pinctrl: sunxi: drop lock on error path
  pinctrl: pinconf-generic: Remove ti prefix in dev_err messages
  pinctrl: rockchip: Implement .request() and .free() callbacks
  pinctrl: at91: fix get_pullup/down function return
  pinctrl: sh-pfc: remove unnecessary platform_set_drvdata()
  pinctrl: Add s5pv210 support to pinctrl-exynos
  pinctrl: utils: include export.h to avoid warnings
  pinctrl: s3c24xx: off by one in s3c24xx_eint_init()
  pinctrl: mvebu: testing the wrong variable
  pinctrl: abx500: fix bitwise AND test
  pinctrl: mvebu: Convert to use devm_ioremap_resource
  pinctrl: Pass all configs to driver on pin_config_set()
  pinctrl: tz1090-pdc: Convert to devm_ioremap_resource
  pinctrl: tz1090: Convert to devm_ioremap_resource
  pinctrl: tegra: Convert to devm_ioremap_resource
  pinctrl: rockchip: Simplify pin_to_bank equation
  pinctrl: spear: Convert to devm_ioremap_resource
  pinctrl: rockchip: Remove of_match_ptr macro for DT only driver
  pinctrl: palmas: PINCTRL_PALMAS needs to select PINMUX
  ...

4 files changed, 154 insertions, 41 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index d933af370697..6cec6ff20d2e 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -75,23 +75,36 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
 		gpio-controller;
 	};
 
-2.1) gpio-controller and pinctrl subsystem
-------------------------------------------
+2.1) gpio- and pin-controller interaction
+-----------------------------------------
 
-gpio-controller on a SOC might be tightly coupled with the pinctrl
-subsystem, in the sense that the pins can be used by other functions
-together with optional gpio feature.
+Some or all of the GPIOs provided by a GPIO controller may be routed to pins
+on the package via a pin controller. This allows muxing those pins between
+GPIO and other functions.
 
-While the pin allocation is totally managed by the pin ctrl subsystem,
-gpio (under gpiolib) is still maintained by gpio drivers. It may happen
-that different pin ranges in a SoC is managed by different gpio drivers.
+It is useful to represent which GPIOs correspond to which pins on which pin
+controllers. The gpio-ranges property described below represents this, and
+contains information structures as follows:
 
-This makes it logical to let gpio drivers announce their pin ranges to
-the pin ctrl subsystem and call 'pinctrl_request_gpio' in order to
-request the corresponding pin before any gpio usage.
+	gpio-range-list ::= <single-gpio-range> [gpio-range-list]
+	single-gpio-range ::=
+			<pinctrl-phandle> <gpio-base> <pinctrl-base> <count>
+	gpio-phandle : phandle to pin controller node.
+	gpio-base : Base GPIO ID in the GPIO controller
+	pinctrl-base : Base pinctrl pin ID in the pin controller
+	count : The number of GPIOs/pins in this range
 
-For this, the gpio controller can use a pinctrl phandle and pins to
-announce the pinrange to the pin ctrl subsystem. For example,
+The "pin controller node" mentioned above must conform to the bindings
+described in ../pinctrl/pinctrl-bindings.txt.
+
+Previous versions of this binding required all pin controller nodes that
+were referenced by any gpio-ranges property to contain a property named
+#gpio-range-cells with value <3>. This requirement is now deprecated.
+However, that property may still exist in older device trees for
+compatibility reasons, and would still be required even in new device
+trees that need to be compatible with older software.
+
+Example:
 
 	qe_pio_e: gpio-controller@1460 {
 		#gpio-cells = <2>;
@@ -99,16 +112,8 @@ announce the pinrange to the pin ctrl subsystem. For example,
 		reg = <0x1460 0x18>;
 		gpio-controller;
 		gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>;
+	};
 
-    }
-
-where,
-   &pinctrl1 and &pinctrl2 is the phandle to the pinctrl DT node.
-
-   Next values specify the base pin and number of pins for the range
-   handled by 'qe_pio_e' gpio. In the given example from base pin 20 to
-   pin 29 under pinctrl1 with gpio offset 0 and pin 50 to pin 69 under
-   pinctrl2 with gpio offset 10 is handled by this gpio controller.
-
-The pinctrl node must have "#gpio-range-cells" property to show number of
-arguments to pass with phandle from gpio controllers node.
+Here, a single GPIO controller has GPIOs 0..9 routed to pin controller
+pinctrl1's pins 20..29, and GPIOs 10..19 routed to pin controller pinctrl2's
+pins 50..59.
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index aeb3c995cc04..1958ca9f9e5c 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -127,21 +127,20 @@ whether there is any interaction between the child and intermediate parent
 nodes, is again defined entirely by the binding for the individual pin
 controller device.
 
-== Using generic pinconfig options ==
+== Generic pin configuration node content ==
 
-Generic pinconfig parameters can be used by defining a separate node containing
-the applicable parameters (and optional values), like:
+Many data items that are represented in a pin configuration node are common
+and generic. Pin control bindings should use the properties defined below
+where they are applicable; not all of these properties are relevant or useful
+for all hardware or binding structures. Each individual binding document
+should state which of these generic properties, if any, are used, and the
+structure of the DT nodes that contain these properties.
 
-pcfg_pull_up: pcfg_pull_up {
-	bias-pull-up;
-	drive-strength = <20>;
-};
-
-This node should then be referenced in the appropriate pinctrl node as a phandle
-and parsed in the driver using the pinconf_generic_parse_dt_config function.
-
-Supported configuration parameters are:
+Supported generic properties are:
 
+pins			- the list of pins that properties in the node
+			  apply to
+function		- the mux function to select
 bias-disable		- disable any pin bias
 bias-high-impedance	- high impedance mode ("third-state", "floating")
 bias-bus-hold		- latch weakly
@@ -160,7 +159,21 @@ low-power-disable	- disable low power mode
 output-low		- set the pin to output mode with low level
 output-high		- set the pin to output mode with high level
 
-Arguments for parameters:
+Some of the generic properties take arguments. For those that do, the
+arguments are described below.
+
+- pins takes a list of pin names or IDs as a required argument. The specific
+  binding for the hardware defines:
+  - Whether the entries are integers or strings, and their meaning.
+
+- function takes a list of function names/IDs as a required argument. The
+  specific binding for the hardware defines:
+  - Whether the entries are integers or strings, and their meaning.
+  - Whether only a single entry is allowed (which is applied to all entries
+    in the pins property), or whether there may alternatively be one entry per
+    entry in the pins property, in which case the list lengths must match, and
+    for each list index i, the function at list index i is applied to the pin
+    at list index i.
 
 - bias-pull-up, -down and -pin-default take as optional argument on hardware
   supporting it the pull strength in Ohm. bias-disable will disable the pull.
@@ -170,7 +183,5 @@ Arguments for parameters:
 - input-debounce takes the debounce time in usec as argument
   or 0 to disable debouncing
 
-All parameters not listed here, do not take an argument.
-
 More in-depth documentation on these parameters can be found in
 <include/linux/pinctrl/pinconfig-generic.h>
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt
new file mode 100644
index 000000000000..734d9b04d533
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt
@@ -0,0 +1,96 @@
+Palmas Pincontrol bindings
+
+The pins of Palmas device can be set on different option and provides
+the configuration for Pull UP/DOWN, open drain etc.
+
+Required properties:
+- compatible: It must be one of following:
+  - "ti,palmas-pinctrl" for Palma series of the pincontrol.
+  - "ti,tps65913-pinctrl" for Palma series device TPS65913.
+  - "ti,tps80036-pinctrl" for Palma series device TPS80036.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Palmas's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+list of pins. This configuration can include the mux function to select on
+those pin(s), and various pin configuration parameters, such as pull-up,
+open drain.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+Optional properties:
+- ti,palmas-enable-dvfs1: Enable DVFS1. Configure pins for DVFS1 mode.
+	Selection primary or secondary function associated to I2C2_SCL_SCE,
+	I2C2_SDA_SDO pin/pad for DVFS1 interface
+- ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode.
+	Selection primary or secondary function associated to GPADC_START
+	and SYSEN2 pin/pad for DVFS2 interface
+
+This binding uses the following generic properties as defined in
+pinctrl-bindings.txt:
+
+Required: pins
+Options: function, bias-disable, bias-pull-up, bias-pull-down,
+	 bias-pin-default, drive-open-drain.
+
+Note that many of these properties are only valid for certain specific pins.
+See the Palmas device datasheet for complete details regarding which pins
+support which functionality.
+
+Valid values for pin names are:
+	gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7, gpio8, gpio9,
+	gpio10, gpio11, gpio12, gpio13, gpio14, gpio15, vac, powergood,
+	nreswarm, pwrdown, gpadc_start, reset_in, nsleep, enable1, enable2,
+	int.
+
+Valid value of function names are:
+	gpio, led, pwm, regen, sysen, clk32kgaudio, id, vbus_det, chrg_det,
+	vac, vacok, powergood, usb_psel, msecure, pwrhold, int, nreswarm,
+	simrsto, simrsti, low_vbat, wireless_chrg1, rcm, pwrdown, gpadc_start,
+	reset_in, nsleep, enable.
+
+There are 4 special functions: opt0, opt1, opt2 and opt3. If any of these
+functions is selected then directly pins register will be written with 0, 1, 2
+or 3 respectively if it is valid for that pins or list of pins.
+
+Example:
+	palmas: tps65913 {
+		....
+		pinctrl {
+			compatible = "ti,tps65913-pinctrl";
+			ti,palmas-enable-dvfs1;
+			pinctrl-names = "default";
+			pinctrl-0 = <&palmas_pins_state>;
+
+			palmas_pins_state: pinmux {
+				gpio0 {
+					pins = "gpio0";
+					function = "id";
+					bias-pull-up;
+				};
+
+				vac {
+					pins = "vac";
+					function = "vacok";
+					bias-pull-down;
+				};
+
+				gpio5 {
+					pins = "gpio5";
+					function = "opt0";
+					drive-open-drain = <1>;
+				};
+			};
+		};
+		....
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
index 36281e7a2a46..257677de3e6b 100644
--- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -12,6 +12,7 @@ Required Properties:
   - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller,
   - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
   - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
+  - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller,
   - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
   - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
   - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
@@ -128,7 +129,7 @@ B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
      - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller
        found on Samsung S3C64xx SoCs,
      - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
-       found on Samsung Exynos4210 SoC.
+       found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs.
    - interrupt-parent: phandle of the interrupt parent to which the external
      wakeup interrupts are forwarded to.
    - interrupts: interrupt used by multiplexed wakeup interrupts.